Upgrade of an experimental volumetric unit for gas adsorption equilibrium studies

In this work, a volumetric unit previously assembled by the research group was upgraded. This unit revamping was necessary due to the malfunction of the solenoid valves employed in the original experimental setup, which were not sealing the gas properly leading to erroneous adsorption equilibrium measurements. Therefore, the solenoid valves were substituted by manual ball valves. After the volumetric unit improvement its operation was validated. For this purpose, the adsorption equilibrium of carbon dioxide (CO2) at 323K and 0 - 20 bar was measured on two different activated carbon samples, in the of extrudates (ANG6) and of a honeycomb monolith (ACHM). The adsorption equilibrium results were compared with data previously measured by the research group, using a high-pressure microbalance from Rubotherm GmbH (Germany) – gravimetric. The results obtained using both apparatuses are coincident thus validating the good operation of the volumetric unit upgraded in this work. Furthermore, the adsorption equilibrium of CO2 at 303K and 0 - 10 bar on Metal-Organic Frameworks (MOFs) Cu-BTC and Fe-BTC was also studied. The CO2 adsorption equilibrium results for both MOFs were compared with the literature results showing good agreement, which confirms the good quality of the experimental results obtained in the new volumetric unit. Cu-BTC sample showed significantly higher CO2 adsorption capacity when compared with the Fe-BTC sample. The revamping of the volumetric unit included a new valve configuration in order to allow testing an alternative method for the measurement of adsorption equilibrium. This new method was employed to measure the adsorption equilibrium of CO2 on ANG6 and ACHM at 303, 323 and 353K within 0-10 bar. The good quality of the obtained experimental data was testified by comparison with data previously obtained by the research group in a gravimetric apparatus.

Double-walled PLLA/PLGA particles for the sustained release of Meloxicam: preparation, characterisation and contolled release studies

There were two main objectives in this thesis investigation, first, the production, characterisation, in vitro degradation and release studies of double walled microspheres for drug release control. The second one, and the most challenging, was the production of double walled nanospheres, also for drug control delivery. The spheres were produced using two polymers, the Poly(L-lactide)Acid, PLLA, and the Poly(L-lactide-co-glycolic)Acid, PLGA.Afterwards, a model drug, Meloxicam, which is an antiinflammatory drug, was encapsulated into the particles. Micro and nanospheres were produced by the solvent extraction/evaporation method, where perfect spherical particles were obtained. By varying the polymers PLLA/PLGA mass ratio, different core and shell composition, as well as several shell and core thickness were observed. In the particles with a PLLA/PLGA mass ratio 1:1, the shell is composed by PLLA and the core by PLGA. It was also verified that the Meloxicam has a tendency to be distributed in the PLGA layer. Micro and nanoparticles were characterised in morphology, size, polymer cristalinity properties and drug distribution. Particles degradation studies was performed, where the particles in a PVA solution of pH 7,4 where placed in an incubator, during approximately 40 days, at 120rpm, and 37ºC, simulating, as much as possible, the human body environment. From these studies, the conclusion was that particles containing a PLGA shell and a PLLA core degrade more rapidly, due to the fact that PLLA is more hydrophobic than the PLGA. Concerning the drug release controlled results, done also for 40 and 50 days, they showed that the microspheres containing a shell of PLLA release more slowly than when the shell is composed of PLGA. This result was predictable, since the drug is solubilised in the PLGA polymer and so, in that case, the PLLA shell works like a barrier between the drug and the outer medium. Another positive aspect presented by this study is the lower initial burst effect, obtained when using double walled particles, which is one of the advantages of the same. In a second part of this investigation, the production of the nanospheres was the main goal, since it was not yet accomplished by other authors or investigators. After several studies, referring to the speed, time and type of agitation, as well as, the concentration and volume of the first aqueous solution of poly-vinyl-alcohol (PVA) during the process of solvent extraction/evaporation it was possible to obtain double walled nanospheres.(...)

