Coupling organic substrate removal to methane production in a fully biological microbial electrolysis cell

Microbial electrolysis cells (MECs) are an innovative and emerging technique based on the use of solid-state electrodes to stimulate microbial metabolism for wastewater treatment and simultaneous production of value-added compounds (such as methane). This research studied the performance of a two-chamber MEC in terms of organic matter oxidation (at the anode) and methane production (at the cathode). MEC‟s anode had been previously inoculated with an activated sludge, whereas the cathode chamber inoculum was an anaerobic sludge (containing methanogenic microorganisms). During the experimentation, the bioanode was continuously fed with synthetic solutions in anaerobic basal medium, at an organic load rate (OLR) of around 1 g L-1 d-1, referred to the chemical oxygen demand (COD). At the beginning (Run I), the feeding solution contained acetate and subsequently (Run II) it was replaced with a more complex solution containing soluble organic compounds other than acetate. For both conditions, the anode potential was controlled at -0.1 V vs. standard hydrogen electrode, by means of a potentiostat. During Run I, over 80% of the influent acetate was anaerobically oxidized at the anode, and the resulting electric current was recovered as methane at the cathode (with a cathode capture efficiency, CCE, accounting around 115 %). The average energy efficiency of the system (i.e., the energy captured into methane relative to the electrical energy input) under these conditions was over 170%. However, reactor‟s performance decreased over time during this run. Throughout Run II, a substrate oxidation over 60% (on COD basis) was observed. The electric current produced (57% of coulombic efficiency) was also recovered as methane, with a CCE of 90%. For this run the MEC‟s average energy efficiency accounted for almost 170 %. During all the experimentation, a very low biomass growth was observed at the anode whereas ammonium was transferred through the cationic membrane and concentrated at the cathode. Tracer experiments and scanning electron microscopy analyses were also carried out to gain a deeper insight into the reactor performance and also to investigate the possible reasons for partial loss of performance. In conclusion, this research suggests the great potential of MEC to successfully treat low-strength wastewaters, with high energy efficiency and very low sludge production.

