Using an LED as a sensor and visible light communication device in a smart illumination system

The need for more efficient illumination systems has led to the proliferation of Solid-State Lighting (SSL) systems, which offer optimized power consumption. SSL systems are comprised of LED devices which are intrinsically fast devices and permit very fast light modulation. This, along with the congestion of the radio frequency spectrum has paved the path for the emergence of Visible Light Communication (VLC) systems. VLC uses free space to convey information by using light modulation. Notwithstanding, as VLC systems proliferate and cost competitiveness ensues, there are two important aspects to be considered. State-of-the-art VLC implementations use power demanding PAs, and thus it is important to investigate if regular, existent Switched-Mode Power Supply (SMPS) circuits can be adapted for VLC use. A 28 W buck regulator was implemented using a off-the-shelf LED Driver integrated circuit, using both series and parallel dimming techniques. Results show that optical clock frequencies up to 500 kHz are achievable without any major modification besides adequate component sizing. The use of an LED as a sensor was investigated, in a short-range, low-data-rate perspective. Results show successful communication in an LED-to-LED configuration, with enhanced range when using LED strings as sensors. Besides, LEDs present spectral selective sensitivity, which makes them good contenders for a multi-colour LED-to-LED system, such as in the use of RGB displays and lamps. Ultimately, the present work shows evidence that LEDs can be used as a dual-purpose device, enabling not only illumination, but also bi-directional data communication.

The intersection of people, technology and local space. PPGIS and Web in practice for participatory planning

Dissertation submitted in partial fulfilment of the requirements for the Degree of Master of Science in Geospatial Technologies

Towards cryogenic liquid –vapor energy storage units for space applications

Dissertation to obtain the Doctoral degree in Physics Engineering

Multipacket reception in the presence of in-band full-duplex communication

In-Band Full-DupleX (IB-FDX) is defined as the ability for nodes to transmit and receive signals simultaneously on the same channel. Conventional digital wireless networks do not implement it, since a node’s own transmission signal causes interference to the signal it is trying to receive. However, recent studies attempt to overcome this obstacle, since it can potentially double the spectral efficiency of current wireless networks. Different mechanisms exist today that are able to reduce a significant part of the Self- Interference (SI), although specially tuned Medium Access Control (MAC) protocols are required to optimize its use. One of IB-FDX’s biggest problems is that the nodes’ interference range is extended, meaning the unusable space for other transmissions and receptions is broader. This dissertation proposes using MultiPacket Reception (MPR) to address this issue and adapts an already existing Single-Carrier with Frequency-Domain Equalization (SC-FDE) receiver to IB-FDX. The performance analysis suggests that MPR and IB-FDX have a strong synergy and are able to achieve higher data rates, when used together. Using analytical models, the optimal transmission patterns and transmission power were identified, which maximize the channel capacity with the minimal energy consumption. This was used to define a new MAC protocol, named Full-duplex Multipacket reception Medium Access Control (FM-MAC). FM-MAC was designed for a single-hop cellular infrastructure, where the Access Point (AP) and the terminals implement both IB-FDX and MPR. It divides the coverage range of the AP into a closer Full-DupleX (FDX) zone and a farther Half-DupleX (HDX) zone and adds a tunable fairness mechanism to avoid terminal starvation. Simulation results show that this protocol provides efficient support for both HDX and FDX terminals, maximizing its capacity when more FDX terminals are used.

Molecular mobility of n-ethylene glycol dimethacrylate glass formers upon free radical polymerization