Structural and functional studies of a high activity NiFeSe Hydrogenase

Theawareness that fossil fuels exist in limited quantities has stimulated research into energy production from renewable sources. Future energy sources! should! be! plentiful! with! negligible! impact! on! the! environment.! Hydrogen!has!the!potential!to!satisfy!these!requirements.!Nevertheless,!current! methods! of! H2! production! rely! on! nonOrenewable! resources.! Biological! H2! production! from! sunlight! or! biomass! is! an! appealing! alternative! to! current! production!methods.!!(...)

Brucelose na Província do Namibe, Angola, 2012 : prevalências humana (profissionais da pecuária) e animal, factores de risco, conhecimento e práticas

RESUMO - Enquadramento: A Brucelose é uma antropozoonose prevalente no Mundo e é uma das mais negligenciadas. A sua transmissão ao ser humano é directa e indirecta, e acontece por via de contacto com animal infectado, o consumo de leite e seus derivados não pasteurizados e a não observância de uso de equipamentos de protecção individual e colectiva, entre outros factores. O conhecimento da prevalência e incidência da brucelose animal e humana no Namibe, uma província de Angola, é muito escasso sendo poucos os estudos que evidenciam esta doença no seio dos profissionais da pecuária expostos: trabalhadores de matadouros, veterinários e criadores de gado. É assim pertinente, com base em estudos científicos específicos, caracterizar esta situação. Objectivos: Caracterizar os ambientes dos profissionais (matadouro, talhos e salas municipais de abate e explorações); estimar a seroprevalência da brucelose humana em profissionais da pecuária (trabalhadores de matadouros e criadores de gado bovino) na província do Namibe, Angola em 2012; determinar a associação da presença da brucelose humana com variáveis sócio-demográficas, de conhecimento, de práticas e de características das explorações; determinar a prevalência da Brucelose em animais e em explorações; caracterizar os factores associados à presença da Brucelose em explorações bovinas; caracterizar o conhecimento e práticas sobre a Brucelose dos profissionais da pecuária e analisar a relação entre as prevalências nas explorações (infectadas versus não infectadas) e nos criadores (infectados versus não infectados). Métodos e materiais: estudos observacional e transversal seroepidemiológico em 131 trabalhadores de talhos, salas de abate e matadouro e 192 criadores amostrados aleatoriamente em toda província do Namibe. Os dados foram obtidos através da colheita de sangue e da aplicação de um questionário. Os testes laboratoriais utilizados foram o Rosa de Bengala (RBT) e a Aglutinação Lenta em Tubos (SAT). O estudo de conhecimento foi principalmente centrado na pergunta “Já ouviu falar de Brucelose” e nas questões relativas ao nível de conhecimento e práticas (indicadores baseados nas percentagens de respostas correctas ou práticas adequadas) dos factores de risco da Brucelose. Também foram investigados 1344 animais (em 192 explorações) com recurso ao método de diagnóstico laboratorial RBT para análise de soro sanguíneo e, complementarmente, foi aplicado um questionário aos respectivos criadores. Em termos de análise estatística, para além da abordagem descritiva, foram utilizados os testes de Independência do Quiquadrado, Fisher, Teste não paramétrico de