Genome-scale metabolic network reconstruction of Polaromonas sp. strain JS666: analysis of cDCE degradation rates and design of experiments for bioremediation improvement

Release of chloroethene compounds into the environment often results in groundwater contamination, which puts people at risk of exposure by drinking contaminated water. cDCE (cis-1,2-dichloroethene) accumulation on subsurface environments is a common environmental problem due to stagnation and partial degradation of other precursor chloroethene species. Polaromonas sp. strain JS666 apparently requires no exotic growth factors to be used as a bioaugmentation agent for aerobic cDCE degradation. Although being the only suitable microorganism found capable of such, further studies are needed for improving the intrinsic bioremediation rates and fully comprehend the metabolic processes involved. In order to do so, a metabolic model, iJS666, was reconstructed from genome annotation and available bibliographic data. FVA (Flux Variability Analysis) and FBA (Flux Balance Analysis) techniques were used to satisfactory validate the predictive capabilities of the iJS666 model. The iJS666 model was able to predict biomass growth for different previously tested conditions, allowed to design key experiments which should be done for further model improvement and, also, produced viable predictions for the use of biostimulant metabolites in the cDCE biodegradation.

Relatório de estágio na agência Ogilvy. A importância dos testes de usabilidade e do Responsive Web Design no desenvolvimento de projetos digitais

O presente relatório de estágio enquadra-se no método de avaliação final do Mestrado em Novos Media e Práticas Web, da Faculdade de Ciências Sociais e Humanas da Universidade Nova de Lisboa e pretende abordar o trabalho desenvolvido por mim durante o estágio curricular realizado na agência de comunicação e publicidade Ogilvy. O estágio decorreu entre novembro de 2014 e fevereiro de 2015, durante o qual desempenhei o cargo de online producer e fui supervisionada por Sara Cabral Fonseca, diretora de projeto. Todos os trabalhos tiveram como objetivo principal o acompanhamento e conhecimento do processo ligado ao desenvolvimento de projetos digitais, desde o briefing até à programação e conteúdo. Os trabalhos compreenderam a realização de testes de usabilidade em deskop e mobile dos sites e aplicações desenvolvidos pelo departamento digital da empresa, e também o apoio na realização de tarefas ligadas à gestão de conteúdos de vários websites. Este relatório resulta de todo o trabalho concretizado e pretende efetuar uma contextualização teórica ligada à importância dos testes de usabilidade e do Responsive Web Design (RWD) na implementação de projetos digitais.

Optimisation and design of post-tensioning anchorage corner blisters in concrete box girder bidges

The design of anchorage blisters of internal continuity post-tensioning tendons of bridges built by the cantilever method, presents some peculiarities, not only because they are intermediate anchorages but also because these anchorages are located in blisters, so the prestressing force has to be transferred from the blister the bottom slab and web of the girder. The high density of steel reinforcement in anchorage blisters is the most common reason for problems with concrete cast in situ, resulting in zones with low concrete compacity, leading to concrete crushing failures under the anchor plates. A solution may involve improving the concrete compression and tensile strength. To meet these requirements a high-performance fibre reinforced self-compacting mix- ture (HPFRC) was used in anchorage corner blisters of post-tensioning tendons, reducing the concrete cross-section and decreasing the reinforcement needed. To assess the ultimate capacity and the adequate serviceability of the local anchorage zone after reducing the minimum concrete cross-section and the confining reinforcement, specified by the anchorage device supplier for the particular tendon, load transfer tests were performed. To investigate the behaviour of anchorage blisters regarding the transmission of stresses to the web and the bottom slab of the girder, and the feasibility of using high performance concrete only in the blister, two half scale models of the inferior corner of a box girder existing bridge were studied: a reference specimen of ordinary reinforced concrete and a HPFRC blister specimen. The design of the reinforcement was based in the tensile forces obtained on strut-and-tie models. An experimental program was carried out to assess the models used in design and to study the feasibility of using high performance concrete only in the blister, either with casting in situ, or with precast solutions. A non-linear finite element analysis of the tested specimens was also performed and the results compared.

