Strengthening to seismic action of reinforced columns with rectangular cross-section

The first part of this research work regards the assessment of the mathematical modelling of reinforced concrete columns confined with carbon fibre (CFRP) sheets under axial loading. The purpose was to evaluate existing analytical models, contribute to possible improvements and choose the best model(s) to be part of a new model for the prediction of the behaviour of confined columns under bending and compression. For circular columns, a wide group of authors have proposed several models specific for FRP-confined concrete. The analysis of some of the existing models was carried out by comparing these with several tested columns. Although several models predict fairly the peak load only few can properly estimate the load-strain and dilation behaviour of the columns. Square columns confined with CFRP show a more complex interpretation of their behaviour. Accordingly, the analysis of two experimental programs was carried out to propose new modelling equations for the whole behaviour of columns. The modelling results show that the analytical curves are in general agreement with the presented experimental curves for a wide range of dimensions. An analysis similar to the one done for circular columns was this turn carried out for square columns. Few models can fairly estimate the whole behaviour of the columns and with less accuracy at all levels when compared with circular columns. The second part of this study includes seven experimental tests carried out on reinforced concrete rectangular columns with rounded corners, different damage condition and with confinement and longitudinal strengthening systems. It was concluded that the use of CFRP confinement is viable and of effective performance enhancement alone and combined with other techniques, maintaining a good ductile behaviour for established threshold displacements. As regards the use of external longitudinal strengthening combined with CFRP confinement, this system is effective for the performance enhancement and viable in terms of execution. The load capacity was increased significantly, preserving also in this case a good ductile behaviour for threshold displacements. As to the numerical nonlinear modelling of the tested columns, the results show a variation of the peak load of 1% to 10% compared with tests results. The good results are partly due to the inclusion of the concrete constitutive model by Mander et al. modified by Faustino, Chastre & Paula taking into account the confinement effect. Despite the reasonable approximation to tests results, the modelling results showed higher unloading, which leads to an overestimate dissipated energy and residualdisplacement.

Avaliação económica em transplantação renal : abordagem estratégica do processo de doação e análise de custo-utilidade do programa de transplantação renal versus hemodiálise