Quando um líquido evita a cristalização durante o arrefecimento, diz-se que entra no estado sobrearrefecido. Se a temperatura continuar a diminuir, o consequente aumento da viscosidade reflecte-se na mobilidade molecular de tal maneira que os tempos característicos se tornam da mesma ordem de grandeza que os tempos acessíveis experimentalmente. Se o arrefecimento continuar, o líquido altamente viscoso acaba por vitrificar, i.e. entra no estado vítreo onde apenas os movimentos locais são permitidos. Os monómeros da família n -etileno glicol dimetacrilato ( n -EGDMA, para n = 1 até 4, que constituem o objecto deste estudo, facilmente evitam a cristalização, sendo pois bons candidatos para estudar a mobilidade molecular nos estados sobrearrefecido e vítreo. A Espectroscopia de Relaxação Dieléctrica (DRS) foi a técnica escolhida para obter informação detalhada sobre a sua dinâmica molecular (Capítulos 1 e 2). A primeira parte deste trabalho consistiu na caracterização dieléctrica dos processos de relaxação existentes acima e abaixo da temperatura de transição vítrea (g T ), a qual aumenta com o aumento do peso molecular (w M ), sendo este resultado confirmado por Calorimetria Diferencial de Varrimento (DSC). No que respeita ao processo cooperativo a , associado à transição vítrea, e ao processo secundário b, observa-se uma dependência com w M , enquanto que o outro processo secundário, g , aparenta ser independente deste factor (Capítulo 3). Nos capítulos seguintes, foram levadas a cabo diferentes estratégias com o objectivo de clarificar os mecanismos que estão na origem destas duas relaxações secundárias (b e g ), assim como conhecer a sua respectiva relação com a relaxação principal (a ). Do estudo, em tempo real, da polimerização isotérmica via radicais livres do TrEGDMA por Calorimetria de Varrimento Diferencial com Modulação de Temperatura (TMDSC), levado a cabo a temperaturas abaixo da g T do polímero final, concluem-se entre outros, dois importantes aspectos: i) que a vitrificação do polímero em formação conduz a graus de conversão relativamente baixos, e ii) que o monómero que está por reagir é expulso da rede polimérica que se forma, dando lugar a uma clara separação de fases (Capítulo 4). Com base nesta informação, o passo seguinte foi estudar separadamente a polimerização isotérmica do di-, tri- e tetra-EGDMA, dando especial atenção às alterações de mobilidade do monómero ainda por reagir. Com as restrições impostas pela formação de ligações químicas, as relaxações a e b detectadas no monómero tendem a desaparecer no novo polímero formado, enquanto que a relaxação g se mantém quase inalterada. Os diferentes comportamentos que aparecem durante a polimerização permitiram a atribuição da origem molecular dos processos secundários: o processo g foi associado ao movimento twisting das unidades etileno glicol, enquanto que a rotação dos grupos carboxilo foi relacionada com a relaxação b (Capítulo 5). No que respeita ao próprio polímero, um processo de relaxação adicional foi detectado, pol b , no poly-DEGDMA, poly-TrEGDMA e poly-TeEGDMA, com características similares ao encontrado nos poli(metacrilato de n -alquilo). Este processo foi confirmado e bem caracterizado aquando do estudo da copolimerização do TrEGDMA com acrilato de metilo (MA) para diferentes composições (Capítulo 6). Para finalizar, o EGDMA, o elemento mais pequeno da família de monómeros estudada, além de vitrificar apresenta uma marcada tendência para cristalizar quer a partir do estado líquido ou do estado vítreo. Durante a cristalização, a formação de uma fase rígida afecta principalmente o processo a , cuja intensidade diminui sem no entanto se observarem modificações significativas na dependência do tempo de relaxação característico com a temperatura. Por outro lado, o processo secundário b torna-se melhor definido e mais estreito, o que pode ser interpretado em termos de uma maior homogeneidade dos micro-ambientes associados aos movimentos locais(Capítulo 7).

Unlimited or disrupted communication? How does the development of the mobile phone effect our ability of social action?

The aim of this essay is to discuss the thesis of the German Sociologist Günter Burkhart that in modern societies a phenomenon appeared which he calls “handymania”, an excessive and nearly addictive use of the mobile phones especially from adolescents. After a short overview about the history of the cell phone, I will relate this development to Jürgen Habermas “theory of communicative action”, more precisely to his diagnosis of a pathological society (“lifeworld”) to find out if the “handymania” could be one expression of it. Adjacent I will present social-psychological theories from E.H.Erikson and Tilmann Habermas to ascertain whether juveniles could really be a high-risk group for this kind of addiction. I will focus on the ability to communicate in an Habermasian way that could be seriously harmed by the unregulated usage of cell phones.