Towards modification of Medicago truncatula epigenome: genome editing with engineered nucleases

Periodic drought is the primary limitation of plant growth and crop yield. The rise of water demand caused by the increase in world population and climate change, leads to one of the biggest challenges of modern agriculture: to increase food and feed production. De novo DNA methylation is a process regulated by small interfering RNA (siRNAs), which play a role in plant response and adaptation to abiotic stress. In the particular case of water deficit, growing evidences suggest a link between the siRNA pathways and drought response in the model legume Medicago truncatula. As a first step to understand the role of DNA methylation under water stress, we have set up several bioinformatics and molecular methodologies allowing the design of Clustered regularly interspaced short palindromic repeats (CRISPR)/Cas9 systems and the assembly of TALENs (transcription activator-like effector nucleases), to target both dicer-like 3 (MtDCL3) and RNA-Dependent RNA polymerase (MtRDR2), enzymes of the RNA-directed DNA methylation pathway. TALENs efficiency was evaluated prior to plant transformation by a yeast-based assay using two different strategies to test TALENs activity: Polyacrylamide gel electrophoresis (PAGE) and Single strand conformation polymorphisms (SSCP). In this assay, yeast cells triple transformation emerged as good and rapid alternative to laborious yeast mating strategies. PAGE analysis might be a valuable tool to test TALENs efficacy in vivo if we could increase TALENs activity. SSCP-based approach proved to be ineffective due to the generation of several false positives. TALENs and CRISPR/Cas9 system constructed and designed in this work will in the future certainly enable the successful disruption of DCL3 and RDR2 genes and shed the light on the relationship between plant stress resistance and epigenetic regulation mediated by siRNAs in M.truncatula.

Production and characterization of electrospun composite fibers: confinement of thermosensitive microgels

Materials engineering focuses on the assembly of materials´ properties to design new products with the best performance. By using sub-micrometer size materials in the production of composites, it is possible to obtain objects with properties that none of their compounds show individually. Once three-dimensional materials can be easily customized to obtain desired properties, much interest has been paid to nanostructured poly-mers in order to build biocompatible devices. Over the past years, the thermosensitive microgels have become more common in the framework of bio-materials with potential applicability in therapy and/or diagnostics. In addition, high aspect ratio biopolymers fibers have been produced using the cost-effective method called electrospinning. Taking advantage of both microgels and electrospun fibers, surfaces with enhanced functionalities can be obtained and, therefore employed in a wide range of applications. This dissertation reports on the confinement of stimuli-responsive microgels through the colloidal electro-spinning process. The process mainly depends on the composition, properties and patterning of the precur-sor materials within the polymer jet. Microgels as well as the electrospun non-woven mats were investigated to correlate the starting materials with the final morphology of the composite fibers. PNIPAAm and PNIPAAm/Chitosan thermosensitive microgels with different compositions were obtained via surfactant free emulsion polymerization (SFEP) and characterized in terms of chemical structure, morphology, thermal sta-bility, swelling properties and thermosensitivity. Finally, the colloidal electrospinning method was carried out from spinning solutions composed of the stable microgel dispersions (up to a concentration of about 35 wt. % microgels) and a polymer solution of PEO/water/ethanol mixture acting as fiber template solution. The confinement of microgels was confirmed by Scanning Electron Microscopy (SEM). The electrospinning process was statistically analysed providing the optimum set of parameters aimed to minimize the fiber diameter, which give rise to electrospun nanofibers of PNIPAAm microgels/PEO with a mean fiber diameter of 63 ± 25 nm.

