A piezoelectric based energy harvester interface for a CMOS wireless sensor IC

In this thesis a piezoelectric energy harvesting system, responsible for regulating the power output of a piezoelectric transducer subjected to ambient vibration, is designed to power an RF receiver with a 6 mW power consump-tion. The electrical characterisation of the chosen piezoelectric transducer is the starting point of the design, which subsequently presents a full-bridge cross-coupled rectifier that rectifies the AC output of the transducer and a low-dropout regulator responsible for delivering a constant voltage system output of 0.6 V, with low voltage ripple, which represents the receiver’s required sup-ply voltage. The circuit is designed using CMOS 130 nm UMC technology, and the system presents an inductorless architecture, with reduced area and cost. The electrical simulations run for the complete circuit lead to the conclusion that the proposed piezoelectric energy harvesting system is a plausible solution to power the RF receiver, provided that the chosen transducer is subjected to moderate levels of vibration.

Who owns the largest firms around the world?

In this research paper we evaluate how corporate control around the world is defined and which variables, related to a firm's characteristics and the countries' infrastructures, influences this. We find that there is a small number of countries where firms are widely held. The role of financial institutions seems to be different in civil and common law-based countries. While they seem to act as a monitor of management in common law-based countries, in civil law countries they act as a monitor of large shareholders. Finally, we find that firm's size is the most important determinant of ultimate owners.

Prospective system analysis of stationary battery systems under the frame of Constructive Technology Assessment

Based on the report for the unit “Project IV” of the PhD programme on Technology Assessment under the supervision of Dr.-Ing. Marcel Weil and Prof. Dr. António Brandão Moniz. The report was presented and discussed at the Doctorate Conference on Technologogy Assessment in July 2013 at the University Nova Lisboa, Caparica campus.

Towards an integrated technology management across the rail supply chain extended to society: building the case study on high-speed trains

The present paper was prepared for the course “Project III”, with the supervision of Prof. António Moniz, reporting on the author speaking notes at the Winter School on Technology Assessment, 6-7 December 2010, as part of the Doctoral Programme on Technology Assessment at FCT-UNL.

Post-merger innovative performance in the renewable energy sector

Due to global warming and shrinking fossil fuel resources, politics as well as society urge for a reduction of green house gas (GHG) emissions. This leads to a re-orientation towards a renewable energy sector. In this context, innovation and new technologies are key success factors. Moreover, the renewable energy sector has entered a consolidation stage, where corporate investors and mergers and acquisitions (M&A) gain in importance. Although both M&A and innovation in the renewable energy sector are important corporate strategies, the link between those two aspects has not been examined before. The present thesis examines the research question how M&A influence the acquirer’s post-merger innovative performance in the renewable energy sector. Based on a framework of relevant literature, three hypotheses are defined. First, the relation between non-technology oriented M&A and post-merger innovative performance is discussed. Second, the impact of absolute acquired knowledge on postmerger innovativeness is examined. Third, the target-acquirer relatedness is discussed. A panel data set of 117 firms collected over a period of six years has been analyzed via a random effects negative binomial regression model and a time lag of one year. The results support a non-significant, negative impact of non-technology M&A on postmerger innovative performance. The applied model did not support a positive and significant impact of absolute acquired knowledge on post-merger innovative performance. Lastly, the results suggest a reverse relation than postulated by Hypothesis 3. Targets from the same industry significantly and negatively influence the acquirers’ innovativeness.

To what extent do aspects of sustainability impact established firms' resilience

An organizations´ level of sustainability has so far been primarily been analyzed within the context of economic performance. This study changes that dependent variable to “resilience”, namely a company’s ability to recover from potential lethal shocks or disruptive events. The research questions aims to investigate whether sustainability and resilience are related. This study utilizes the financial crisis from 2007/08 as disruptive event, as it encompassed market phase-out but also survival by established firms. Two Swiss luxury watchmaking companies have been chosen as industry sample and the study’s investigation is based on a comparative case study approach. The latter applies both quantitative data, in the form of the respective annual company reports, and qualitative data, in the form of semi-structured interviews with three stakeholder groups. Findings indicate that the investigated measures of sustainability are related the investigated companies’ level of resilience. These findings contribute to the building of new theory towards resilience as this study outlines specifically which measures have been proven to be of relevance for companies’ resilience. Moreover, the results are of high relevance for companies that are operating in constant evolving markets and struggling adapting to any disruptive environment as it is outlined why and how comparative companies have to be sustainable in order to become more resilient towards future shocks.