Children, space, and the urban street: an ethnomathematics posture

Dissertation presented for the PhD Degree in Education Science – Curricular Theory and Science Teaching, by Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

Société rurale, société urbaine: espaces en interaction

La sociologie et les nouveaux défis de la modernisation, Porto, pp. 315-326

Innovation through virtual communities of practice: motivations and constraints in the knowledge-creation process

This paper appears in International Journal of Projectics. Vol 4(1), pp. 39-49

POST-PROCESSING TECHNIQUES SUITABILITY FOR MESOLEVEL FREE BOUNDARY FLOWS

Reliable flow simulation software is inevitable to determine an optimal injection strategy in Liquid Composite Molding processes. Several methodologies can be implemented into standard software in order to reduce CPU time. Post-processing techniques might be one of them. Post-processing a finite element solution is a well-known procedure, which consists in a recalculation of the originally obtained quantities such that the rate of convergence increases without the need for expensive remeshing techniques. Post-processing is especially effective in problems where better accuracy is required for derivatives of nodal variables in regions where Dirichlet essential boundary condition is imposed strongly. In previous works influence of smoothness of non-homogeneous Dirichlet condition, imposed on smooth front was examined. However, usually quite a non-smooth boundary is obtained at each time step of the infiltration process due to discretization. Then direct application of post-processing techniques does not improve final results as expected. The new contribution of this paper lies in improvement of the standard methodology. Improved results clearly show that the recalculated flow front is closer to the ”exact” one, is smoother that the previous one and it improves local disturbances of the “exact” solution.

Scale-free networks and scalable interdomain routing

Trabalho apresentado no âmbito do Mestrado em Engenharia Informática, como requisito parcial para obtenção do grau de Mestre em Engenharia Informática

Post-processing Techniques in Free Boundary Flows during Liquid Composite Moulding Processes

Post-processing a finite element solution is a well-known technique, which consists in a recalculation of the originally obtained quantities such that the rate of convergence increases without the need for expensive remeshing techniques. Postprocessing is especially effective in problems where better accuracy is required for derivatives of nodal variables in regions where Dirichlet essential boundary condition is imposed strongly. Consequently such an approach can be exceptionally good in modelling of resin infiltration under quasi steady-state assumption by remeshing techniques and with explicit time integration, because only the free-front normal velocities are necessary to advance the resin front to the next position. The new contribution is the post-processing analysis and implementation of the freeboundary velocities of mesolevel infiltration analysis. Such implementation ensures better accuracy on even coarser meshes, which in consequence reduces the computational time also by the possibility of employing larger time steps.

MASS CONSERVATION ENHANCEMENT OF FREE BOUNDARY FLOWS IN COMPOSITES MANUFACTURING

Undesirable void formation during the injection phase of the liquid composite molding process can be understood as a consequence of the non-uniformity of the flow front progression, caused by the dual porosity of the fiber perform. Therefore the best examination of the void formation physics can be provided by a mesolevel analysis, where the characteristic dimension is given by the fiber tow diameter. In mesolevel analysis, liquid impregnation along two different scales; inside fiber tows and within the spaces between them; must be considered and the coupling between these flow regimes must be addressed. In such case, it is extremely important to account correctly for the surface tension effects, which can be modeled as capillary pressure applied at the flow front. When continues Galerkin method is used, exploiting elements with velocity components and pressure as nodal variables, strong numerical implementation of such boundary conditions leads to ill-posing of the problem, in terms of the weak classical as well as stabilized formulation. As a consequence, there is an error in mass conservation accumulated especially along the free flow front. This article presents a numerical procedure, which was formulated and implemented in the existing Free Boundary Program in order to significantly reduce this error.

Mass Conservation Enhancement of Free Boundary Mesolevel Flows during LCM Processes of Composites Manufacturing

Undesirable void formation during the injection phase of the liquid composite moulding process can be understood as a consequence of the non-uniformity of the flow front progression, caused by the dual porosity of the fibre perform. Therefore the best examination of the void formation physics can be provided by a mesolevel analysis, where the characteristic dimension is given by the fibre tow diameter. In mesolevel analysis, liquid impregnation along two different scales; inside fibre tows and within the open spaces between them; must be considered and the coupling between these flow regimes must be addressed. In such case, it is extremely important to account correctly for the surface tension effects, which can be modelled as capillary pressure applied at the flow front. Numerical implementation of such boundary conditions leads to ill-posing of the problem, in terms of the weak classical as well as stabilized formulation. As a consequence, there is an error in mass conservation accumulated especially along the free flow front. This contribution presents a numerical procedure, which was formulated and implemented in the existing Free Boundary Program in order to significantly reduce this error.