Proposal of a methodology for the design of the installation of turrets on aircrafts – the approach on the aerodynamic influences

The present work has its origin on the necessity of enabling a design certified company, or DOA (Design Organization Approval), to perform a modification; this modification is the installation of EO/IR (Electro-optical infrared) sensors on aircrafts. The subject of interest in this dissertation lies on the aerodynamic impact of the modification on the aircraft. The primary purpose of the present thesis is the creation of a methodology that regards the design stage of the modification. This methodology serves as guidance to the DOA design team that is assigned to the design of the modification. The methodology includes a recommendation to the certification of the modification; it contains a method intended to decide the location of the installation of the sensors on the aircraft; it also comprises of a design structure specifically adapted to the modification in study. Regarding the aerodynamic impact, it is studied the aerodynamic analysis’ tools, which allows one to relate the different stages of design to the most suited tools to each stage. A case study is performed with the purpose of not only validating the methodology which was created but also to giving a first approach to the preliminary design of the modification. As example, there are used the Lockheed Martin C-130 aircraft and the FLIR Star Safire III sensor.

Analysis and design of sinusoidal quadrature RC-oscillators

Modern telecommunication equipment requires components that operate in many different frequency bands and support multiple communication standards, to cope with the growing demand for higher data rate. Also, a growing number of standards are adopting the use of spectrum efficient digital modulations, such as quadrature amplitude modulation (QAM) and orthogonal frequency division multiplexing (OFDM). These modulation schemes require accurate quadrature oscillators, which makes the quadrature oscillator a key block in modern radio frequency (RF) transceivers. The wide tuning range characteristics of inductorless quadrature oscillators make them natural candidates, despite their higher phase noise, in comparison with LC-oscillators. This thesis presents a detailed study of inductorless sinusoidal quadrature oscillators. Three quadrature oscillators are investigated: the active coupling RC-oscillator, the novel capacitive coupling RCoscillator, and the two-integrator oscillator. The thesis includes a detailed analysis of the Van der Pol oscillator (VDPO). This is used as a base model oscillator for the analysis of the coupled oscillators. Hence, the three oscillators are approximated by the VDPO. From the nonlinear Van der Pol equations, the oscillators’ key parameters are obtained. It is analysed first the case without component mismatches and then the case with mismatches. The research is focused on determining the impact of the components’ mismatches on the oscillator key parameters: frequency, amplitude-, and quadrature-errors. Furthermore, the minimization of the errors by adjusting the circuit parameters is addressed. A novel quadrature RC-oscillator using capacitive coupling is proposed. The advantages of using the capacitive coupling are that it is noiseless, requires a small area, and has low power dissipation. The equations of the oscillation amplitude, frequency, quadrature-error, and amplitude mismatch are derived. The theoretical results are confirmed by simulation and by measurement of two prototypes fabricated in 130 nm standard complementary metal-oxide-semiconductor (CMOS) technology. The measurements reveal that the power increase due to the coupling is marginal, leading to a figure-of-merit of -154.8 dBc/Hz. These results are consistent with the noiseless feature of this coupling and are comparable to those of the best state-of-the-art RC-oscillators, in the GHz range, but with the lowest power consumption (about 9 mW). The results for the three oscillators show that the amplitude- and the quadrature-errors are proportional to the component mismatches and inversely proportional to the coupling strength. Thus, increasing the coupling strength decreases both the amplitude- and quadrature-errors. With proper coupling strength, a quadrature error below 1° and amplitude imbalance below 1% are obtained. Furthermore, the simulations show that increasing the coupling strength reduces the phase noise. Hence, there is no trade-off between phase noise and quadrature error. In the twointegrator oscillator study, it was found that the quadrature error can be eliminated by adjusting the transconductances to compensate the capacitance mismatch. However, to obtain outputs in perfect quadrature one must allow some amplitude error.

Medium access control design for distributed opportunistic radio networks

Existing wireless networks are characterized by a fixed spectrum assignment policy. However, the scarcity of available spectrum and its inefficient usage demands for a new communication paradigm to exploit the existing spectrum opportunistically. Future Cognitive Radio (CR) devices should be able to sense unoccupied spectrum and will allow the deployment of real opportunistic networks. Still, traditional Physical (PHY) and Medium Access Control (MAC) protocols are not suitable for this new type of networks because they are optimized to operate over fixed assigned frequency bands. Therefore, novel PHY-MAC cross-layer protocols should be developed to cope with the specific features of opportunistic networks. This thesis is mainly focused on the design and evaluation of MAC protocols for Decentralized Cognitive Radio Networks (DCRNs). It starts with a characterization of the spectrum sensing framework based on the Energy-Based Sensing (EBS) technique considering multiple scenarios. Then, guided by the sensing results obtained by the aforementioned technique, we present two novel decentralized CR MAC schemes: the first one designed to operate in single-channel scenarios and the second one to be used in multichannel scenarios. Analytical models for the network goodput, packet service time and individual transmission probability are derived and used to compute the performance of both protocols. Simulation results assess the accuracy of the analytical models as well as the benefits of the proposed CR MAC schemes.