Valorization of olive pomace through combination of biocatalysis with supercritical fluid technology

A supercritical carbon dioxide (scCO2) based oil extraction method was implemented on olive pomace (alperujo), and an oil yield of 25,5 +/- 0,8% (goil/gdry residue) was obtained. By Soxhlet extraction with hexane, an oil extraction yield of 28,9 +/- 0,8 % was obtained, which corresponds to an efficiency of 88,4 +/- 4,8 % for the supercritical method. The scCO2 extraction process was optimized for operating conditions of 50 MPa and 348,15 K, for which an oil loading of 32,60 g oil/kg CO2 was calculated. As a proof of concept, olive pomace was used as feedstock for biodiesel production, in a process combining the use of lipase as a catalyst with the use of scCO2 as a solvent, and integrating the steps of oil extraction, oil to biodiesel transesterification and subsequent separation of the latter. In the conducted experiments, FAME (fatty acid methyl ester) purities of 90% were obtained, with the following operating parameters: an oil:methanol molar ratio of 1:24; a residence time of 7,33 and 11,6 mins; a pressure of 40 MPa; a temperature of 313,15 K; and Lipozyme (Mucor miehei; Sigma-Aldritch) as an enzyme. However, oscillations of FAME purity were registered throughout the experiments, which could possibly be due to methanol accumulation in the enzymatic reactor. Finally, the phenolic content of olive pomace, and the effect of the drying process – oven or freeze-drying – and the extraction methods – hydro-alcoholic method and supercritical method – on the phenolic content were analysed. It was verified that the oven-drying process on the olive pomace preserved 90,1 +/- 3,6 % of the total phenolic content. About 62,3 +/- 5,53% of the oven-dried pomace phenolic content was extracted using scCO2 at 60 MPa and 323,15 K. Seven individual phenols – hydroxytyrosol, tyrosol, oleuropein, quercetin, caffeic acid, ferulic acid and p-coumaric acid – were identified and quantified by HPLC.

Quadrature generators based on ring oscillators and shift registers

Quadrature oscillators are key elements in modern radio frequency (RF) transceivers and very useful nowadays in wireless communications, since they can provide: low quadrature error, low phase-noise, and wide tuning range (useful to cover several bands). RC oscillators can be fully integrated without the need of external components (external high Q-inductors), optimizing area, cost, and power consumption. The conventional structure of ring oscillator offers poor frequency stability and phasenoise, low quality factor (Q), and besides being vulnerable to process, voltage and temperature (PVT) variations, its performance degrades as the frequency of operation increases. This thesis is devoted to quadrature oscillators and presents a detailed comparative study of ring oscillator and shift register (SR) approaches. It is shown that in SRs both phase-noise and phase error are reduced, while ring oscillators have the advantage of occupying less area and less consumption due to the reduced number of components in the circuit. Thus, although ring oscillators are more suitable for biomedical applications, SRs are more appropriate for wireless applications, especially when specification requirements are more stringent and demanding. The first architecture studied consists in a simple CMOS ring oscillator employing an odd number of static single-ended inverters as delay cells. Subsequently, the quadrature 4-stage ring oscillator concept is shown and post-layout simulations are presented. The 3 and 4-phase single-frequency local oscillator (LO) generators employing SRs are presented, the latter with 50% and 25% duty-cycles. The circuits operate at 600 MHz and 900 MHz, and were designed in a 130 nm standard CMOS technology with a voltage supply of 1.2 V.