Educação alimentar infantil: potencialidades de estudantes de educação de infância

Resumo: Na promoção de comportamentos alimentares saudáveis ao longo da vida. que deve iniciar-se o mais precocemente possível, a educação alimentar é um elemento chave. O jardim-de-infância é um espaço efectivo na implementação de projectos de educação alimentar, onde os educadores de infância são actores imprescindíveis. Este estudo teve como objectivo desenvolver uma metodologia apropriada para identificar as capacidades de estudantes de educação de infância e avaliar as suas aptidões no contexto da educação alimentar infantil. A população alvo do estudo foram estudantes do 4ºano da licenciatura em educação de infância de instituições públicas e privadas da área metropolitana de Lisboa (n=287). Construiu-se um videograma, integrador dos domínios da aprendizagem (cognitivo e afectivo) e dos factores associados aos comportamentos em saúde (predisponentes, capacitadores e de esforço). A construção dos questionários estruturou-se em: conhecimentos-atitudes-comportamentos.Pretendia-se que os estudantes transmitissem a sua opinião, de acordo com os questionários.Os estudantes manifestaram conhecimentos, no âmbito da alimentação infantil e da utilidade e aplicabilidade da educação alimentar.Nenhum estudante apresentou conhecimentos negativos, numa escala de zero a 18 valores, 86,9% obtiveram uma classificação entre 11 e 17 valores e 13,1% a classificação máxima.A atitude dos estudantes revelou-se consensual com o desejável, 98,5% apresentaram atitudes positivas face aos aspectos estruturadores das actividades de educação alimentar.No domínio do "saber fazer" 51,0% dos estudantes demonstraram fragilidades no seu desempenho/comportamento. Em conclusão, a utilização do questionário demonstrou ser apropriado para a medição dos conhecimentos, das atitudes e como forma de os estudantes, após visionarem o videograma, espelharem o seu desempenho/comportamento face à representação do educador de infância. A taxa de resposta nunca foi inferior a 98,9% (n=284). No domínio dos conhecimentos, os estudantes manifestaram concepções positivas no campo da alimentação infantil e da educação alimentar. As atitudes enfatizaram-se no domínio afectivo, nos aspectos relacionais e comunicacionais. No domínio dos comportamentos, 91,8% dos estudantes apresentaram dificuldades na identificação dos aspectos menos correctos do desempenho dos actores do video, o que pode sugerir lacunas no âmbito do "saber fazer". Abstract:Nutrition education is key element to promote lifelong healthy eating behaviours and it must begin since early stages of life. Nursery schools are an effective space in the implementation of nutrition education projects, where the nursery teachers are indispensable actors. The aim of this study was to develop an appropriate methodology to identify nursery education student´s skills and evaluate their attitudes in the childhood nutrition education's context. The study's population were students of the 4th degree in private and public nursery education universities in Lisbon metropolitan area (n=287). A video integrator of learning domains (cognitive and affective) and of factors associated with health behaviours (predisposing, enabling and reinforcing) was developed. Questionnaire´s construction was structured in: knowledge-attitudes-behaviours.According to the questionnaires students were asked to transmit their opinion. Students revealed knowledge, in the scope of the childhood nutrition and in utility and applicability of nutrition education. No students presented negative results in knowledge ina zero - 18 scale; 86,9% students obtained a classification between 11 and 17 and the maximum classification was obtained by 13.1% students. Student's attitude was according to win the desirable, 98,5% student´s revealed positive attitudes in the nutrition education's structure aspects of chilhood activities.In the domain of the "know to do" 51,0% of students showed fragilities in their performance/behaviour. In conclusion, the questionnaire´s utilization confirm to be appropriated in measurement knowledge and attitudes and also, after watching the video, as a way for students reflect their performance/behaviour face to the nursery teacher´s representation. Answer´s rate was never lower than 98.9% (n=284). In the knowledge's domain students demonstrated positive conceptions in the childhood nutrition and nutrition education's fields. Attitudes were emphasized in the effective domain in the communication and relational aspects. In behaviour's domain 91.8% students presented difficulties in identifying the less correct aspects of the video actor's performance what may suggest gaps in the "know to do" scope.