Ecophysiology of Ruditapes decussatus

The physiological responses of the clam R. decussatus from the Ria Formosa, southern Portugal, were examined in relation to normoxia, hypoxia (11, 6, 3 and 1.2 kPa) and anoxia; acute elevation of temperature (at 20, 27 and 32 °C), and its effect on the resistance to air exposure (at 20, 28 and 35 °C); current velocity (0.6, 3, 8 17, 24 and 36 cm. s-1) and turbidity (10, 100 and 300 mg. l-1 dry weight of particulate matter), and the efficiency of this species in retaining particles of different size (at 10 and 100 mg. l-1); and to copper contamination considering both short-term acute exposure to high levels (0.1-10 mg Cu. l-1) and chronic environmental levels (0.01 mg Cu. l-1). Clearance rates, respiration rates, absorption efficiency and excretion rates were assessed through the physiological energetics in terms of the energy budget and scope for growth (SFG). Stress independent respiration rates (R) and clearance rates (CR) were observed in relation to hypoxia down to 12 kPa and 6 kPa, respectively. Anoxic rates were 3.6 % of normoxic rates. Scope for growth was greatly reduced under extreme hypoxia (14 % of SFG in normoxia). Respiration rate was temperature independent in the range 20-32 °C but the decline in clearance rate resulted in negative SFG at 32 °C. Gaping during air exposure and the maintenance of faster aerobic metabolism led to 100 % mortality in 20 hours at 35 °C, 4 days at 28 °C and 5 days at 20 °C. Low current velocities (≤ 8 cm. s-1) supported high clearance rates. Shear stresses ≥ 0.9 Pa induced sediment movement and disturbed the feeding processes resulting in decreased clearance rates (at 36 cm. s-1, is 10 % of maximum CR). The observed ability of jetting out depleted water at a different level than the one of the inhalant current results is an important adaptation of clams to the slow currents of sheltered environments. Ingestion at high seston concentrations (> 100 mg. l-1) is controled by reducing the amount filtered, lowering CR (to 30 % of CR at low seston loads) and producing pseudofeces. Observed efficient retention of particles (70-100 %) in the range 3 to 8 μm is beneficial when algal cells are diluted by fine silt particles as it is likely to occur in the clams natural environment. R. decussatus in the short term escaped the exposure to copper by valve closure and therefore acute tests are not applicable to adult clams of this species. At environmental levels chronic exposure to copper did not induce lethal effects during the exposure period (20 days), but scope for growth was reduced to c. 30 %, indicating sustained impairment of physiological functions. The sensitivity of the physiological energetics and the integrated scope for growth measurement in assessing stress effects caused by natural environmental factors was highlighted.

The Gap Between Knowledge and Action: Obstacles, Restraints and Deficits During the Execution of Refurbishments

This article outlines the initial draft of a PhD project which investigates refurbishment or rehabilitation projects in two German cities. The study focuses on obstacles, restraints and deficits as well as factors of success, which can be identified during the execution of the refurbishments. Moreover the study examines the process of the refurbishment itself, the general conditions under which the refurbishments are being executed as well as the implementation of sustainability criteria. First the article gives a short summary of the theoretical considerations of the study. In this respect it shortly outlines the global conditions of urban development and conducting challenges for cities in the 21st century, guiding principles of a sustainable urban development as well as goals of sustainable refurbishments. Finally the article shortly describes the case studies and presents the initial results of the empirical work.

In-situ X-ray diffraction studies during growth of Ni-Ti shape memory alloy films and their complementary ex-situ characterization