SUMÁRIO - O desafio atual da Saúde Pública é assegurar a sustentabilidade financeira do sistema de saúde. Em ambiente de recursos escassos, as análises económicas aplicadas à prestação dos cuidados de saúde são um contributo para a tomada de decisão que visa a maximização do bem-estar social sujeita a restrição orçamental. Portugal é um país com 10,6 milhões de habitantes (2011) com uma incidência e prevalência elevadas de doença renal crónica estadio 5 (DRC5), respetivamente, 234 doentes por milhão de habitantes (pmh) e 1.600 doentes/pmh. O crescimento de doenças associadas às causas de DRC, nomeadamente, diabetes Mellitus e hipertensão arterial, antecipam uma tendência para o aumento do número de doentes. Em 2011, dos 17.553 doentes em tratamento substitutivo renal, 59% encontrava-se em programa de hemodiálise (Hd) em centros de diálise extra-hospitalares, 37% viviam com um enxerto renal funcionante e 4% estavam em diálise peritoneal (SPN, 2011). A lista ativa para transplante (Tx) renal registava 2.500 doentes (SPN 2009). O Tx renal é a melhor modalidade terapêutica pela melhoria da sobrevida, qualidade de vida e relação custo-efetividade, mas a elegibilidade para Tx e a oferta de órgãos condicionam esta opção. Esta investigação desenvolveu-se em duas vertentes: i) determinar o rácio custo-utilidade incremental do Tx renal comparado com a Hd; ii) avaliar a capacidade máxima de dadores de cadáver em Portugal, as características e as causas de morte dos dadores potenciais a nível nacional, por hospital e por Gabinete Coordenador de Colheita e Transplantação (GCCT), e analisar o desempenho da rede de colheita de órgãos para Tx. Realizou-se um estudo observacional/não interventivo, prospetivo e analítico que incidiu sobre uma coorte de doentes em Hd que foi submetida a Tx renal. O tempo de seguimento mínimo foi de um ano e máximo de três anos. No início do estudo, colheram-se dados sociodemográficos e clínicos em 386 doentes em Hd, elegíveis para Tx renal. A qualidade de vida relacionada com a saúde (QVRS) foi avaliada nos doentes em Hd (tempo 0) e nos transplantados, aos três, seis, 12 meses, e depois, anualmente. Incluíram-se os doentes que por falência do enxerto renal transitaram para Hd. Na sua medição, utilizou-se um instrumento baseado em preferências da população, o EuroQol-5D, que permite o posterior cálculo dos QALY. Num grupo de 82 doentes, a QVRS em Hd foi avaliada em dois tempos de resposta o que permitiu a análise da sua evolução. Realizou-se uma análise custo-utilidade do Tx renal comparado com a Hd na perspetiva da sociedade. Identificaram-se os custos diretos, médicos e não médicos, e as alterações de produtividade em Hd e Tx renal. Incluíram-se os custos da colheita de órgãos, seleção dos candidatos a Tx renal e follow-up dos dadores vivos. Cada doente transplantado foi utilizado como controle de si próprio em diálise. Avaliou-se o custo médio anual em programa de Hd crónica relativo ao ano anterior à Tx renal. Os custos do Tx foram avaliados prospetivamente. Considerou-se como horizonte temporal o ciclo de vida nas duas modalidades. Usaram-se taxas de atualização de 0%, 3% e 5% na atualização dos custos e QALY e efetuaram-se análises de sensibilidade one way. Entre 2008 e 2010, 65 doentes foram submetidos a Tx renal. Registaram-se, prospetivamente, os resultados em saúde incluíndo os internamentos e os efeitos adversos da imunossupressão, e o consumo dos recursos em saúde. Utilizaram-se modelos de medidas repetidas na avaliação da evolução da QVRS e modelos de regressão múltipla na análise da associação da QVRS e dos custos do transplante com as características basais dos doentes e os eventos clínicos. Comparativamente à Hd, observou-se melhoria da utilidade ao 3º mês de Tx e a qualidade de vida aferida pela escala EQ-VAS melhorou em todos os tempos de observação após o Tx renal. O custo médio da Hd foi de 32.567,57€, considerado uniforme ao longo do tempo. O custo médio do Tx renal foi de 60.210,09€ no 1º ano e 12.956,77€ nos anos seguintes. O rácio custo-utilidade do Tx renal vs Hd crónica foi de 2.004,75€/QALY. A partir de uma sobrevivência do enxerto de dois anos e cinco meses, o Tx associou-se a poupança dos custos. Utilizaram-se os dados nacionais dos Grupos de Diagnóstico Homogéneos e realizou-se um estudo retrospectivo que abrangeu as mortes ocorridas em 34 hospitais com colheita de órgãos, em 2006. Considerou-se como dador potencial o indivíduo com idade entre 1-70 anos cuja morte ocorrera a nível hospitalar, e que apresentasse critérios de adequação à doação de rim. Analisou-se a associação dos dadores potenciais com características populacionais e hospitalares. O desempenho das organizações de colheita de órgãos foi avaliado pela taxa de conversão (rácio entre os dadores potenciais e efetivos) e pelo número de dadores potenciais por milhão de habitantes a nível nacional, regional e por Gabinete Coordenador de Colheita e Transplantação (GCCT). Identificaram-se 3.838 dadores potenciais dos quais 608 apresentaram códigos da Classificação Internacional de Doenças, 9.ª Revisão, Modificações Clínicas (CID- 9-MC) que, com maior frequência, evoluem para a morte cerebral. O modelo logit para dados agrupados identificou a idade, o rácio da lotação em Unidades de Cuidados Intensivos e lotação de agudos, existência de GCCT e de Unidade de Transplantação, e mortalidade por acidente de trabalho como fatores preditivos da conversão dum dador potencial em efetivo e através das estimativas do modelo logit quantificou-se a probabilidade dessa conversão. A doação de órgãos deve ser assumida como uma prioridade e as autoridades em saúde devem assegurar o financiamento dos hospitais com programas de doação, evitando o desperdício de órgãos para transplantação, enquanto um bem público e escasso. A colheita de órgãos deve ser considerada uma opção estratégica da atividade hospitalar orientada para a organização e planeamento de serviços que maximizem a conversão de dadores potenciais em efetivos incluindo esse critério como medida de qualidade e efetividade do desempenho hospitalar. Os resultados deste estudo demonstram que: 1) o Tx renal proporciona ganhos em saúde, aumento da sobrevida e qualidade de vida, e poupança de custos; 2) em Portugal, a taxa máxima de eficácia da conversão dos dadores cadavéricos em dadores potenciais está longe de ser atingida. O investimento na rede de colheita de órgãos para Tx é essencial para assegurar a sustentabilidade financeira e promover a qualidade, eficiência e equidade dos cuidados em saúde prestados na DRC5.

