Pre-treatment of different types of lignocellulosic biomass using ionic liquids

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau Mestre em Biotecnologia

Modelling of a wastewater treatment plant using GPS-X

Dissertation to obtain the degree of Master in Chemical and Biochemical Engineering

Ionic liquids as catalysts of lignocellulosic biomass processing

The present work is devoted to study the pre-treatment of lignocellulosic biomass, especially wheat straw, by the application of the acidic ionic liquid (IL) such as 1-butyl-3-methylimidazolium hydrogen sulphate. The ability of this IL to hydrolysis and conversion of biomass was scrutinised. The pre-treatment with hydrogen sulphate-based IL allowed to obtain a liquor rich in hemicellulosic sugars, furans and organic acids, and a solid fraction mainly constituted by cellulose and lignin. Quantitative and qualitative analyses of the produced liquors were made by capillary electrophoresis and high-performance liquid chromatography. Pre-treatment conditions were set to produce xylose or furfural. Specific range of temperatures from 70 to 175 °C and residence times from 20.0 to 163.3 min were studied by fixing parameters such as biomass/IL ratio (10 % (w/w)) and water content (1.25 % (w/w)) in the pre-treatment process. Statistical modelling was applied to maximise the xylose and furfural concentrations. For the purpose of reaction condition comparison the severity factor for studied ionic liquid was proposed and applied in this work. Optimum conditions for xylose production were identified to be at 125 °C and 82.1 min, at which 16.7 % (w/w) xylose yield was attained. Furfural was preferably formed at higher pre-treatment temperatures and longer reaction time (161 °C and 104.5 min) reaching 30.7 % (w/w) maximum yield. The influence of water content on the optimum xylose formation was also studied. Pre-treatments with 5 and 10 % (w/w) water content were performed and an increase of 100 % and 140 % of xylose yield was observed, respectively, while the conversion into furfural maintained unchanged.

Valorization of grape pomace through hot compressed water extraction/hydrolysis

The world energy consumption is expected to increase strongly in coming years, because of the emerging economies. Biomass is the only renewable carbon resource that is abundant enough to be used as a source of energy Grape pomace is one of the most abundant agro-industrial residues in the world, being a good biomass resource. The aim of this work is the valorization of grape pomace from white grapes (WWGP) and from red grapes (RWGP), through the extraction of phenolic compounds with antioxidant activity, as well as through the extraction/hydrolysis of carbohydrates, using subcritical water, or hot compressed water (HCW). The main focus of this work is the optimization of the process for WWGP, while for RWGP only one set of parameters were tested. The temperatures used were 170, 190 and 210 °C for WWGP, and 180 °C for RWGP. The water flow rates were 5 and 10 mL/min, and the pressure was always kept at 100 bar. Before performing HCW assays, both residues were characterized, revealing that WWGP is very rich in free sugars (around 40%) essentially glucose and fructose, while RWGP has higher contents of structural sugars, lignin, lipids and protein. For WWGP the best results were achieved at 210 °C and 10 mL/min: higher yield in water soluble compounds (69 wt.%), phenolics extraction (26.2 mg/g) and carbohydrates recovery (49.3 wt.% relative to the existing 57.8%). For RWGP the conditions were not optimized (180 °C and 5 mL/min), and the values of the yield in water soluble compounds (25 wt.%), phenolics extraction (19.5 mg/g) and carbohydrates recovery (11.4 wt.% relative to the existing 33.5%) were much lower. The antioxidant activity of the HCW extracts from each assay was determined, the best result being obtained for WWGP, namely for extracts obtained at 210 °C (EC50=20.8 μg/mL; EC50 = half maximum effective concentration; EC50 = 22.1 μg/mL for RWGP, at 180 ºC).

Cellulose-based composites as functional conductive materials for printed electronics

In this work, cellulose-based electro and ionic conductive composites were developed for application in cellulose based printed electronics. Electroconductive inks were successfully formulated for screen-printing using carbon fibers (CFs) and multi-walled carbon nanotubes (MWCNTs) as conductive functional material and cellulose derivatives working as binder. The formulated inks were used to fabricate conductive flexible and disposable electrodes on paper-based substrates. Interesting results were obtained after 10 printing passes and drying at RT of the ink with 10 % wt. of pristine CFs and 3% wt. of carboxymethyl cellulose (CMC), exhibiting a resistivity of 1.03 Ωcm and a resolution of 400 μm. Also, a resistivity of 0.57 Ωcm was obtained for only one printing pass using an ink based on 0.5 % wt. MWCNTs and 3 % wt. CMC. It was also demonstrated that ionic conductive cellulose matrix hydrogel can be used in electrolyte-gated transistors (EGTs). The electrolytes revealed a double layer capacitance of 12.10 μFcm-2 and ionic conductivity of 3.56x10-7 Scm-1. EGTs with a planar configuration, using sputtered GIZO as semiconducting layer, reached an ON/OFF ratio of 3.47x105, a VON of 0.2 V and a charge carrier mobility of 2.32 cm2V-1s-1.