Mann-Whitney, Teste de correlação de Spearman. Adicionalmente, com base em modelos de regressão logística, foram determinados odds ratio e os respectivos intervalos de confiança utilizando um nível de significância de 5%. Resultados: os ambientes dos profissionais (matadouro, talhos e salas municipais de abate e explorações) não reuniram as condições higio-sanitárias definidas internacionalmente como adequadas. Nos profissionais a infecção geral ponderada da Brucelose foi de 15.56% (IC95% : 13.61-17.50), sendo 5.34% em trabalhadores e 16.66% (IC95% : 11.39-21.93) em criadores. A significância estatística foi observada entre a seroprevalência humana e a categoria (trabalhador e criador) (p< 0.001) e o nível de instrução (p= 0.032), início de actividade (p= 0.079) e local de serviço (p= 0.055). Num contexto multivariado o factor positivamente associado à brucelose em profissionais foi a categoria profissional (OR = 3.54, IC95%: 1.57-8.30, relativo aos criadores em relação a trabalhadores). As taxas gerais aparentes de prevalência em animais e explorações foram respectivamente de 14.96% (IC 95%, 12.97-17.19) e de 40.10% (IC 95%, 32.75-47.93). Encontrou-se uma correlação positiva moderada entre o número de animais infectados por exploração com a média do número de abortos na exploração = 0.531, p< 0.001). Em média os profissionais tiveram um conhecimento global muito insuficiente (16.1%), tendo os trabalhadores apresentado valores mais elevados que os criadores (20.2% e 13.8%), diferença não estatisticamente significativa (p= 0.170). As perguntas “o leite in natura é fervido antes do consumo humano?”, “contacto com materiais fetais animais?”, “contacto com aerossóis no local de trabalho?” e “já fez alguma vez o teste de Brucelose humana?” (relacionadas com práticas) e as perguntas “já ouviu falar da Brucelose?”, “Brucelose é doença zoonótica/só animal/só humana? e “como a Brucelose se transmite aos humanos?” apresentaram níveis médios de práticas adequadas e conhecimentos correctos inferiores a 20%. Nas explorações infectadas, 39% dos criadores foram positivos (infectados) e nas não infectadas apenas 1.7%. O risco de um criador ser infectado estando numa exploração infectada foi significativamente mais elevado (OR= 36, IC95%: 8.28-157.04). Conclusões: os ambientes dos profissionais (matadouros, salas municipais de abate e talhos e explorações) propiciam o risco à brucelose. O estudo permite aferir que a Brucelose humana em profissionais da pecuária e a Brucelose animal são prevalentes na província do Namibe. Os níveis de seroprevalência detectados são elevados comparandoos com outros encontrados em algumas localidades africanas que possuem condições similares às do Namibe. Perto de duas em cada cinco (40.10%) explorações estão infectadas por esta doença. O número de abortos (média) está claramente relacionado com as explorações infectadas. O conhecimento geral dos profissionais da pecuária sobre a Brucelose é muito insuficiente, tendo os trabalhadores mostrado um maior conhecimento em relação aos criadores, mas ambos com níveis alarmantes. Os criadores infectados estão relacionados com as explorações infectadas. Há necessidade de controlar a doença e de informar e educar os profissionais sobre a brucelose, sendo fundamental que os serviços provinciais de veterinária reforcem acções de divulgação e de fiscalização.