Light harvesting in solar cells using natural pigments from red fruits adsorbed to mesoporous TiO2

Nature has developed strategies to present us with a wide variety of colours, from the green of leaves to the bright colours seen in flowers. Anthocyanins are between these natural pigments that are responsible for the great diversity of colours seen in flowers and fruits. Anthocyanins have been used to sensitize titanium dioxide (TiO2) in Dye-Sensitized Solar Cells (DSSCs). DSSCs have become one of the most popular research topic in photovoltaic cells due to their low production costs when compared to other alternatives. DSSCs are inspired in what happens in nature during photosynthesis. A primary charge separation is achieved by means of a photoexcited dye capable of performing the electron injection into the conduction band of a wide band-gap semiconductor, usually TiO2. With this work we aimed to synthesize a novel mesoporous TiO2 structure as the semiconductor in order to increase the dye loading. We used natural occurring dyes such as anthocyanins and their synthetic flavylium relatives, as an alternative to the widely used metal complexes of Ru(II) which are expensive and are environmentally unsafe. This offers not only the chance to use safer dyes for DSSCs, but also to take profit of waste biological products, such as wine and olive oil production residues that are heavily loaded with anthocyanin dyes. We also performed a photodegradation study using TiO2 as the catalyst to degrade dye contaminants, such as those from the wine production waste, by photo-irradiation of the system in the visible region of the light spectrum. We were able to succeed in the synthesis of mesoporous TiO2 both powder and thin film, with a high capacity to load a large amount of dye. We proved the concept of photodegradation using TiO2 as catalyst. And finally, we show that wine production waste is a possible dye source to DSSCs application.

Optimisation and design of post-tensioning anchorage corner blisters in concrete box girder bidges

The design of anchorage blisters of internal continuity post-tensioning tendons of bridges built by the cantilever method, presents some peculiarities, not only because they are intermediate anchorages but also because these anchorages are located in blisters, so the prestressing force has to be transferred from the blister the bottom slab and web of the girder. The high density of steel reinforcement in anchorage blisters is the most common reason for problems with concrete cast in situ, resulting in zones with low concrete compacity, leading to concrete crushing failures under the anchor plates. A solution may involve improving the concrete compression and tensile strength. To meet these requirements a high-performance fibre reinforced self-compacting mix- ture (HPFRC) was used in anchorage corner blisters of post-tensioning tendons, reducing the concrete cross-section and decreasing the reinforcement needed. To assess the ultimate capacity and the adequate serviceability of the local anchorage zone after reducing the minimum concrete cross-section and the confining reinforcement, specified by the anchorage device supplier for the particular tendon, load transfer tests were performed. To investigate the behaviour of anchorage blisters regarding the transmission of stresses to the web and the bottom slab of the girder, and the feasibility of using high performance concrete only in the blister, two half scale models of the inferior corner of a box girder existing bridge were studied: a reference specimen of ordinary reinforced concrete and a HPFRC blister specimen. The design of the reinforcement was based in the tensile forces obtained on strut-and-tie models. An experimental program was carried out to assess the models used in design and to study the feasibility of using high performance concrete only in the blister, either with casting in situ, or with precast solutions. A non-linear finite element analysis of the tested specimens was also performed and the results compared.