Characterization of earth-based mortars for rammed earth repair

All over the world, many earth buildings are deteriorating due to lack of maintenance and repair. Repairs on rammed earth walls are mainly done with mortars, by rendering application; however, often the repair is inadequate, resorting to the use of incompatible materials, including cement-based mortars. It has been observed that such interventions, in walls that until that day only had presented natural ageing issues, created new problems, much more dangerous for the building than the previous ones, causing serious deficiencies in this type of construction. One of the problems is that the detachment of the new cement-based mortar rendering only occurs after some time but, until that occurrence, degradations develop in the wall itself. When the render detaches, instead of needing only a new render, the surface has to be repaired in depth, with a repair mortar. Consequently, it has been stablished that the renders, and particularly repair mortars, should have physical, mechanical and chemical properties similar to those of the rammed earth walls. This article intends to contribute to a better knowledge of earth-based mortars used to repair the surface of rammed earth walls. The studied mortars are based on four types of earth: three of them were collected from non-deteriorated parts of walls of unstabilized rammed earth buildings located in Alentejo region, south of Portugal; the fourth is a commercial earth, consisting mainly of clay. Other components were also used, particularly: sand to control shrinkage; binders stabilizers such as dry hydrated air-lime, natural hydraulic lime, Portland cement and natural cement; as well as natural vegetal fibers (hemp fibers). The experimental analysis of the mortars in the fresh state consisted in determining the consistency by flow table and the bulk density. In the hardened state, the tests made it possible to evaluate the following properties: linear and volumetric shrinkage; capillary water absorption; drying capacity; dynamic modulus of elasticity; flexural and compressive strength.

Historic and potential technology transition paths of grid battery storage: Co-evolution of energy grid, electric mobility and batteries

Scarcity of fuels, changes in environmental policy and in society increased the interest in generating electric energy from renewable energy sources (RES) for a sustainable energy supply in the future. The main problem of RES as solar and wind energy, which represent a main pillar of this transition, is that they cannot supply constant power output. This results inter alia in an increased demand of backup technologies as batteries to assure electricity system safety. The diffusion of energy storage technologies is highly dependent on the energy system and transport transition pathways which might lead to a replacement or reconfiguration of embedded socio-technical practices and regimes (by creating new standards or dominant designs, changing regulations, infrastructure and user patterns). The success of this technology is dependent on hardly predictable future technical advances, actor preferences, development of competing technologies and designs, diverging interests of actors, future cost efficiencies, environmental performance, the evolution of market demand and design and evolution of our society.

Chitosan-based magnetic nanoparticles for osteosarcoma theranostic

Cancer is a well-known disease with a significant impact in society not only due to its incidence, more evident in more developed countries, but also due to the expenses related to medical treat-ments. Cancer research is considered an increasingly logical science with great potential for the development of new treatment options. Advances in nanomedicine have resulted in rapid devel-opment of nanomaterials with considerable potential in cancer diagnostics and treatment. The combination of diagnosis and treatment in a single nano-platform is named theranostic. In this PhD thesis a theranostic system for osteosarcoma was proposed, composed by a magnetic core, a polymeric coating, and a chemotherapeutic drug. The presence of a specific targeting agent, in this case a monoclonal antibody, provides high specificity to the proposed theranostic system. For the core of the proposed theranostic system, stable aqueous suspensions of superparamagnetic iron oxide nanoparticles with an average diameter of 9 nm were produced. Chitosan-based poly-meric nanoparticles with a hydrodynamic diameter around 150 nm were successfully produced. Incorporation of iron oxide nanoparticles into the polymeric ones increased their hydrodynamic diameter to at least 250 nm. A monoclonal antibody specific for a transmembranar protein (car-bonic anhydrase IX) present in solid tumors was developed by hybridoma technology. Functional hybridomas producing the desired monoclonal antibodies were obtained. The proposed theranostic system functionality was evaluated in separated parts of its components. Uncoated and coated iron oxide nanoparticles with chitosan-based polymers generated heat under the application of an external alternating magnetic field. Uncoated iron oxide nanoparticles sta-bilized with oleic acid were able to enhance contrast in magnetic resonance imaging. Drug deliv-ery studies were conducted in chitosan-based polymeric nanoparticles without and with the in-corporation of iron oxide nanoparticles, demonstrating to be an effective drug delivery platform for doxorubicin. The theranostic system proposed in this PhD thesis is very promising for cancer theranostic, demonstrating to be applicable in solid tumors such as osteosarcoma.