Shape Memory Alloy (SMA) Ni-Ti films have attracted much interest as functional and smart materials due to their unique properties. However, there are still important issues unresolved like formation of film texture and its control as well as substrate effects. Thus, the main challenge is not only the control of the microstructure, including stoichiometry and precipitates, but also the identification and control of the preferential orientation since it is a crucial factor in determining the shape memory behaviour. The aim of this PhD thesis is to study the optimisation of the deposition conditions of films of Ni-Ti in order to obtain the material fully crystallized at the end of the deposition, and to establish a clear relationship between the substrates and texture development. In order to achieve this objective, a two-magnetron sputter deposition chamber has been used allowing to heat and to apply a bias voltage to the substrate. It can be mounted into the six-circle diffractometer of the Rossendorf Beamline (ROBL) at the European Synchrotron Radiation Facility (ESRF), Grenoble, France, enabling an in-situ characterization by X-ray diffraction(XRD) of the films during their growth and annealing. The in-situ studies enable us to identify the different steps of the structural evolution during deposition with a set of parameters as well as to evaluate the effect of changing parameters on the structural characteristics of the deposited film. Besides the in-situ studies, other complementary ex-situ characterization techniques such as XRD at a laboratory source, Rutherford backscattering spectroscopy(RBS), Auger electron spectroscopy (AES), cross-sectional transmission electron microscopy (X-TEM), scanning electron microscopy (SEM), and electrical resistivity (ER) measurements during temperature cycling have been used for a fine structural characterization. In this study, mainly naturally and thermally oxidized Si(100) substrates, TiN buffer layers with different thicknesses (i.e. the TiN topmost layer crystallographic orientation is thickness dependent) and MgO(100) single crystals were used as substrates. The chosen experimental procedure led to a controlled composition and preferential orientation of the films. The type of substrate plays an important role for the texture of the sputtered Ni-Ti films and according to the ER results, the distinct crystallographic orientations of the Ni-Ti films influence their phase transformation characteristics.

Kinetic measurements during transient film growth on zinc

Quimica Nova, Vol. 32, Nº2

Anti-vibration gloves and the forearm efforts during tools operations

The objective of this paper is to analyze the forearm muscular contraction levels associated to the use of anti-vibration gloves, by comparing the contraction levels with gloves and without gloves. Two different vibration tools were used in a simulated work environment: (1) A compact Duty Multi-Cutter Bosch and (2) and a Percussion Drill with a drill bit Ø20 mm. Standard operations were performed by each subject in the following materials: (1) Performing cross- sectional cuts in 80x40 mm pine section and (2) performing 20 mm diameter holes in a concrete slab 2 x 2 m, 70 mm thick. The forearm contraction level were measured by surface electromyography in four different muscles: Flexor Digitorum Superficialis (FDS), Flexor Carpi Ulnaris (FCU), Extensor Carpi Radialis Longus (ECRL) e Extensor Carpi Ulnaris (ECU). For the flexor muscles (FDS, FCU), an increase tendency in muscular contraction was observed when the operations are performed without gloves (2-5% MVE increase in the FDS and 3-9% MVE increase in the FCU). For the extensor muscles ECU a decrease tendency in muscular contraction was observed when the operations are performed without gloves (1-10% MVE decrease). Any tendency was found in the ECRL muscle. ECU was the muscle with the highest contraction level for 79% and 71% of the operators, during the operations respectively with the multi-cutter (P50= 27-30%MVE) and with the percussion drill (P50=46-55%MVE). As a final conclusion from this study, anti- vibration gloves may increase the forearm fatigue in the posterior region of the forearm (ECU muscle) during operations with the mentioned tools

Neural correlations during brain activation in arithmetical tasks – an approach using electroencephalographic data

Dissertação apresentada na Faculdade de Ciências e Tecnologiea da Universidade Nova de Lisboa, para obtenção do Grau de Mestre em Engenharia Biomédica

Post-processing Techniques in Free Boundary Flows during Liquid Composite Moulding Processes

Post-processing a finite element solution is a well-known technique, which consists in a recalculation of the originally obtained quantities such that the rate of convergence increases without the need for expensive remeshing techniques. Postprocessing is especially effective in problems where better accuracy is required for derivatives of nodal variables in regions where Dirichlet essential boundary condition is imposed strongly. Consequently such an approach can be exceptionally good in modelling of resin infiltration under quasi steady-state assumption by remeshing techniques and with explicit time integration, because only the free-front normal velocities are necessary to advance the resin front to the next position. The new contribution is the post-processing analysis and implementation of the freeboundary velocities of mesolevel infiltration analysis. Such implementation ensures better accuracy on even coarser meshes, which in consequence reduces the computational time also by the possibility of employing larger time steps.