A regulação endócrina dos balanços de cálcio

RESUMO: As concentrações circulantes de cálcio são notavelmente constantes a despeito das variações diárias na absorção intestinal e na eliminação renal deste elemento. A regulação da calcémia é um sistema complexo que compreende vários factores controladores (a calcémia, a fosforémia, as concentrações circulantes de paratormona (PTH) e calcitriol além de muitos outros factores como hormonas esteróides em geral, outros iões como o magnésio e outros factores hormonais) e vários órgãos alvo (glândulas paratiroideias, osso, rim e intestino). As respostas dos órgãos alvo também são muito variadas. No caso mais simples, a cristalização de sais de cálcio corresponde a uma mudança de fase em que participam moléculas orgânicas que a iniciam, aceleram ou inibem. Em geral a combinação de um factor controlador com o respectivo receptor de membrana (para polipeptídeos ou iões) ou intracelular (hormonas esteróides) é apenas o primeiro passo de uma cadeia bioquímica que introduz uma enorme amplificação na resposta. A esta variedade de mecanismos de resposta correspondem grandes diferenças nos tempos de resposta que podem ser de minutos a semanas. É hoje possível “observar” (medir) com apreciável rigor nos líquidos biológicos (sangue, urina, fezes, etc.) os factores mais importantes do sistema de regulação da calcémia (cálcio, fósforo, paratormona e calcitriol) assim como administrar estes factores em experiências agudas. Esta possibilidade reflecte – se na literatura neste campo que tem vindo a crescer. O advento das técnicas da biologia molecular tem permitido a caracterização molecular de algumas das disfunções da homeostase do cálcio e é de esperar um diagnóstico fisiopatológico cada vez mais rigoroso dessas disfunções. Com o avanço dos conhecimentos nesta área que não cessa de aumentar temos cada vez maiores capacidades para fazer diagnósticos e é cada vez mais difícil interpretar com rigor os correspondentes quadros metabólicos. A análise ou síntese de sistemas complexos é a actividade mais nobre dos engenheiros que lhes permite desenhar pontes, diques, barcos, aviões ou automóveis. Com o aparecimento de computadores de médio ou grande porte foi – lhes possível utilizar descrições matemáticas não só para desenhar sistemas como ainda para interpretar eventuais falhas na sua operação. Essas descrições matemáticas consistem numa sequência de operações realizadas num computador segundo um “programa informático” que receberam a designação genérica de modelos, por analogia com as famosas leis (equações) da física que foram deduzidas a partir de um certo número de postulados e que permitem representar matematicamente processos físicos. As famosas leis de Newton são talvez os exemplos mais famosos de “modelos” de sistemas físicos. A introdução de modelos matemáticos em biologia e particularmente em medicina só se deu recentemente.MÉTODOS No trabalho que aqui se apresenta construiu - se um modelo simplificado da homeostase do cálcio destinado ao cálculo de variáveis observáveis (concentrações de cálcio, fósforo, PTH e calcitriol) de modo a poderem comparar-se valores calculados com valores observados. A escolha dos componentes do modelo foi determinada pela nossa experiência clínica e pela informação fisiopatológica e clínica publicada. Houve a preocupação de construir o modelo de forma modular de modo a ser possível a sua expansão sem grandes transformações na descrição matemática (e informática) já existente. Na sua fase actual o modelo não pode ser usado como instrumento de diagnóstico. É antes uma ferramenta destinada a esclarecer “em princípio” mecanismos fisiopatológicos. Usou – se o modelo para simular um certo número de observações publicadas e para exemplificar a sua eventual aplicação clínica na simulação de situações hipotéticas e na análise de possíveis mecanismos fisiopatológicos responsáveis por situações de hipo ou hipercalcémias. Simultaneamente fez – se uma análise dos dados acumulados relativos a doentes vistos no Serviço de Endocrinologia do Instituto Português de Oncologia de Francisco Gentil – Centro Regional Oncológico de Lisboa, S.A. CONCLUSÕES Numa população de 894 doentes com patologias variadas do Instituto Português de Oncologia de Lisboa os valores da calcémia tiveram uma distribuição normal unimodal com uma média de 9.56 mg/dl, e um erro padrão de 0.41 mg/dl. Estas observações sugerem que a calcémia está sujeita a regulação. A partir dos resultados publicados em que o metabolismo do cálcio foi perturbado por infusões de cálcio, calcitriol ou PTH, de estudos bioquímicos e fisiológicos sobre os mecanismos de acção de factores controladores da calcémia e do estudo do comportamento de órgãos alvo (paratiroideias, intestino, osso e rim) foi possível construir um modelo matemático de parâmetros concentrados do sistema de regulação da calcémia. As expressões analíticas usadas foram baseadas na cinética enzimática de modo a que os seus parâmetros tivessem um significado físico ou fisiológico simples. O modelo revelou apreciável robustez e flexibilidade. É estável quando não perturbado e transita entre estados estacionários quando perturbado. Na sua forma actual gera simulações que reproduzem satisfatoriamente um número apreciável de dados experimentais colhidos em doentes. Isto não significa que possa ser usado como instrumento de diagnóstico aplicável a doentes individuais. O desenho do modelo comporta a adição posterior de novas relações quando surgirem situações para as quais se revele insuficiente. A utilização exaustiva do modelo permitiu explicitar aspectos do metabolismo do cálcio que ou não estão contidas na sua formulação actual – o aparecimento de hipertrofia ou de adenomas das paratiroideias e as alterações na estrutura óssea , a participação de outros factores controladores – magnésio, ou estão insuficientemente descritas – alterações do metabolismo do fósforo nos hipoparatiroidismos. A análise dos dados relativos aos doentes do Serviço de Endocrinologia do IPO permitiu o início da caracterização dos tipos de patologia que representam e de possíveis mecanismos fisiopatológicos subjacentes. Estas