Impact of carbon/nitrogen feeding strategy on polyhydroxyalkanoates production using mixed microbial cultures

Polyhydroxyalkanoates (PHA) production using mixed microbial cultures (MMC) requires a multi-stage process involving the microbial selection of PHA-storing microorganisms, typically operated in sequencing batch reactors (SBR), and an accumulation reactor. Since low-cost renewable feedstocks used as process feedstock are often nitrogen-deficient, nutrient supply in the selection stage is required to allow for microbial growth. In this context, the possibility to uncouple nitrogen supply from carbon feeding within the SBR cycle has been investigated in this study. Moreover, three different COD:N ratios (100:3.79, 100:3.03 and 100:2.43) were tested in three different runs which also allowed the study of COD:N ratio on the SBR performance. For each run, a synthetic mixture of acetic and propionic acids at an overall organic load rate of 8.5 gCOD L-1 d-1 was used as carbon feedstock, whereas ammonium sulfate was the nitrogen source in a lab-scale sequence batch reactor (SBR) with 1 L of working volume. Besides, a sludge retention time (SRT) of 1 d was used as well as a 6 h cycle length. The uncoupled feeding strategy significantly enhanced the selective pressure towards PHA-storing microorganisms, resulting in a two-fold increase in the PHA production (up to about 1.3 gCOD L-1). A high storage response was observed for the two runs with the COD:N ratios (gCOD:gN) of 100:3.79 and 100:3.03, whereas the lowest investigated nitrogen load resulted in very poor performance in terms of polymer production. In fact, strong nitrogen limitation caused fungi to grow and a very poor storage ability by microorganisms that thrived in those conditions. The COD:N ratio also affected the polymer composition, indeed the produced poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) showed a variable HV content (1-20 %, w/w) among the three runs, lessening as the COD:N increased. This clearly suggests the possibility to use the COD:N ratio as a tool for tuning polymer properties regardless the composition of the feedstock.

Share and Strife - The Strait of Melaka and the Portuguese (16th and 17th centuries)

The Strait of Melaka is the longest strait in the world, stretching for about 800 km from the northern tip of Sumatra to Singapore. It exhibits a dual character like no other, being simultaneously a privileged linking passage of two seas and two knots of human civilization – India and China – and a »bottleneck« that constrains the maritime connections between them. Today, the latter aspect is globally dominant. The strait is considered and analysed mostly as an obstacle rather than a linking point: how to reach China from the West or elsewhere is no longer an issue, but securing the vital flows that pass into the strait on a daily basis undoubtedly is. Accidents, natural catastrophes, political local crises or terrorist attacks are permanent dangers that could cut this umbilical cord of world trade and jeopardize a particularly sensitive and vulnerable area; piracy and pollution are the most common local threats and vulnerabilities.

Rehabilitation of renders of old buildings in Portugal: survey, supporting methodology proposal and case studies

The main purpose of the research is to present a proposal for a methodology to support the rehabilitation project of renders of old buildings. To achieve the objective it was considered essential to define the main types of participants and aspects to integrate the proposal. The research methodology consists in an inquiry presented to several professional participants in rehabilitation, a market study of materials and products available in Portugal, the design of a methodology proposal and its application to a case study. The inquiry sample totals 24 answers from the targeted professionals. A sequence of relevant supporting procedures consists in the proposal, which aims to provide a supporting methodology to decide and project in this context and also to be tested with its application to the building. This proposal was applied to an old building with load-bearing stone masonry walls and air-lime based renders. It was concluded that the assessment of the building and external renderings’ condition, its diagnosis and of the supporting walls, the definition of intervention, the specification of materials to be used and performance requirements to comply, and also plans for conservation and periodic maintenance, are crucial. From the inquiry, compatibility between materials and complementary roles and points of view of different types of participants in rehabilitation must be highlighted. A proposal for a methodology to support the project could provide useful guidance particularly for architects and construction engineers, and improve the understanding of direct participants on site, therefore contributing for the correct implementation of the intervention.