Crystallographic studies of proteins involved in the mRNA localization mechanisms in Drosophila melanogaster and amidation of the peptidoglycan residues in Staphylococcus aureus

Part of the work described in this chapter, was the subject of the following publication: D. Vieira, T. a. Figueiredo, A. Verma, R. G. Sobral, A. M. Ludovice, H. de Lencastre, and J. Trincao, “Purification, crystallization and preliminary X-ray diffraction analysis of GatD, a glutamine amidotransferase-like protein from Staphylococcus aureus peptidoglycan,” Acta Crystallogr. Sect. F Struct. Biol. Commun., vol. 70, no. 5, pp. 1–4, Apr. 2014.

Foresight exercises as a tool for decision-making: the example of two case studies in health

Based on the report for the unit “Foresight Methods Analysis” of the PhD programme on Technology Assessment at the Universidade Nova de Lisboa, under the supervision of Prof. Dr. António B. Moniz

Estigma e percepções dos médicos de Clínica Geral sobre a doença mental e o suicídio

RESUMO: INTRODUÇÃO: A OMS (2001) revela que cerca de 450 milhões de pessoas sofrem de perturbações mentais ou comportamentais em todo o mundo, mas apenas uma pequena minoria tem tratamento, ainda que elementar. Transformam-se em vítimas por causa da sua doença e convertem-se em alvos de estigma e discriminação. O suicídio é considerado como um grande problema de saúde pública em todo o mundo, é uma das principais causas de morte de jovens adultos e situa-se entre as três maiores causas de morte na população entre 15-34 anos (OMS, 2001). As perturbações mentais aumentam o risco de suicídio. A depressão, esquizofrenia, e a utilização de substâncias incrementam o risco de suicídio. Estudos (Sartorius, 2002; Magliano et al., 2012) mostram que os profissionais de saúde, tal como o público em geral, podem ter atitudes negativas e estigma em relação às pessoas com perturbações mentais, podendo agir em conformidade, uma vez feito e conhecido o diagnóstico psiquiátrico. Os clínicos gerais são os receptores das perturbações mentais e tentativas de suicídio nas principais portas de entrada no acesso a cuidados de saúde. As crenças, conhecimentos e contacto com a doença mental e o suicídio, podem influenciar a atenção clínica. OBJECTIVOS: Avaliar o estigma e as percepções dos médicos de clínica geral em relação às tentativas de suicídio, o suicídio e perturbações mentais bem como os possíveis factores associados a estes fenómenos. MATERIAIS E MÉTODOS: Estudo do tipo transversal, combinando métodos quantitativos e qualitativos. A amostra é constituída por 125 sujeitos, médicos de clínica geral. Utilizaram-se as versões adaptadas dos seguintes instrumentos: Questionário sobre Percepções e Estigma em Relação à Saúde Mental e ao Suicídio (Liz Macmin e SOQ, Domino, 2005) e a Escala de Atitudes sobre a Doença Mental (Amanha Hahn, 2002). Para o tratamento estatístico dos dados usou-se a estatística 1) descritiva e 2) Análise estatística das hipóteses formuladas (Qui Quadrado - 2) a correlação entre variáveis (Spearman: ρ, rho). Os dados conectados foram limpos de inconsistências com base no pacote informático e estatístico SPSS versão 20. Para a aferição da consistência interna foi usado o teste de Alfa de Cronbach. RESULTADOS: Uma boa parte da amostra (46.4%) refere que não teve formação formal ou informal em saúde mental e (69.35%) rejeitam a ideia de que “grupos profissionais como médicos, dentistas e psicólogos são mais susceptíveis a cometer o suicídio”. Já (28.0%) têm uma perspectiva pessimista quanto a possibilidade de recuperação total dos sujeitos com perturbação mental. Sessenta e oito(54.4%) associa sujeitos com perturbação mental, a comportamentos estranhos e imprevisíveis, 115 (92.0%) a um baixo QI e 35 (26.7%) a poderem ser violentas e e perigosas. Os dados mostram uma associação estatisticamente significativa (p0.001) entre as variáveis: tempo de serviço no SNS, recear estar perto de sujeitos com doença mental e achar que os sujeitos com doença mental são mais perigosos que outros. Em termos estatísticos, existe uma associação estatitisticamente significativa entre as duas variáveis(X2=9,522; p0.05): percepção de que “é vergonhoso ter uma doença mental” e os conhecimentos em relação à doença mental. Existe uma correlação positiva, fraca e estatisticamente significativa entre os conhecimentos dos clínicos gerais(beneficiar-se de formação em saúde mental) e a percepção sobre os factores de risco (0,187; P0,039). DISCUSSÃO E CONCLUSÕES: A falta de conhecimento sobre as causas e factores de risco para os comportamentos suicidários, opções de intervenção e tratamento, particularmente no âmbito da doença mental, podem limitar a procura de ajuda individual ou dos próximos. Percepções negativas como o facto de não merecerem prioridade nos serviços, mitos (frágeis e cobarde, sempre impulsivo, chamadas de atenção, problemas espirituais) podem constituir-se como um indicador de que os clínicos gerais podem sofrer do mesmo sistema de estigma e crenças, de que sofre o público em geral, podendo agir em conformidade (atitudes de afastamento ereceio). As atitudes são influenciadas por factores como a formação, cultura e sistema de crenças. Sujeitos com boa formação na área da saúde mental têm uma percepção positiva e optimista sobre os factores de risco e uma atitude positiva em relação aos sujeitos com doença mental e comportamentos suicidários.