observações são o ponto de partida para análises futuras. São exemplos das relações encontradas: a distribuição dos doentes por dois grandes grupos conforme a calcémia é determinada pelas concentrações circulantes de PTH ou estas são determinadas pela calcémia; a distribuição sazonal das concentrações de Vit. D25. no sangue; a correlação negativa entre estas e as concentrações de PTH no sangue. Também foi possível extrair a cinética do controlo da PTH sobre a síntese de calcitriol. O estudo dos níveis circulantes de PTH no pós-operatório imediato de doentes paratiroidectomizados permitiu determinar as suas taxas de degradação metabólica. O modelo permitiu simular as relações Ca/PTH no sangue, Ca/Fracção excretada da carga tubular, Ca/P no sangue para valores normais ou altos de Ca. Foram feitas simulações de situações fisiopatológicas (em “doentes virtuais”): infusões crónicas de cálcio, PTH e calcitriol; alterações no comportamento de receptores. Estas simulações correspondem a experiências que não podem ser realizadas em humanos. São exemplos da utilização do modelo na exploração de possíveis mecanismos fisiopatológicos através da observação de resultados quantitativos inacessíveis à intuição. O modelo foi útil em duas fases do trabalho: Primeiro, durante a sua síntese implicou uma escolha criticamente selectiva de informação, sua análise quantitativa e processamento, uma explicitação rigorosa (analítica) das relações funcionais entre os controladores e as variáveis e da sua integração numa estrutura global; Segundo, a simulação de situações experimentais ou clínicas (dados do Serviço de Endocrinologia do IPO) em doentes obrigou a explicitar raciocínios fisiopatológicos habitualmente formulados em bases puramente intuitivas. Esta prática revelou comportamentos óbvios após as simulações – acção reduzida das infusões PTH (simulação de hiperparatiroidismos primários) enquanto não há inibição total da respectiva secreção, necessidade de aumento da massa secretora da paratiroideia nas insuficiências renais avançadas, etc. A síntese e utilização do modelo não implicaram uma preparação matemática avançada e foram possíveis mercê da disponibilidade de “software” interactivo especificamente desenhado para a simulação de sistemas dinâmicos em que os programas se escrevem em inglês usando a simbologia simples da álgebra elementar. A função nobre de modelos desta natureza é semelhante à dos modelos usados pelos físicos desde o século XVII: permitir explicações de carácter geral funcionando como uma ferramenta intelectual para manipulação de conceitos e para a realização de “experiências pensadas” (“thought experiments”) respeitando certos princípios físicos (princípios de conservação) que estabelecem as fronteiras da realidade. -------ABSTRACT: Calcium blood levels are remarkably constant despite great variations in calcium daily intake, intestinal absorption and renal excretion. The regulation of the calcium concentration in the blood is achieved by a complex system that includes several controller factors (mainly the serum levels of calcium, phosphorus, parathyroid hormone (PTH) and calcitriol but also of steroid hormones, ions such as magnesium and other hormonal factors) and several target organs (parathyroid glands, bone, kidney and intestine). The functional response to the controlling factors obeys a variety of kinetics. The precipitation of calcium salts is a simple phase transition in which organic molecules may provide nucleation centres or inhibit the process. The combination of a controller factor with its receptor located in the cell membrane (for peptides or ions) or in the nucleus (for steroid hormones) is only the first step of a biochemical chain that introduces a huge amplification in the response. To this great variability of response we have to add the times of response that vary from minutes to weeks. It is possible to “observe” (measure) with great accuracy in biological fluids (blood, urine, faeces, etc.) the most important factors intervening in the calcium regulation (calcium, phosphorus, PTH and calcitriol). The response of the system to acute infusions of the controlling factors has also been studied. Using molecular biology techniques it has been possible to characterize some calcium homeostasis dysfunctions and better physiopathological diagnosis are expected. With the increasingly new knowledge in this area we have better capacity to diagnose but it is harder to explain correctly the underlying metabolic mechanisms. The analysis or synthesis of complex systems is the noble activity of engineers that enables them to draw bridges, dams, boats, airplanes or cars. With the availability of medium-large frame computers it was possible to use mathematical descriptions not only to draw systems but also to explain flaws in its operations. These mathematical descriptions are generally known as models by analogy with the laws (equations) of physics that allow the mathematical description of physical processes. In practice it is not possible to find general solutions for the mathematical descriptions of complex systems but (numeric) computations for specific situations can be obtained with digital computers. The introduction of mathematical models in biology and particularly in medicine is a recent event. METHODS In this thesis a simplified model of calcium homeostasis was built that enables the computation of observable variables (concentrations of calcium, phosphorus, PTH and calcitriol) and allows the comparison between the simulation values and observed values. The choice of the model’s components was made according to our clinical experience and to the published clinical and physiopathological data. The model has a modular design that allows future expansions with minor alterations in its structure. In its present form the model cannot be used for diagnosis. It is a tool designed to enlighten physiopathological processes. To exemplify its possible clinical application in the simulation of hypothetical situations and in the analysis of possible mechanisms responsible for hypo or hypercalcemias the model was used to simulate a certain number of published observations. An analysis of clinical and laboratory data from the Endocrinology Department of the Portuguese Cancer Institute (I.P.O.F.G.