Mass Conservation Enhancement of Free Boundary Mesolevel Flows during LCM Processes of Composites Manufacturing

Undesirable void formation during the injection phase of the liquid composite moulding process can be understood as a consequence of the non-uniformity of the flow front progression, caused by the dual porosity of the fibre perform. Therefore the best examination of the void formation physics can be provided by a mesolevel analysis, where the characteristic dimension is given by the fibre tow diameter. In mesolevel analysis, liquid impregnation along two different scales; inside fibre tows and within the open spaces between them; must be considered and the coupling between these flow regimes must be addressed. In such case, it is extremely important to account correctly for the surface tension effects, which can be modelled as capillary pressure applied at the flow front. Numerical implementation of such boundary conditions leads to ill-posing of the problem, in terms of the weak classical as well as stabilized formulation. As a consequence, there is an error in mass conservation accumulated especially along the free flow front. This contribution presents a numerical procedure, which was formulated and implemented in the existing Free Boundary Program in order to significantly reduce this error.

Numerical Method to Predict Void Formation during The Liquid Composite Molding Process

Void formation during the injection phase of the liquid composite molding process can be explained as a consequence of the non-uniformity of the flow front progression. This is due to the dual porosity within the fiber perform (spacing between the fiber tows is much larger than between the fibers within in a tow) and therefore the best explanation can be provided by a mesolevel analysis, where the characteristic dimension is given by the fiber tow diameter of the order of millimeters. In mesolevel analysis, liquid impregnation along two different scales; inside fiber tows and within the open spaces between the fiber tows must be considered and the coupling between the flow regimes must be addressed. In such cases, it is extremely important to account correctly for the surface tension effects, which can be modeled as capillary pressure applied at the flow front. Numerical implementation of such boundary conditions leads to illposing of the problem, in terms of the weak classical as well as stabilized formulation. As a consequence, there is an error in mass conservation accumulated especially along the free flow front. A numerical procedure was formulated and is implemented in an existing Free Boundary Program to reduce this error significantly.

Sub-notificação de reacções adversas medicamentosas : um problema com solução? : contribuição para o conhecimento da sub-notificação de RAMs em Portugal e implementação de medidas minimizadoras do impacte