-------------ABSTRACT: INTRODUCTION: The WHO (2001) reveals that about 450 million people suffer from mental or behavioral disorders worldwide, but only a small minority have access to treatment, though elementary. They become victims because of their disease and they become the targets of stigma and discrimination. Suicide is seen as a major public health problem worldwide, is a leading cause of death for young adults and is included among the three major causes of death in the population aged 15-34 years (WHO, 2001). Mental disorders increase the risk of suicide. Depression, schizophrenia, and the substances misuse increase the risk of suicide. Studies (Sartorius, 2002; Magliano et al, 2012) show that health professionals, such as the general public, may have negative attitudes and stigma towards people with mental disorders, and can act accordingly after psychiatric diagnosis is known. General practitioners are the main entry points of mental disorders and suicide attempts in the health sistem. Beliefs, knowledge and contact with mental illness and suicide, may influence clinical care. OBJECTIVES: To assess stigma and perceptions of general practitioners in relation to suicide attempts, suicide and mental disorders as well as possible factors associated with these phenomena. MATERIAL AND METHODS: This was a descriptive cross-sectional study, combining quantitative and qualitative methods. The sample consisted of 125 subjects, general practitioners. We used adapted versions of the following instruments: Questionnaire of Perceptions and Stigma in Relation to Mental Health and Suicide (Liz Macmin and SOQ, Domino, 2005) and the Scale of Attitudes on Mental Illness (Tomorrow Hahn, 2002). For the statistical treatment of the data we used: 1) descriptive (Data distribution by absolute and relative frequencies for each of the variables under study (including mean and standard deviation measures of central tendency and deviation), 2) statistical analysis of hypotheses using (Chi Square - 2, a hypothesis test that is intended to find a value of dispersion for two nominal variables, evaluating the association between qualitative variables) and the correlation between variables (Spearman ρ, rho), a measure of non-parametric correlation, which evaluates an arbitrary monotonic function can be the description of the relationship between two variables, without making any assumptions about the frequency distribution of the variables). For statistical analysis of the correlations were eliminated subjects who did not respond to questions. The collected data were cleaned for inconsistencies based on computer and statistical package SPSS version 20. To measure the internal consistency was used the Cronbach's alpha test. RESULTS: A significant part of the sample 64 (46.4%) reported no formal or informal training in mental health and 86 (69.35%) reject the idea that "professional groups such as doctors, dentists and psychologists are more likely to commit suicide." On the other hand, 42 (28.0%) have a pessimistic view of the possibility of full recovery of individuals with mental disorder. Sixty-eight ( 54.4 % ) of them associates subjects with mental disorder to strange and unpredictable behavior, 115 ( 92.0 % ), to low IQ, 35 ( 26.7 % ) and even to violent and dangerous behavior, 78 ( 62.4 % ) The data show a statistically significant (p = 0.001) relationship between the following variables: length of service in the NHS, fear of being close to individuals with mental illness and considering individuals with mental illness more dangerous than others. In statistical terms, there is a dependency between the two variables (X2 = 9.522, p> 0.05): the perception that "it is shameful to have a mental illness" and knowledge regarding mental illness. There is a positive and statistically significant weak correlation between knowledge of general practitioners (benefit from mental health training) and the perception of the risk factors (0,187; P0,039). DISCUSSION AND CONCLUSIONS: The lack of knowledge about the causes and risk factors for suicidal behavior, intervention and treatment, particularly in the context of mental illness options, may decreaseseeking for help by individual and their relatives. Negative perceptions such as considering that they dont deserve priority in services, myths (weak and cowards, always impulsive, seeking for attentions, spirituals problems) may indicate that general practitioners, may suffer the same stigma and beliefs systems as the general public, and can act accordingly (withdrawal and fear attitudes). Attitudes are influenced by factors such as education, culture and belief system. Subjects with good training in mental health have a positive and optimistic perception of the risk factors and a positiveattitude towards individuals with mental illness and suicidal behaviour.