-C.R.O.L.,S.A.) is also presented. CONCLUSIONS In a population of 188 patients without an identifiable disease of the calcium metabolism at the Portuguese Cancer Institute the calcemia levels had a unimodal distribution with an average of 9.56 mg/dL and a S.E.M of 0.41 mg/dL. This observation confirms that serum calcium is regulated. Using published data; in which calcium metabolism was disrupted by calcium, PTH or calcitriol infusions; from biochemical and physiological studies of the action of controller factors on the calcemia; in which the response of target organs (parathyroid glands, intestine, bone, kidney) was studied it was possible to build a mathematical model of concentrated parameters of the calcium homeostasis. Analytical expressions used were based on enzymatic kinetics. The model is flexible and robust. It is stable when not disturbed and changes between steady states when disturbed. In its present form it provides simulations that reproduce closely a number of experimental clinical data. This does not mean that it can be used as a diagnostic tool for individual patients. The exhaustive utilisation of the model revealed the need of future expansions to include aspects of the calcium metabolism not included in its present form –hypertrophy or adenomas of the parathyroid glands, bone structure changes, participation of other controller factors such as magnesium – or insufficiently described – phosphate metabolism in hypoparathyroidism. The analysis of the data collected from the I.P.O.’s Endocrinology Department allowed the initial characterization of the different pathologies represented and of their possible physiopathological mechanisms. These observations are a starting point for future analysis. As examples of the relations found were: the distribution of patients in two groups according to the dependency of calcium by PTH levels or PTH levels by calcium concentration; the seasonal distribution of the serum concentrations of D25; its negative correlation with PTH concentration. It was also possible to extract the kinetics of the control of the synthesis of calcitriol by PTH. The analysis of immediate post-surgical levels of PTH in parathyroidectomized patients allowed the determination of its metabolic clearance. The model also allowed the simulation of the relations between Ca/PTH in blood, serum Ca/Fraction of tubular load excreted and Ca/P in blood for normal and high values of calcium. Simulations were made of pathological situations (in “virtual patients”): chronic infusions of calcium, PTH and calcitriol; changes in the characteristics of receptors. These simulations are not possible in real persons. They are an example of the use of this model in exploring possible mechanisms of disease through the observation of quantitative results not accessible to simple intuition. This model was useful in two phases: Firstly, its construction required a careful choice of data, its quantitative analysis and processing, an analytical description of the relations between controller factors and variables and their integration in a global structure. Secondly, the simulation of experimental or clinical (I.P.O.’s Endocrinology Department) data implied testing physiopathological explanations that previously were based on intuition. The construction and utilisation of the model didn’t demand an advanced mathematical preparation since user-friendly interactive software was used. This software was specifically designed for the simulation of dynamic systems. The programs are written in English using elementary algebra symbols. The essential function of this type of models is identical to that of those used by physicists since the XVII century which describe quantitatively natural processes and are an intellectual tool for the manipulation of concepts and the performance of “thought experiments” based in certain physical principles (conservation principles) that are the frontiers of reality.------------------RESUMÉE: Les concentrations circulantes de calcium sont constantes même pendant des variations de l’absorption intestinale et de l’élimination rénale de cet élément. La régulation de la calcémie est un système complexe qui comprend plusieurs éléments contrôleurs (la calcémie, la phosphorémie, les concentrations circulantes de l’hormone parathyroïdienne (PTH) e du calcitriol et d’autres comme les hormones stéroïdes ou des ions comme le magnésium) et plusieurs organes (glandes parathyroïdiennes, l’os, le rein et l’intestin). Les réponses de ces organes sont variées. Dans le cas plus simple, la cristallisation des sels de calcium correspond à un changement de phase dans lequel y participent des molécules organiques que la débutent, l’accélèrent ou l’inhibent. Généralement la combinaison d’un élément contrôleur avec leur récepteur de membrane (pour les peptides ou les ions) ou intracellulaire (pour les hormones stéroïdes) n’est que le premier pas d’une chaîne biochimique qu’introduit une grande amplification de la réponse. A cette variété de réponses correspondent des grandes différences des temps de réponses qu’y vont des minuits a semaines. Il est possible « observer » (mesurer) dans les fluides biologiques (sang, urine, fèces, etc.) les éléments plus importants du système de régulation de la calcémie (calcium, phosphate, PTH et le calcitriol) et les administrer en expérimentes aigus. Cette possibilité est visible dans la littérature publiée dans ce domaine qui est en croissance permanente. L’avenir des techniques de biologie moléculaire a permis caractériser des nombreuses dysfonctions de la régulation de la calcémie et on attend un diagnostique physiopathologique de ces dysfonctions chaque fois plus rigoureuses. Les connaissances dans ce domaine s’agrandissent et on a de plus de capacités pour faire des diagnostiques et il est chaque fois plus difficile les interpréter. L’analyse ou synthèse de systèmes complexes est l’activité plus noble des ingénieurs qui les permit dessiner des ponts, bateaux, avions