Nestle's dynamic forecasting process: Anticipating risks and opportunities

Nestlé’s Dynamic Forecasting Process: Anticipating Risks and Opportunities This Work Project discusses the Nestlé’s Dynamic Forecasting Process, implemented within the organization as a way of reengineering its performance management concept and processes, so as to make it more flexible and capable to react to volatile business conditions. When stressing the importance of demand planning to reallocate resources and enhance performance, Nescafé Dolce Gusto comes as way of seeking improvements on this forecasts’ accuracy and it is thus, by providing a more accurate model on its capsules’ sales, as well as recommending adequate implementations that positively contribute to the referred Planning Process, that value is brought to the Project

Antioxidant extraction process for Andean Oca by a photodiode array detector using response surface methodology

Application of Experimental Design techniques has proven to be essential in various research fields, due to its statistical capability of processing the effect of interactions among independent variables, known as factors, in a system’s response. Advantages of this methodology can be summarized in more resource and time efficient experimentations while providing more accurate results. This research emphasizes the quantification of 4 antioxidants extraction, at two different concentration, prepared according to an experimental procedure and measured by a Photodiode Array Detector. Experimental planning was made following a Central Composite Design, which is a type of DoE that allows to consider the quadratic component in Response Surfaces, a component that includes pure curvature studies on the model produced. This work was executed with the intention of analyzing responses, peak areas obtained from chromatograms plotted by the Detector’s system, and comprehending if the factors considered – acquired from an extensive literary review – produced the expected effect in response. Completion of this work will allow to take conclusions regarding what factors should be considered for the optimization studies of antioxidants extraction in a Oca (Oxalis tuberosa) matrix.

Development and application of NMR techniques to study water-in-CO2 microemulsions

Self-assembly is a phenomenon that occurs frequently throughout the universe. In this work, two self-assembling systems were studied: the formation of reverse micelles in isooctane and in supercritical CO2 (scCO2), and the formation of gels in organic solvents. The goal was the physicochemical study of these systems and the development of an NMR methodology to study them. In this work, AOT was used as a model molecule both to comprehensively study a widely researched system water/AOT/isooctane at different water concentrations and to assess its aggregation in supercritical carbon dioxide at different pressures. In order to do so an NMR methodology was devised, in which it was possible to accurately determine hydrodynamic radius of the micelle (in agreement with DLS measurements) using diffusion ordered spectroscopy (DOSY), the micellar stability and its dynamics. This was mostly assessed by 1H NMR relaxation studies, which allowed to determine correlation times and size of correlating water molecules, which are in agreement with the size of the shell that interacts with the micellar layer. The encapsulation of differently-sized carbohydrates was also studied and allowed to understand the dynamics and stability of the aggregates in such conditions. A W/CO2 microemulsion was prepared using AOT and water in scCO2, with ethanol as cosurfactant. The behaviour of the components of the system at different pressures was assessed and it is likely that above 130 bar reverse microemulsions were achieved. The homogeneity of the system was also determined by NMR. The formation of the gel network by two small molecular organogelators in toluene-d8 was studied by DOSY. A methodology using One-shot DOSY to perform the spectra was designed and applied with success. This yielded an understanding about the role of the solvent and gelator in the aggregation process, as an estimation of the time of gelation.