Electro-Optical/Infrared sensor turret integration on an aircraft - structural im-pact on LOCKHEED MARTIN C-130H and design methodology

The growing need to patrol and survey large maritime and terrestrial areas increased the need to integrate external sensors on aircraft in order to accomplish those patrols at increasingly higher altitudes, longer range and not depending upon vehicle type. The main focus of this work is to elaborate a practical, simple, effective and efficient methodology for the aircraft modification procedure resulting from the integration of an Elec-tro-Optical/Infra-Red (EO/IR) turret through a support structure. The importance of the devel-opment of a good methodology relies on the correct management of project variables as time, available resources and project complexity. The key is to deliver a proper tool for a project de-sign team that will be used to create a solution that fulfils all technical, non-technical and certi-fication requirements present in this field of transportation. The created methodology is inde-pendent of two main inputs: sensor model and aircraft model definition, and therefore it is in-tended to deliver the results for different projects besides the one that was presented in this work as a case study. This particular case study presents the development of a structure support for FLIR STAR SAPHIRE III turret integration on the front lower fuselage bulkhead (radome) of the LOCKHEED MARTIN C-130 H. Development of the case study focuses on the study of local structural analysis through the use of Finite Element Method (FEM). Development of this Dissertation resulted in a cooperation between Faculty of Science and Technology - Universidade Nova de Lisboa and the company OGMA - Indústria Aeronáutica de Portugal

A systematic methodology to analyse the performance and design configurations of business interoperability in cooperative industrial networks

This thesis proposes a methodology for modelling business interoperability in a context of cooperative industrial networks. The purpose is to develop a methodology that enables the design of cooperative industrial network platforms that are able to deliver business interoperability and the analysis of its impact on the performance of these platforms. To achieve the proposed objective, two modelling tools have been employed: the Axiomatic Design Theory for the design of interoperable platforms; and Agent-Based Simulation for the analysis of the impact of business interoperability. The sequence of the application of the two modelling tools depends on the scenario under analysis, i.e. whether the cooperative industrial network platform exists or not. If the cooperative industrial network platform does not exist, the methodology suggests first the application of the Axiomatic Design Theory to design different configurations of interoperable cooperative industrial network platforms, and then the use of Agent-Based Simulation to analyse or predict the business interoperability and operational performance of the designed configurations. Otherwise, one should start by analysing the performance of the existing platform and based on the achieved results, decide whether it is necessary to redesign it or not. If the redesign is needed, simulation is once again used to predict the performance of the redesigned platform. To explain how those two modelling tools can be applied in practice, a theoretical modelling framework, a theoretical Axiomatic Design model and a theoretical Agent-Based Simulation model are proposed. To demonstrate the applicability of the proposed methodology and/or to validate the proposed theoretical models, a case study regarding a Portuguese Reverse Logistics cooperative network (Valorpneu network) and a case study regarding a Portuguese construction project (Dam Baixo Sabor network) are presented. The findings of the application of the proposed methodology to these two case studies suggest that indeed the Axiomatic Design Theory can effectively contribute in the design of interoperable cooperative industrial network platforms and that Agent-Based Simulation provides an effective set of tools for analysing the impact of business interoperability on the performance of those platforms. However, these conclusions cannot be generalised as only two case studies have been carried out. In terms of relevance to theory, this is the first time that the network effect is addressed in the analysis of the impact of business interoperability on the performance of networked companies and also the first time that a holistic approach is proposed to design interoperable cooperative industrial network platforms. Regarding the practical implications, the proposed methodology is intended to provide industrial managers a management tool that can guide them easily, and in practical and systematic way, in the design of configurations of interoperable cooperative industrial network platforms and/or in the analysis of the impact of business interoperability on the performance of their companies and the networks where their companies operate.