ou automobiles. Avec des ordinateurs de médium ou grand port il les est possible utiliser descriptions mathématiques pour dessiner les systèmes et interpréter des éventuelles fautes d’opération. Ces descriptions mathématiques sont une séquence d’opérations réalisées dans un ordinateur selon « un programme informatique » qui ont reçu la désignation générique de modèles, pour analogie avec les équations de la physique qui ont été déduits d’un nombre de postulées et qu’ont permit représenter des processus physiques en équations mathématiques. Les fameuses équations de Newton sont peut-être les exemples plus connus des systèmes physiques. L’introduction des modèles mathématiques en biologie et en particulier en médecine est un évènement récent. Dans ce travaille, on a construit un modèle simplifié de l’homéostasie du calcium pour calculer les variables observables (concentrations de calcium, phosphate, PTH et calcitriol) pour les comparer. Les choix des components a été déterminés par notre expérience clinique et par l’information physiopathologique et clinique publiée. Le modèle a été construit de façon modulaire ce que permit leur postérieur expansion sans des grandes altérations dans la description mathématique et informatique déjà existante. Dans cette forme le modèle ne peut être utilisé comme un instrument de diagnostique. Il est un outil pour éclairer la physiopathologie. Le modèle a été utilisé pour simuler un certain nombre d’observations publiées et pour exemplifier leur possible utilisation clinique dans la simulation des hypothèses et de la physiopathologie des situations d’hypo ou hypercalcémie. On a fait une analyse des éléments des procès cliniques des malades observées dans le Service d’Endocrinologie de l’IPOFG-CROL, SA. Dans une population de 894 malades avec des différentes pathologies les valeurs de calcémie on une distribution uni modale avec une Médie de 9.56 mg/dL et une erreur standard de 0.41 mg/dL. Ces observations suggèrent que la calcémie soit sujette de régulation. En utilisant des résultats de travaux publiés dans lesquels le métabolisme du calcium a été changé par des infusions de calcium, calcitriol ou PTH, des études biochimiques et physiologiques sur des mécanismes d’action des éléments contrôleurs de la calcémie et de l’étude du comportement des organes cible (parathyroïdes, intestin, rein, os), il a été possible de construire un modèle mathématique de paramètres concentrés du système de régulation de la calcémie. Les expressions analytiques utilisées ont été basées sur la cinétique enzymatique de façon à que les paramètres aient eu une signification physique ou biologique. Le modèle est stable quand il n’est pas perturbé et transit entre états stationnaires quand il est sujet a des perturbations. A ce moment il fait des simulations qui reproduisent de façon satisfaisant un nombre d’observations expérimentales. La construction du modèle permit l’addiction de nouvelles relations dans les cas ou il est insuffisant. L’utilisation exhaustive du modèle a permit expliciter des aspects du métabolisme du calcium qui y ne sont pas compris – l’hyperplasie ou la formation des adénomes des parathyroïdes, les altérations de la structure des os, la participation d’outres éléments régulateurs (magnésium), ou sont insuffisamment décrites – les altérations du métabolisme des phosphates dans l’hypoparathyroidism. L’analyse de l’information des malades du Service d’Endocrinologie a permit caractériser les pathologies représentées et leurs possibles mécanismes physiopathologiques. Ces observations sont le point de départ pour les analyses futures. Sont des exemples des relations trouvées: la distribution des malades par deux groupes: ceux dans lequel la calcémie est déterminée par la PTH ou ceux dans lesquels la PTH est déterminée par la calcémie; la distribution sazonale de la concentration de la vitamine D; la corrélation négative entre la vitamine D et la PTH. On a eu la possibilité de déduire la cinétique de control de la PTH sur la synthèse du calcitriol. L’étude des niveaux circulants de PTH sur des sujets parathyroidectomisées a permit déduire leur taux de dégradation métabolique. Le modèle a permit simuler les relations Ca/PTH dans le sang, Ca/fraction éliminée par le rein, Ca/P dans le sang pour des valeurs normales ou hautes de calcium. On a fait des simulations de situations physiopathologiques (dans “malades virtuelles”): Infusions chroniques de calcium, PTH ou calcitriol; altérations des récepteurs. Ces simulations ne peuvent pas être réalisées dans les humains. Sont des exemples d’utilisation du modèle dans l’exploration des possibles mécanismes de la physiopathologie en observant des résultats quantitatifs inaccessibles à l’intuition. Le modèle a été utile pendant deux étapes des travaux: La première, dans sa construction on a choisi l’information disponible, son analyse quantitative, l’explicitation rigoureuse (analytique) des relations fonctionnelles entre les contrôleurs et les variables et sa intégration dans une structure globale. La deuxième, la simulation de situations expérimentales ou cliniques (du Service d’Endocrinologie) a obligé d’expliciter des raisonnements physiopathologiques généralement formulés utilisant l’intuition. Cette pratique a montré des comportements – action réduite des infusions de PTH (jusqu’à l’inhibition totale de leur respective sécrétion), nécessité d’augmenter la masse sécréteuse de la parathyroïde dans les insuffisants rénales, etc. La synthèse et utilisation du modèle n’ont pas besoin d’une formation avancée en mathématique et sont possibles grâce à un programme interactif qui a été conçu pour la simulation des systèmes dynamiques dans lesquels le programme se construit en anglais en utilisant la symbolique élémentaire de l’algèbre. La fonction noble de ces modèles est semblable à celles des physiques du XVII siècle: Permettre établir explications générales en fonctionnant comme un outil intellectuel pour manipuler des concepts et pour la réalisation d’expérimentes pensées en respectant certains principes de la physique (principe de la conservation) qu’établissent les frontières de la réalité.