Analysis of chromium behaviour and speciation during the electrodialytic process

The interest in chromium (Cr) arises from the widespread use of this heavy metal in various industrial processes that cause its release as liquid, solid and gaseous waste into the environment. The impact of Cr on the environment and living organisms primarily depends on its chemical form, since Cr(III) is an essential micronutrient for humans, other animals and plants, and Cr(VI) is highly toxic and a known human carcinogen. This study aimed to evaluate if the electrodialytic process (ED) is an appropriate treatment for Cr removal, through a critical overview of Cr speciation, before and after the ED experiments, to assess possible Cr(III)-Cr(VI) interconversions during the treatment. ED was the treatment technique applied to two types of matrices containing Cr: chromate copper arsenate (CCA) contaminated soil and municipal solid waste incineration (MSWI) fly ash. In order to study Cr remediation, three EDR set-ups were used: a new set-up, the combined cell (2/3C or 3/2C), with three compartments, alternating current between two anodes and different initial experimental conditions, one set-up with three compartments (3C cell) and the other set-up with two compartments (2C cell). The Cr removal rates obtained in this study were between 10-36% for the soil, and 1-13% for the fly ash. The highest Cr removal rates were achieved in the 26 days experiments: 36% for the soil, 13% for the fly ash. Regarding the 13 days experiments, the highest Cr removal rates were attained with the 2/3C set-up: 24% for the soil, 5% for the fly ash. The analysis of Cr(VI) was performed before and after ED experiments to evaluate eventual changes in Cr speciation during the treatment. This analysis was conducted by two methods: USEPA Method 3060A, for the extraction of Cr(VI); and Hach Company Method 8023, for the detection of Cr(VI). Despite the differences in Cr total concentration, both matrices presented a similar speciation, with Cr(III) being the main species found and Cr(VI) less than 3% of Cr total, before and after the treatment. For fly ash, Cr(VI) was initially below the detection limit of the method and remained that way after the treatment. For soil, Cr(VI) decreased after the treatment. Oxidation of Cr(III) to Cr(VI) did not occur during the ED process since there was no increase in Cr(VI) in the matrices after the treatment. Hence, the results of this study indicate that ED is an appropriate technique to remediate matrices containing Cr because it contributes to Cr removal, without causing Cr(III)-Cr(VI) interconversions.

Development of process control strategies exploiting knowledge from systems biology: application to MDCK suspension cells

Madine Darby Canine Kidney (MDCK) cell lines have been extensively evaluated for their potential as host cells for influenza vaccine production. Recent studies allowed the cultivation of these cells in a fully defined medium and in suspension. However, reaching high cell densities in animal cell cultures still remains a challenge. To address this shortcoming, a combined methodology allied with knowledge from systems biology was reported to study the impact of the cell environment on the flux distribution. An optimization of the medium composition was proposed for both a batch and a continuous system in order to reach higher cell densities. To obtain insight into the metabolic activity of these cells, a detailed metabolic model previously developed by Wahl A. et. al was used. The experimental data of four cultivations of MDCK suspension cells, grown under different conditions and used in this work came from the Max Planck Institute, Magdeburg, Germany. Classical metabolic flux analysis (MFA) was used to estimate the intracellular flux distribution of each cultivation and then combined with partial least squares (PLS) method to establish a link between the estimated metabolic state and the cell environment. The validation of the MFA model was made and its consistency checked. The resulted PLS model explained almost 70% of the variance present in the flux distribution. The medium optimization for the continuous system and for the batch system resulted in higher biomass growth rates than the ones obtained experimentally, 0.034 h-1 and 0.030 h-1, respectively, thus reducing in almost 10 hours the duplication time. Additionally, the optimal medium obtained for the continuous system almost did not consider pyruvate. Overall the proposed methodology seems to be effective and both proposed medium optimizations seem to be promising to reach high cell densities.

Optimization of wastewater quality in the Sines refinery

In order to address and resolve the wastewater contamination problem of the Sines refinery with the main objective of optimizing the quality of this stream and reducing the costs charged to the refinery, a dynamic mass balance was developed nd implemented for ammonia and polar oil and grease (O&G) contamination in the wastewater circuit. The inadequate routing of sour gas from the sour water stripping unit and the kerosene caustic washing unit, were identified respectively as the major source of ammonia and polar substances present in the industrial wastewater effluent. For the O&G content, a predictive model was developed for the kerosene caustic washing unit, following the Projection to Latent Structures (PLS) approach. Comparison between analytical data for ammonia and polar O&G concentrations in refinery wastewater originating from the Dissolved Air Flotation (DAF) effluent and the model predictions of the dynamic mass balance calculations are in a very good agreement and highlights the dominant impact of the identified streams for the wastewater contamination levels. The ammonia contamination problem was solved by rerouting the sour gas through an existing clogged line with ammonia salts due to a non-insulated line section, while for the O&G a dynamic mass balance was implemented as an online tool, which allows for prevision of possible contamination situations and taking the required preventive actions, and can also serve as a basis for establishing relationships between the O&G contamination in the refinery wastewater with the properties of the refined crude oils and the process operating conditions. The PLS model developed could be of great asset in both optimizing the existing and designing new refinery wastewater treatment units or reuse schemes. In order to find a possible treatment solution for the spent caustic problem, an on-site pilot plant experiments for NaOH recovery from the refinery kerosene caustic washing unit effluent using an alkaline-resistant nanofiltration (NF) polymeric membrane were performed in order to evaluate its applicability for treating these highly alkaline and contaminated streams. For a constant operating pressure and temperature and adequate operating conditions, 99.9% of oil and grease rejection and 97.7% of chemical oxygen demand (COD) rejection were observed. No noticeable membrane fouling or flux decrease were registered until a volume concentration factor of 3. These results allow for NF permeate reuse instead of fresh caustic and for significant reduction of the wastewater contamination, which can result in savings of 1.5 M€ per year at the current prices for the largest Portuguese oil refinery. The capital investments needed for implementation of the required NF membrane system are less than 10% of those associated with the traditional wet air oxidation solution of the spent caustic problem. The operating costs are very similar, but can be less than half if reusing the NF concentrate in refinery pH control applications. The payback period was estimated to be 1.1 years. Overall, the pilot plant experimental results obtained and the process economic evaluation data indicate a very competitive solution through the proposed NF treatment process, which represents a highly promising alternative to conventional and existing spent caustic treatment units.