RESUMO - Introdução: As Reacções Adversas Medicamentosas (RAMs) constituem um grave problema de Saúde Pública em termos da mortalidade e morbilidade provocadas, tendo também um impacto económico considerável nos Sistemas de Saúde. Os Sistemas de Notificacão Espontânea de RAMs são considerados como o método de vigilância de medicamentos mais eficaz, sendo a sub-notificação de RAMs uma das suas maiores limitações. Em termos globais, foi estimado que apenas 6% de todas as reacções adversas são notificadas. Portugal apresenta uma taxa de notificação de RAMs relativamente baixa quando comparada com os países mais notificadores da Europa. São objectivos deste estudo: 1) caracterizar as atitudes e os comportamentos dos médicos, dos farmacêuticos e dos enfermeiros em Portugal Continental relativamente à notificação de RAMs; e 2) caracterizar a efectividade de intervenções educacionais destinadas a reduzir a sub-notificação de RAMs. Métodos: Numa primeira fase será efectuado um estudo de caso-controlo em médicos, farmacêuticos e enfermeiros de Portugal Continental, a exercer actividade no Servico Nacional de Saúde (SNS), de modo a caracterizar as suas atitudes e comportamentos relativamente à notificação de RAMs. Como casos serão considerados os Profissionais de Saúde que notificaram pelo menos uma RAM num determinado período e os controlos os Profissionais de Saúde que não notificaram qualquer RAM nesse mesmo período, sendo estes útimos seleccionados aleatoriamente. O estudo será conduzido através de um questionário de auto-resposta, em que as questões relativas às atitudes e comportamentos são baseadas nos “sete pecados mortais” de Inman. Será utilizada uma Escala Visual Analógica para registar as respostas, podendo estas ir de zero (totalmente em desacordo) até 10 (totalmente de acordo). Será utilizada uma análise de regressão logística para determinar o odds ratio ajustado (ORadj) da notificação de RAMs para uma mudança de exposição correspondente ao range interquartil para cada atitude. Numa segunda fase, será efectuado ensaio aleatorizado controlado de cluster, para caracterizar a efectividade das intervenções educacionais realizadas sobre as causas identificadas na primeira parte do trabalho, com o intuito de reduzir a sub-notificação de RAMs. Com base em informacão de 2007 foram identificados 43 clusters dispersos pelas várias Regiões de Saúde. As intervenções educacionais são compostas por uma apresentação com uma hora de duração complementada por um folheto recordatório. Serão ainda realizados dois sub-estudos, em que o V1.0, Final 28Set09 viii Sub-notificação de RAMs em Portugal – Um problema com solução ? primeiro tentará caracterizar o efeito de contaminação entre Profissionais de Saúde e o segundo pretende caracterizar a duração do efeito das intervenções educacionais. Resultados a atingir: Pretende-se, com a implementação deste projecto, aumentar o número de notificações de RAMs pelos médicos, farmacêuticos e enfermeiros em cerca de 110%, de modo a atingir-se uma taxa de notificação de aproximadamente 300 notificações por milhão de habitantes por ano (i.e., multiplicar por 2,1 o número notificações existentes). -------------------ABSTRACT - Introduction: The Adverse Drug Reactions (ADRs) are a serious Public Health problem in terms of mortality and morbidity caused, being also an economic burden for the health systems. The Spontaneous Adverse Event Reporting Systems are considered as the most effective drug surveillance methods, in which the ADR under-reporting represents one of its biggest limitations. It was estimated that only 6% of all adverse reactions are notified globally. When comparing with high ADR reporting rate countries Portugal shows a low ADR reporting rate. This study aims to: 1) characterize the physicians, pharmacists and nurses attitudes and behaviours related to ADR under-reporting; 2) characterize the educational interventions effectiveness to decrease the ADRs under-reporting. Methods: During a first phase a case-control study will be conducted in physicians, pharmacists and nurses in Continental Portugal working in the National Health System (NHS) in order to characterize their attitudes and behaviours related to ADR reporting. The Healthcare Professionals that have reported at least one ADR during a determined period will be considered as the cases and those that have not reported any ADR during the same period will be considered as the controls. The controls will be randomly selected. The study will be conducted through a self-administered questionnaire in which the questions related to the attitudes and behaviours are based in the Inmans’s “seven mortal sins”. A Visual Analogue Scale will be used to record the responses. The responses can range from 0 (totally disagree) to 10 (totally agree). Logistic regression will be used to determine the ADR reporting adjusted odds ratio (ORadj) for a change in the exposure corresponding to the interquartile range for each attitude. In the second phase of the study a cluster-randomized controlled trial will be conducted to characterize the educational interventions effectiveness focused on the first phase identified causes with the aim to decrease the ADRs under-reporting. Based in 2007’s information 43 clusters have been identified throughout the several Health Regions. The educational interventions are composed of one hour presentation complemented by an informational leaflet. Two sub-studies will be also conducted in which the first one will try to characterize the contamination effect between the Healthcare Professionals and the second to characterize the educational interventions effect duration. V1.0, Final 28Set09 x Sub-notificação de RAMs em Portugal – Um problema com solução ? Outcome: With the project implementation an increase of the ADR notifications performed by the physicians, pharmacists and nurses by 110% is aimed in order to obtain approximately 300 notifications per million habitants per year (i.e., multiply by 2,1 the existent notifications).

Evolution of Iberia during the Cenozoic with special emphasis on the formation of the Betic Cordillera and its relation with the western Mediterranean

The extensional process affecting Iberia during the Triassic and Jurassic times change from the end of the Cretaceous and, throughout the Palaeocene, the displacement between the African and European plates was clearly convergent and part of the future Internal Zone of the Betic Cordillera was affected. To the west, the Atlantic continued to open as a passive margin and, to the north, no significant deformation occurred. During the Eocene, the entire Iberian plate was subjected to compression. which caused major deformations in the Pyrenees and also in the Alpujarride and Nevado-Filabride, Internal Betic, complexes. In the Oligocene continued this situation, but in addition, the new extensional process ocurring in the western Mediterranean area, together with the constant eastward drift of Iberia due to Atlantic opening, compressed the eastern sector of Iberia, giving rise to the structuring of the Iberian Cordillera. The Neogene was the time when the Betic Cordillera reached its fundamental features with the westward displacement of the Betic-Rif Internal Zone, expelled by the progressive opening of the Algerian Basin, opening prolonged till the Alboran Sea. From the late Miocene onwards, all Iberia was affected by a N-S to NNW-SSE compression, combined in many points by a near perpendicular extension. Specially in eastern and southern Iberia a radial extension superposed these compression and extension.

SIN 319 AND VOSKR 27 AND THE TRIODION CYCLE IN THE LITURGICAL PRAXIS IN RUSSIA DURING THE STUDITE PERIOD

A Thesis Presented to the Faculty of Social and Human Science of the Universidade Nova de Lisboa in Candidacy for the Degree of Doctor of Philosophy in Musicology