Decisions of technology innovation: the role of indicators

This work presents research conducted to understand the role of indicators in decisions of technology innovation. A gap was detected in the literature of innovation and technology assessment about the use and influence of indicators in this type of decision. It was important to address this gap because indicators are often frequent elements of innovation and technology assessment studies. The research was designed to determine the extent of the use and influence of indicators in decisions of technology innovation, to characterize the role of indicators in these decisions, and to understand how indicators are used in these decisions. The latter involved the test of four possible explanatory factors: the type and phase of decision, and the context and process of construction of evidence. Furthermore, it focused on three Portuguese innovation groups: public researchers, business R&D&I leaders and policymakers. The research used a combination of methods to collect quantitative and qualitative information, such as surveys, case studies and social network analysis. This research concluded that the use of indicators is different from their influence in decisions of technology innovation. In fact, there is a high use of indicators in these decisions, but lower and differentiated differences in their influence in each innovation group. This suggests that political-behavioural methods are also involved in the decisions to different degrees. The main social influences in the decisions came mostly from hierarchies, knowledge-based contacts and users. Furthermore, the research established that indicators played mostly symbolic roles in decisions of policymakers and business R&D&I leaders, although their role with researchers was more differentiated. Indicators were also described as helpful instruments to conduct a reasonable interpretation of data and to balance options in innovation and technology assessments studies, in particular when contextualised, described in detail and with discussion upon the options made. Results suggest that there are four main explanatory factors for the role of indicators in these decisions: First, the type of decision appears to be a factor to consider when explaining the role of indicators. In fact, each type of decision had different influences on the way indicators are used, and each type of decision used different types of indicators. Results for policy-making were particularly different from decisions of acquisition and development of products/technology. Second, the phase of the decision can help to understand the role indicators play in these decisions. Results distinguished between two phases detected in all decisions – before and after the decision – as well as two other phases that can be used to complement the decision process and where indicators can be involved. Third, the context of decision is an important factor to consider when explaining the way indicators are taken into consideration in policy decisions. In fact, the role of indicators can be influenced by the particular context of the decision maker, in which all types of evidence can be selected or downplayed. More importantly, the use of persuasive analytical evidence appears to be related with the dispute existent in the policy context. Fourth and last, the process of construction of evidence is a factor to consider when explaining the way indicators are involved in these decisions. In fact, indicators and other evidence were brought to the decision processes according to their availability and capacity to support the different arguments and interests of the actors and stakeholders. In one case, an indicator lost much persuasion strength with the controversies that it went through during the decision process. Therefore, it can be argued that the use of indicators is high but not very influential; their role is mostly symbolic to policymakers and business decisions, but varies among researchers. The role of indicators in these decisions depends on the type and phase of the decision and the context and process of construction of evidence. The latter two are related to the particular context of each decision maker, the existence of elements of dispute and controversies that influence the way indicators are introduced in the decision-making process.

Genetic algorithm for shipping route estimation with long-range tracking data : automatic reconstruction of shipping routes based on the historical ship positions for maritime safety applications

Ship tracking systems allow Maritime Organizations that are concerned with the Safety at Sea to obtain information on the current location and route of merchant vessels. Thanks to Space technology in recent years the geographical coverage of the ship tracking platforms has increased significantly, from radar based near-shore traffic monitoring towards a worldwide picture of the maritime traffic situation. The long-range tracking systems currently in operations allow the storage of ship position data over many years: a valuable source of knowledge about the shipping routes between different ocean regions. The outcome of this Master project is a software prototype for the estimation of the most operated shipping route between any two geographical locations. The analysis is based on the historical ship positions acquired with long-range tracking systems. The proposed approach makes use of a Genetic Algorithm applied on a training set of relevant ship positions extracted from the long-term storage tracking database of the European Maritime Safety Agency (EMSA). The analysis of some representative shipping routes is presented and the quality of the results and their operational applications are assessed by a Maritime Safety expert.