On the labor share the long-run equilibrium and its adjustment process

This research computes an Equilibrium Labor Share using a VECM for a panel of 19 countries, analyzes what determines the speed at which the labor share adjusts towards that equilibrium and decomposes this adjustment in terms of real wages and employment. Results suggest that the speed at which a country adjusts decreases with employment protection legislation and labor taxes. Most countries’ labor shares adjustment is made through real wages changes instead of changing employment, suggesting that wage moderation policies may play an important role on the adjustment process without harming employment. Keywords: Equilibrium

On the labor share the long-run equilibrium and its adjustment process

This research computes an Equilibrium Labor Share using a VECM for a panel of 19 countries, analyzes what determines the speed at which the labor share adjusts towards that equilibrium and decomposes this adjustment in terms of real wages and employment. Results suggest that the speed at which a country adjusts decreases with employment protection legislation and labor taxes. Most countries’ labor shares adjustment is made through real wages changes instead of changing employment, suggesting that wage moderation policies may play an important role on the adjustment process without harming employment.

Analysis of a controversial decision process: the case of the pumped hydro storage power plant Atdorf in Germany

Based on the report for the unit “Métodos Interactivos de Participação e Decisão A” (Interactive methods of participation and decision A), coordinated by Prof. Lia Maldonado Teles de Vasconcelos and Prof. Nuno Miguel Ribeiro Videira Costa. This unit was provided for the PhD Program in Technology Assessment in 2015/2016.

Relatório de estágio na Caixa Geral de Depósitos

This report will describe the activities undertaken during my internship at the Personnel Department (DPE-UPE4.1) in Caixa Geral de Depósitos (CGD), Lisbon, between September 22, 2014, and February 28, 2015. I consider that it is important to note from the outset i) that the subject of my training was suggested by my supervisor in the DPE and accepted by me; and ii) that the internship consisted essentially of carrying out research and information gathering into the different social systems that coexist within the bank and the application of each legal system in solving concrete situations of the CGD employees. The research and analysis of information was important not only for my study but for the CGD itself, as it enables the department to have such an important matter, full of specific characteristics, condensed into a single document, i.e. this report. This is a complex reality. The various welfare systems differ according to the contractual agreement linking the employee to the employer at the date when the labour contract is signed, and also the unique/singular characteristics of the CGD. In the early stage I started by trying to understand the financial institution and its organization and role and the department where I worked. So I analyzed the CGD Statutes and the legal measures that crystallized the scheme for its employees and I also researched its domestic and international operations. The first month was devoted to the research and analysis of such legislation to understand the creation of the CGD and its path to date. In the second and third months I studied the legal social systems that are applied to different groups of CGD workers. This period was quite important to identify and understand the differences between those regimes of CGD employees as well as the procedure inherent in each case. I highlighted the non-implementation of “the social protection regime of convergence” to the workers of this institution; the differences regarding the allocation of sickness subsidies paid to workers who belong to Social Security and CGA contributors, as well as the enforcement of internal rules to all the workers when a work-related accident happens.Then I focused on to assessing and examining external legislation and several internal regulations in order to obtain solutions to questions raised and situations involving by the workers, in order to understand how the DPE solves these situations. Over the last three months of internship, after this more theoretical work, I began the analysis of concrete situations involving employees carrying out their duties in Portugal and abroad. Some of these situations had been received by the department before the beginning of my internship and others over this period. When I was “working” in the DPE I analyzed “cases” that had been solved and some others without a final solution because they were still in courts. As for the last ones (new cases) I was able to follow their assessment and sometimes their outcome. Some of them became study cases for me. Over these five months of my internship, several cases were analyzed and discussed by legal experts of DPE in which I could participate. I always worked hard. I know that this action contributed to elucidate me about the treatment of the issues, and allowed me to have a direct contact with some workers and be part of a dynamic work team. For these reasons, my internship report is not merely descriptive of activities. It consists of an analysis of rules (legislation) and a regulatory framework of activities and it is also a description of several specific situations solved or in a solution process. Through this work I intend to make known the particular reality of a modern Portuguese financial institution not only because of its importance in our country but also such a large number of employees work here (in Portugal and abroad). I should add that throughout my internship I was allowed to attend conferences, within the scope of the bank in order to get a broader view of some issues related to the daily life of the DPE and the CGD. So, I participated in I Jornadas Bancárias and the Conferência Internacional do Contrato a Termo, given that the CGD is a bank and the DPE deals with legal and labour relations.