Study and characterization of the ZnPc:C60/MoOx interface in organic solar cells by means of photoelectron spectroscopy

Dissertation to obtain the academic degree of Master in materials engineering submitted to the Faculty of science and engineering of Universidade Nova de Lisboa

Electrodialytic recovery of phosphorus and organic contaminants removal from sewage sludge

Phosphorus is a macronutrient essential to life which comes from phosphate rock, a non-renewable resource. Sewage sludge from wastewater treatment plants (WWTP) is a secondary resource rich in phosphorus that can be valorized. However, organic compounds are detected in sewage sludge, due to its non-polar and hydrophobic character, being considered an environmental risk. The present dissertation aims to study the efficiency of the electrodialytic process (ED) when applied to sewage sludge aiming phosphorus recovery and organic contaminants removal. Four organic compounds were analyzed: 17α-ethynylestradiol (EE2), bisphenol A (BPA), caffeine (Caf) and oxybenzone (MBPh). The experiments took place in an ED cell with two compartments and an anion exchange membrane, with the sludge in the cathode compartment. The experiments were carried out for three days with spiked sewage sludge (six assays). One control experiment was done without current, three experiments were carried out applying a constant current of 50, 75, and 100 mA and two experiments were carried out applying sequential currents: 50 mA, 75 mA and 100 mA and the opposite (100-75-50 mA). A qualitative and quantitative analysis of microorganisms existing in the samples was also done. At the end, the pH increased in the sewage sludge favoring phosphorus recovery. In terms of phosphorus, the highest recovery was achieved in the experiment run with 100 mA, where 70.3±2.0% of total phosphorus was recovered in the electrolyte. Generally, compounds degradation was favored by the current. Caf and MBPh achieved degradation percentages of 96.2±0.2% and 84.8±1.3%, respectively, in 100 mA assay. EE2 (83.1±1.7%) and BPA (91.8±4.6%) degradations were favored by 50 mA current. A total of 35 taxa from four different groups were identified, totalizing between 81,600-273,000 individuals per gram of initial sludges. After ED, microbial community population decreased between 47-98%. Arcella gibbosa represented 61% of the total observed organisms and revealed to be more tolerant to medium changes.