Experimental and modeling studies on reverse electrodialysis for sustainable power generation

A potentially renewable and sustainable source of energy is the chemical energy associated with solvation of salts. Mixing of two aqueous streams with different saline concentrations is spontaneous and releases energy. The global theoretically obtainable power from salinity gradient energy due to World’s rivers discharge into the oceans has been estimated to be within the range of 1.4-2.6 TW. Reverse electrodialysis (RED) is one of the emerging, membrane-based, technologies for harvesting the salinity gradient energy. A common RED stack is composed by alternately-arranged cation- and anion-exchange membranes, stacked between two electrodes. The compartments between the membranes are alternately fed with concentrated (e.g., sea water) and dilute (e.g., river water) saline solutions. Migration of the respective counter-ions through the membranes leads to ionic current between the electrodes, where an appropriate redox pair converts the chemical salinity gradient energy into electrical energy. Given the importance of the need for new sources of energy for power generation, the present study aims at better understanding and solving current challenges, associated with the RED stack design, fluid dynamics, ionic mass transfer and long-term RED stack performance with natural saline solutions as feedwaters. Chronopotentiometry was used to determinate diffusion boundary layer (DBL) thickness from diffusion relaxation data and the flow entrance effects on mass transfer were found to avail a power generation increase in RED stacks. Increasing the linear flow velocity also leads to a decrease of DBL thickness but on the cost of a higher pressure drop. Pressure drop inside RED stacks was successfully simulated by the developed mathematical model, in which contribution of several pressure drops, that until now have not been considered, was included. The effect of each pressure drop on the RED stack performance was identified and rationalized and guidelines for planning and/or optimization of RED stacks were derived. The design of new profiled membranes, with a chevron corrugation structure, was proposed using computational fluid dynamics (CFD) modeling. The performance of the suggested corrugation geometry was compared with the already existing ones, as well as with the use of conductive and non-conductive spacers. According to the estimations, use of chevron structures grants the highest net power density values, at the best compromise between the mass transfer coefficient and the pressure drop values. Finally, long-term experiments with natural waters were performed, during which fouling was experienced. For the first time, 2D fluorescence spectroscopy was used to monitor RED stack performance, with a dedicated focus on following fouling on ion-exchange membrane surfaces. To extract relevant information from fluorescence spectra, parallel factor analysis (PARAFAC) was performed. Moreover, the information obtained was then used to predict net power density, stack electric resistance and pressure drop by multivariate statistical models based on projection to latent structures (PLS) modeling. The use in such models of 2D fluorescence data, containing hidden, but extractable by PARAFAC, information about fouling on membrane surfaces, considerably improved the models fitting to the experimental data.

Bulletin of Portuguese/Japanese Studies

FCT

Bulletin of Portuguese/Japanese Studies

FCT

Rehabilitation of renders of old buildings in Portugal: survey, supporting methodology proposal and case studies

The main purpose of the research is to present a proposal for a methodology to support the rehabilitation project of renders of old buildings. To achieve the objective it was considered essential to define the main types of participants and aspects to integrate the proposal. The research methodology consists in an inquiry presented to several professional participants in rehabilitation, a market study of materials and products available in Portugal, the design of a methodology proposal and its application to a case study. The inquiry sample totals 24 answers from the targeted professionals. A sequence of relevant supporting procedures consists in the proposal, which aims to provide a supporting methodology to decide and project in this context and also to be tested with its application to the building. This proposal was applied to an old building with load-bearing stone masonry walls and air-lime based renders. It was concluded that the assessment of the building and external renderings’ condition, its diagnosis and of the supporting walls, the definition of intervention, the specification of materials to be used and performance requirements to comply, and also plans for conservation and periodic maintenance, are crucial. From the inquiry, compatibility between materials and complementary roles and points of view of different types of participants in rehabilitation must be highlighted. A proposal for a methodology to support the project could provide useful guidance particularly for architects and construction engineers, and improve the understanding of direct participants on site, therefore contributing for the correct implementation of the intervention.