Implementation of membrane processes for improvement of the detection of food contaminants

The EM3E Master is an Education Programme supported by the European Commission, the European Membrane Society (EMS), the European Membrane House (EMH), and a large international network of industrial companies, research centres and universities (http://www.em3e.eu)

Switching mode power amplifier for bluetooth applications

Modern fully integrated transceivers architectures, require circuits with low area, low cost, low power, and high efficiency. A key block in modern transceivers is the power amplifier, which is deeply studied in this thesis. First, we study the implementation of a classical Class-A amplifier, describing the basic operation of an RF power amplifier, and analysing the influence of the real models of the reactive components in its operation. Secondly, the Class-E amplifier is deeply studied. The different types of implementations are reviewed and theoretical equations are derived and compared with simulations. There were selected four modes of operation for the Class-E amplifier, in order to perform the implementation of the output stage, and the subsequent comparison of results. This led to the selection of the mode with the best trade-off between efficiency and harmonics distortion, lower power consumption and higher output power. The optimal choice was a parallel circuit containing an inductor with a finite value. To complete the implementation of the PA in switching mode, a driver was implemented. The final block (output stage together with the driver) got 20 % total efficiency (PAE) transmitting 8 dBm output power to a 50 W load with a total harmonic distortion (THD) of 3 % and a total consumption of 28 mW. All implementations are designed using standard 130 nm CMOS technology. The operating frequency is 2.4 GHz and it was considered an 1.2 V DC power supply. The proposed circuit is intended to be used in a Bluetooth transmitter, however, it has a wider range of applications.

Wideband CMOS low noise amplifiers

Modern fully integrated receiver architectures, require inductorless circuits to achieve their potential low area, low cost, and low power. The low noise amplifier (LNA), which is a key block in such receivers, is investigated in this thesis. LNAs can be either narrowband or wideband. Narrowband LNAs use inductors and have very low noise figure, but they occupy a large area and require a technology with RF options to obtain inductors with high Q. Recently, wideband LNAs with noise and distortion cancelling, with passive loads have been proposed, which can have low NF, but have high power consumption. In this thesis the main goal is to obtain a very low area, low power, and low-cost wideband LNA. First, it is investigated a balun LNA with noise and distortion cancelling with active loads to boost the gain and reduce the noise figure (NF). The circuit is based on a conventional balun LNA with noise and distortion cancellation, using the combination of a common-gate (CG) stage and common-source (CS) stage. Simulation and measurements results, with a 130 nm CMOS technology, show that the gain is enhanced by about 3 dB and the NF is reduced by at least 0.5 dB, with a negligible impact on the circuit linearity (IIP3 is about 0 dBm). The total power dissipation is only 4.8 mW, and the active area is less than 50 x 50 m2 . It is also investigated a balun LNA in which the gain is boosted by using a double feedback structure.We propose to replace the load resistors by active loads, which can be used to implement local feedback loops (in the CG and CS stages). This will boost the gain and reduce the noise figure (NF). Simulation results, with the same 130 nm CMOS technology as above, show that the gain is 24 dB and NF is less than 2.7 dB. The total power dissipation is only 5.4 mW (since no extra blocks are required), leading to a figure-of-merit (FoM) of 3.8 mW