Removal of organic contaminants from wastewater using the electrodialytic process

Pharmaceuticals and personal care products (PPCPs) are widely used on a daily basis. After their usage they reach the wastewater treatment plants (WWTPs). These compounds have different physico-chemical characteristics, which makes them difficult to completely remove in the WWTPs, througth conventional treatments. Currently, there is no legislation regarding PPCPs thresholds in effluent discharge. But, even at vestigial concentrations, these compounds enclose environmental risks due to, e.g., endocrine disruption potential. There is a need of alternative techniques for their removal in WWTPs. The main goal of this work was to assess the use of electrodialytic (ED) process to remove PPCPs from the effluent to be discharged. A two-compartment ED cell was used testing (i) the effluent position in the cell (anode and cathode compartment); (ii) the use of anion (AEM) and cation exchange membrane (CEM); (iii) the treatment period (6, 12 and 24 hours); (iv) effluent recirculation and current steps; (v) the feasibility of sequential treatments. Phosphorus (P) removal from effluent and energetic costs associated to the process were also evaluated. Five PPCPs were studied – caffeine (CAF), bisphenol A (BPA), 17 β-estradiol (E2), ethinyl estradiol (EE2) and oxybenzone (MBPh). The ED process showed to be effective in the removal when effluent is in the anode compartment. Oxidation is suggested to be the main removal process, which was between 88 and 96%, for all the compounds, in 6 hours. Nevertheless, the presence of intermediates and/or by-products was also observed in some cases. Effluent recirculation should have a retention time in the ED cell big enough to promote removal whereas the current steps (effluent in anode compartment) slightly increased removal efficiencies (higher than 80% for all PPCPs). The sequential set of ED treatment (effluent in anode compartment) showed to be effective during both periods with a removal percentage between 80 and 95% and 73 to 88% in the case of AEM and CEM, respectively. Again, the main removal process is strongly suggested to be oxidation in the anode compartment. However, there was an increase of BOD5 and COD, which might be explained by effluent spiking, these parameters limiting the effluent discharge. From these treatments, the use of AEM, enhanced the P removal from effluent to minimize risk of eutrophication. Energetic costs of the best set-up (6 hours) are approximately 0,8€/m3 of wastewater, a value considered low, attending to the prices of other treatment processes.

Polyimide and polyetherimide organic solvent nanofiltration membranes

Integrally asymmetric skinned Lenzing P84 and Matrimid 5218 polymide membranes and Ultem 1000 polyetherimide membranes were prepared. Crosslinking of membranes using aliphatic diamines resulted in marked improvement in chemical stability. This however resulted in a decline in flux with only Lenzing P84 demonstrating good flux in DMF. Further variation of membrane dope parameters and operating conditions allowed for good control of the MWCO of membranes made from Lenzing P84. SEM pictures of Lenzing P84 membranes revealed a significant difference in membranes morphology. The presence of macrovoids increased when using more DMF in the dope solution. These studies demonstrate the possibility of developing OSN membranes using different polyimides and opens up future possibilities for controlling the MWCO of these membranes. Preliminary modelling demonstrates that good control of the MWCO could extend the application of OSN membranes to allow the fraction of molecules in the NF range.

Development of Chitosan and Poly (Vinyl Alcohol) Blended scaffolds for cell culture using supercritical fluids technology

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Mestrado Integrado em Engenharia Química e Bioquímica

Production of recombinant protein hLIF in static and dynamic systems of animal cell culture

Thesis for the Degree of Master of Science in Biotechnology Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

tlCell: a software transactional memory for the cell broadband engine architecture

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para a obtenção do Grau de Mestre em Engenharia Informática