Millennium BCP: Optimization of the branches closure process

Nowadays, a significant number of banks in Portugal are facing a bank-branch restructuring problem, and Millennium BCP is not an exception. The closure of branches is a major component of profit maximization through the reduction in operational and personnel costs but also an opportunity to approach the idea of “baking of future” and start thinking on the benefits of the digital era. This dissertation centers on a current high-impact organizational problem addressed by the company and consists in a proposal of optimization to the model that Millennium BCP uses. Even though measures of performance are usually considered the most important elements in evaluating the viability of branches, there is evidence suggesting that other general factors can be important to assess branch potential, such as the influx on branches, business dimensions of a branch and its location, which will be addressed in this project.

Assessing fraud risk of selecção, contratação e manutenção de fornecedores process of Sonae Investimentos

The present Work Project (WP) is the result of Sonae’s concern with fraud risk, seeking to implement a method that formally describes and evaluates it in its various forms. In a context of limited human, capital, time and tools’ resources, the Internal Audit (IA) department of the company developed a framework to raise the awareness of top management and identify which processes of its value chain present a higher level of exposure to fraud, with the purpose of redirecting attention to those and prioritizing the creation of new mechanisms to monitor its KPIs’ dynamics.

Proving a market for a startup befor scaling using the hypothesis-driven entrepreneurship process

The year is 2015 and the startup and tech business ecosphere has never seen more activity. In New York City alone, the tech startup industry is on track to amass $8 billion dollars in total funding – the highest in 7 years (CB Insights, 2015). According to the Kauffman Index of Entrepreneurship (2015), this figure represents just 20% of the total funding in the United States. Thanks to platforms that link entrepreneurs with investors, there are simply more funding opportunities than ever, and funding can be initiated in a variety of ways (angel investors, venture capital firms, crowdfunding). And yet, in spite of all this, according to Forbes Magazine (2015), nine of ten startups will fail. Because of the unpredictable nature of the modern tech industry, it is difficult to pinpoint exactly why 90% of startups fail – but the general consensus amongst top tech executives is that “startups make products that no one wants” (Fortune, 2014). In 2011, author Eric Ries wrote a book called The Lean Startup in attempts to solve this all-too-familiar problem. It was in this book where he developed the framework for The Hypothesis-Driven Entrepreneurship Process, an iterative process that aims at proving a market before actually launching a product. Ries discusses concepts such as the Minimum Variable Product, the smallest set of activities necessary to disprove a hypothesis (or business model characteristic). Ries encourages acting briefly and often: if you are to fail, then fail fast. In today’s fast-moving economy, an entrepreneur cannot afford to waste his own time, nor his customer’s time. The purpose of this thesis is to conduct an in-depth of analysis of Hypothesis-Driven Entrepreneurship Process, in order to test market viability of a reallife startup idea, ShowMeAround. This analysis will follow the scientific Lean Startup approach; for the purpose of developing a functional business model and business plan. The objective is to conclude with an investment-ready startup idea, backed by rigorous entrepreneurial study.