Damage propagation in composite Materials meso-mechanical models

Composite materials have a complex behavior, which is difficult to predict under different types of loads. In the course of this dissertation a methodology was developed to predict failure and damage propagation of composite material specimens. This methodology uses finite element numerical models created with Ansys and Matlab softwares. The methodology is able to perform an incremental-iterative analysis, which increases, gradually, the load applied to the specimen. Several structural failure phenomena are considered, such as fiber and/or matrix failure, delamination or shear plasticity. Failure criteria based on element stresses were implemented and a procedure to reduce the stiffness of the failed elements was prepared. The material used in this dissertation consist of a spread tow carbon fabric with a 0°/90° arrangement and the main numerical model analyzed is a 26-plies specimen under compression loads. Numerical results were compared with the results of specimens tested experimentally, whose mechanical properties are unknown, knowing only the geometry of the specimen. The material properties of the numerical model were adjusted in the course of this dissertation, in order to find the lowest difference between the numerical and experimental results with an error lower than 5% (it was performed the numerical model identification based on the experimental results).

The determinants of net interest margins & net interest spreads in the Russian & Japanese Commercial Banking sectors

This study presents an empirical investigation of the determinants of net interest margins and spreads in the Russian and Japanese banking sectors with a particular focus on commercial banks. Net interest mar-gins and spreads serve as indicators of financial intermediation efficiency. This paper employed a bank-level unbalanced panel dataset prolonging from 2005 to 2014. My main empirical results show that bank characteristics explain the most of the variation in not only net interest margins but also in spreads. Capi-talization, liquidity risk, inflation, economic growth, private and government debt are important determi-nants of margin in Russia. In Japan to the contrary loan and deposit market concentration along with bank size do predominate. Common significant variables in both countries are the substitution effect, cost effi-ciency and profitability. Turning to net interest spreads, micro- and macro-specific variables are the main significant drivers in Russia. I reach the conclusion that there are no significant determinants of net interest spreads in Japan within the original selection of variables, but operating efficiency and deposits to total funding seem to prevail. In both countries, there are solid differences in the net interest margins as well as spreads once the pre- and the post-crisis periods are considered.

Coupling organic substrate removal to methane production in a fully biological microbial electrolysis cell

Microbial electrolysis cells (MECs) are an innovative and emerging technique based on the use of solid-state electrodes to stimulate microbial metabolism for wastewater treatment and simultaneous production of value-added compounds (such as methane). This research studied the performance of a two-chamber MEC in terms of organic matter oxidation (at the anode) and methane production (at the cathode). MEC‟s anode had been previously inoculated with an activated sludge, whereas the cathode chamber inoculum was an anaerobic sludge (containing methanogenic microorganisms). During the experimentation, the bioanode was continuously fed with synthetic solutions in anaerobic basal medium, at an organic load rate (OLR) of around 1 g L-1 d-1, referred to the chemical oxygen demand (COD). At the beginning (Run I), the feeding solution contained acetate and subsequently (Run II) it was replaced with a more complex solution containing soluble organic compounds other than acetate. For both conditions, the anode potential was controlled at -0.1 V vs. standard hydrogen electrode, by means of a potentiostat. During Run I, over 80% of the influent acetate was anaerobically oxidized at the anode, and the resulting electric current was recovered as methane at the cathode (with a cathode capture efficiency, CCE, accounting around 115 %). The average energy efficiency of the system (i.e., the energy captured into methane relative to the electrical energy input) under these conditions was over 170%. However, reactor‟s performance decreased over time during this run. Throughout Run II, a substrate oxidation over 60% (on COD basis) was observed. The electric current produced (57% of coulombic efficiency) was also recovered as methane, with a CCE of 90%. For this run the MEC‟s average energy efficiency accounted for almost 170 %. During all the experimentation, a very low biomass growth was observed at the anode whereas ammonium was transferred through the cationic membrane and concentrated at the cathode. Tracer experiments and scanning electron microscopy analyses were also carried out to gain a deeper insight into the reactor performance and also to investigate the possible reasons for partial loss of performance. In conclusion, this research suggests the great potential of MEC to successfully treat low-strength wastewaters, with high energy efficiency and very low sludge production.