What do broadband consumers want? Design and execution of a questionnaire on demand for bundled services on the Portuguese telecomunications market

The report addresses the question of what are the preferences of broadband consumers on the Portuguese telecommunication market. A triple play bundle is being investigated. The discrete choice analysis, adopted in the study, base on 110 responses, mainly from NOVA students. The data for the analysis was collected via manually designed on-line survey. The results show that the price attribute is relatively the most important one while the television attribute is being overlooked in the decision making process. Main effects examined in the research are robust. In addition, "extras" components are being tested in terms of users' preferences.

The role of guarantees in pension plan design: Pension saving decisions

This study centers on the assessment of psychological value of guarantees in pension products and the behavior biases associated with choice. When a guarantee on a product increases from 99% to 99,5% less than half of respondents show willingness to pay in contrast with 73% when going from 99,5% to 100%. Out of 105 respondents, 55 show that their choices concerning pension products are inconsistent with classic utility theory. Financial background proves insignificant thus pointing to behavioral biases. As individuals make choices that leave them worse-off, we argue that pension plan design would highly benefit from public policy interventions.

Design and implementation of an assurance map at Sonae retail business

The present Working Project aims at studying the topic of assurance mapping in a specific organizational context of a Portuguese retail company. For this purpose, an assurance map framework was designed to support the decision making process of stakeholders, through the delivery of comfort concerning risks, operations and control. In the end, the framework was successfully implemented for the process sourcing of goods in two business units of the company. Although, further implementation of the framework proved not to be feasible during the project’s timespan, it is expected to occur in the near future.

Design of bio-inspired ionic liquids for protein stabilisation

Ionic Liquids (ILs) consist in organic salts that are liquid at/or near room temperature. Since ILs are entirely composed of ions, the formation of ion pairs is expected to be one essential feature for describing solvation in ILs. In recent years, protein - ionic liquid (P-IL) interactions have been the subject of intensive studies mainly because of their capability to promote folding/unfolding of proteins. However, the ion pairs and their lifetimes in ILs in P-IL thematic is dismissed, since the action of ILs is therefore the result of a subtle equilibrium between anion-cation interaction, ion-solvent and ion-protein interaction. The work developed in this thesis innovates in this thematic, once the design of ILs for protein stabilisation was bio-inspired in the high concentration of organic charged metabolites found in cell milieu. Although this perception is overlooked, those combined concentrations have been estimated to be ~300 mM among the macromolecules at concentrations exceeding 300 g/L (macromolecular crowding) and transient ion-pair can naturally occur with a potential specific biological role. Hence the main objective of this work is to develop new bio-ILs with a detectable ion-pair and understand its effects on protein structure and stability, under crowding environment, using advanced NMR techniques and calorimetric techniques. The choline-glutamate ([Ch][Glu]) IL was synthesized and characterized. The ion-pair was detected in water solutions using mainly the selective NOE NMR technique. Through the same technique, it was possible to detect a similar ion-pair promotion under synthetic and natural crowding environments. Using NMR spectroscopy (protein diffusion, HSQC experiments, and hydrogen-deuterium exchange) and differential scanning calorimetry (DSC), the model protein GB1 (production and purification in isotopic enrichment media) it was studied in the presence of [Ch][Glu] under macromolecular crowding conditions (PEG, BSA, lysozyme). Under dilute condition, it is possible to assert that the [Ch][Glu] induces a preferential hydration by weak and non-specific interactions, which leads to a significant stabilisation. On the other hand, under crowding environment, the [Ch][Glu] ion pair is promoted, destabilising the protein by favourable weak hydrophobic interactions , which disrupt the hydration layer of the protein. However, this capability can mitigates the effect of protein crowders. Overall, this work explored the ion-pair existence and its consequences on proteins in conditions similar to cell milieu. In this way, the charged metabolites found in cell can be understood as key for protein stabilisation.