Modeling and optimization of extracellular polysaccharides production by Enterobacter A47

Polysaccharides are gaining increasing attention as potential environmental friendly and sustainable building blocks in many fields of the (bio)chemical industry. The microbial production of polysaccharides is envisioned as a promising path, since higher biomass growth rates are possible and therefore higher productivities may be achieved compared to vegetable or animal polysaccharides sources. This Ph.D. thesis focuses on the modeling and optimization of a particular microbial polysaccharide, namely the production of extracellular polysaccharides (EPS) by the bacterial strain Enterobacter A47. Enterobacter A47 was found to be a metabolically versatile organism in terms of its adaptability to complex media, notably capable of achieving high growth rates in media containing glycerol byproduct from the biodiesel industry. However, the industrial implementation of this production process is still hampered due to a largely unoptimized process. Kinetic rates from the bioreactor operation are heavily dependent on operational parameters such as temperature, pH, stirring and aeration rate. The increase of culture broth viscosity is a common feature of this culture and has a major impact on the overall performance. This fact complicates the mathematical modeling of the process, limiting the possibility to understand, control and optimize productivity. In order to tackle this difficulty, data-driven mathematical methodologies such as Artificial Neural Networks can be employed to incorporate additional process data to complement the known mathematical description of the fermentation kinetics. In this Ph.D. thesis, we have adopted such an hybrid modeling framework that enabled the incorporation of temperature, pH and viscosity effects on the fermentation kinetics in order to improve the dynamical modeling and optimization of the process. A model-based optimization method was implemented that enabled to design bioreactor optimal control strategies in the sense of EPS productivity maximization. It is also critical to understand EPS synthesis at the level of the bacterial metabolism, since the production of EPS is a tightly regulated process. Methods of pathway analysis provide a means to unravel the fundamental pathways and their controls in bioprocesses. In the present Ph.D. thesis, a novel methodology called Principal Elementary Mode Analysis (PEMA) was developed and implemented that enabled to identify which cellular fluxes are activated under different conditions of temperature and pH. It is shown that differences in these two parameters affect the chemical composition of EPS, hence they are critical for the regulation of the product synthesis. In future studies, the knowledge provided by PEMA could foster the development of metabolically meaningful control strategies that target the EPS sugar content and oder product quality parameters.

Studies on the eucalyptus leaf disease complex in Portugal

Native from south eastern Australia, Eucalyptus globulus is the main species in eucalypts plantations in Portugal. The most serious foliar disease in eucalypt plantations is linked to Mycosphaerella senso lato, which affects young trees in the juvenile phase foliage causing leaf necrosis. This disease results in reduced growth rate of the host and lower wood volume, thus causing significant productivity losses. The most common name for this disease was Mycosphaerella Leaf Disease that became inappropriate when most of the pathogens on eucalypts were re-distributed into several genera. The term "Eucalyptus Leaf Disease Complex" is now more appropriate. The overall aim of this thesis was to investigate the Eucalyptus Leaf Disease Complex in Portugal, focusing on species diversity, taxonomy and the role played by each species in the disease complex on Eucalyptus globulus. Literature on the Eucalyptus Leaf Disease Complex was reviewed and the species were distributed into several genera. A survey based on symptomatic leaves collected from several Eucalyptus globulus plantations and characterized by morphological and molecular tools provided an overview of species incidence and of the most frequent species in the disease complex. The present work reveals additional species of Mycosphaerella senso lato associated with eucalypt plantations in Portugal. Thus, five new records of Teratosphaeria and phylogenetically related species were added to the Iberian Peninsula, namely, Neodevriesia hilliana, for the first time on Myrtaceae; Quasiteratosphaeria mexicana, Teratosphaericola pseudoafricana, Teratosphaeria pluritubularis and Teratosphaeria lusitanica, a new species. Furthermore, new anamorphic structures were found and two new combinations were made. Regarding other genera, some species were observed for the first time, such as Cladosporium cladosporioides, Fusicladium eucalypti, Mycosphaerella madeirae, in the mainland. In addition to leave diseases, Teratosphaeria gauchensis was found causing a severe stem and trunk canker on Eucalyptus globulus. The aggressiveness of several species was compared to evaluate each species individually in the complex, permitting to distinguish different behaviours, from primary to secondary pathogens. Cladosporium cladosporioides, M. communis and M. lateralis, appeared to be more aggressive than Teratosphaeria nubilosa. In fact, contrary to the prevailing views on this disease complex, Teratosphaeria nubilosa is not the only species responsible for the disease, which clearly involves a complex of species acting together.

The reasons behind the progression in PISA scores: An education production function approach using semi-parametric techniques

Research Masters