Characterization of earth-based mortars for rammed earth repair

All over the world, many earth buildings are deteriorating due to lack of maintenance and repair. Repairs on rammed earth walls are mainly done with mortars, by rendering application; however, often the repair is inadequate, resorting to the use of incompatible materials, including cement-based mortars. It has been observed that such interventions, in walls that until that day only had presented natural ageing issues, created new problems, much more dangerous for the building than the previous ones, causing serious deficiencies in this type of construction. One of the problems is that the detachment of the new cement-based mortar rendering only occurs after some time but, until that occurrence, degradations develop in the wall itself. When the render detaches, instead of needing only a new render, the surface has to be repaired in depth, with a repair mortar. Consequently, it has been stablished that the renders, and particularly repair mortars, should have physical, mechanical and chemical properties similar to those of the rammed earth walls. This article intends to contribute to a better knowledge of earth-based mortars used to repair the surface of rammed earth walls. The studied mortars are based on four types of earth: three of them were collected from non-deteriorated parts of walls of unstabilized rammed earth buildings located in Alentejo region, south of Portugal; the fourth is a commercial earth, consisting mainly of clay. Other components were also used, particularly: sand to control shrinkage; binders stabilizers such as dry hydrated air-lime, natural hydraulic lime, Portland cement and natural cement; as well as natural vegetal fibers (hemp fibers). The experimental analysis of the mortars in the fresh state consisted in determining the consistency by flow table and the bulk density. In the hardened state, the tests made it possible to evaluate the following properties: linear and volumetric shrinkage; capillary water absorption; drying capacity; dynamic modulus of elasticity; flexural and compressive strength.

Historic and potential technology transition paths of grid battery storage: Co-evolution of energy grid, electric mobility and batteries

Scarcity of fuels, changes in environmental policy and in society increased the interest in generating electric energy from renewable energy sources (RES) for a sustainable energy supply in the future. The main problem of RES as solar and wind energy, which represent a main pillar of this transition, is that they cannot supply constant power output. This results inter alia in an increased demand of backup technologies as batteries to assure electricity system safety. The diffusion of energy storage technologies is highly dependent on the energy system and transport transition pathways which might lead to a replacement or reconfiguration of embedded socio-technical practices and regimes (by creating new standards or dominant designs, changing regulations, infrastructure and user patterns). The success of this technology is dependent on hardly predictable future technical advances, actor preferences, development of competing technologies and designs, diverging interests of actors, future cost efficiencies, environmental performance, the evolution of market demand and design and evolution of our society.

Plasma nitriding of AA2011 alloy and surface characterization by NDT techniques

Al-Cu alloys are widely used in the aerospace and automotive industries due to their high specific strength in some tempered conditions. However, due to poor corrosion and wear resistance, they are often anodized and/or painted. Plasma nitriding has been proposed as an alternative, though the developments in this technique are still in a recent stage for Al alloys. Electrical characterization techniques are well implemented NDTs in the industry because of good accuracy associated with lower cost, compared to other methods. Some, like eddy currents and 4-point probe techniques, are often used in coating inspection. The objective of this study was to perform Al nitriding at low temperatures to minimize the tempering initial condition damage and to assess the feasibility of eddy currents technique as a method for evaluating surface properties. The work developed can be divided in two stages. The first one was the process tuning, done at the Shibaura Institute of Technology, in Tokyo; and the second was the electrical characterization done in Faculdade de Ciências e Tecnologia, UNL. Low temperature nitriding of AA2011 alloy specimens was successfully achieved. Electrical conductivity results show that lift-off measurements by eddy currents testing can be related to surface properties.

ReedCob – An eco-efficient building technology for monolithic walls based on earth and reeds

4th Conference COST ACTION FP1303 – Designing with Bio-based Materials – Challenges and opportiunities. INIA – CSIC, Madrid, 24-25 February 2016. Book of abstracts, T.Troya, J.Galván, D.Jones (Eds.), INIA and IETcc – CSIS, pg. 79-80 (ISBN: 978-91-88349-16-3)

Amadeus IT holdings information technology

Equity research report

Royal Philips Medical Technology

Equity research report

Decisions of technology innovation: the role of indicators

This work presents research conducted to understand the role of indicators in decisions of technology innovation. A gap was detected in the literature of innovation and technology assessment about the use and influence of indicators in this type of decision. It was important to address this gap because indicators are often frequent elements of innovation and technology assessment studies. The research was designed to determine the extent of the use and influence of indicators in decisions of technology innovation, to characterize the role of indicators in these decisions, and to understand how indicators are used in these decisions. The latter involved the test of four possible explanatory factors: the type and phase of decision, and the context and process of construction of evidence. Furthermore, it focused on three Portuguese innovation groups: public researchers, business R&D&I leaders and policymakers. The research used a combination of methods to collect quantitative and qualitative information, such as surveys, case studies and social network analysis. This research concluded that the use of indicators is different from their influence in decisions of technology innovation. In fact, there is a high use of indicators in these decisions, but lower and differentiated differences in their influence in each innovation group. This suggests that political-behavioural methods are also involved in the decisions to different degrees. The main social influences in the decisions came mostly from hierarchies, knowledge-based contacts and users. Furthermore, the research established that indicators played mostly symbolic roles in decisions of policymakers and business R&D&I leaders, although their role with researchers was more differentiated. Indicators were also described as helpful instruments to conduct a reasonable interpretation of data and to balance options in innovation and technology assessments studies, in particular when contextualised, described in detail and with discussion upon the options made. Results suggest that there are four main explanatory factors for the role of indicators in these decisions: First, the type of decision appears to be a factor to consider when explaining the role of indicators. In fact, each type of decision had different influences on the way indicators are used, and each type of decision used different types of indicators. Results for policy-making were particularly different from decisions of acquisition and development of products/technology. Second, the phase of the decision can help to understand the role indicators play in these decisions. Results distinguished between two phases detected in all decisions – before and after the decision – as well as two other phases that can be used to complement the decision process and where indicators can be involved. Third, the context of decision is an important factor to consider when explaining the way indicators are taken into consideration in policy decisions. In fact, the role of indicators can be influenced by the particular context of the decision maker, in which all types of evidence can be selected or downplayed. More importantly, the use of persuasive analytical evidence appears to be related with the dispute existent in the policy context. Fourth and last, the process of construction of evidence is a factor to consider when explaining the way indicators are involved in these decisions. In fact, indicators and other evidence were brought to the decision processes according to their availability and capacity to support the different arguments and interests of the actors and stakeholders. In one case, an indicator lost much persuasion strength with the controversies that it went through during the decision process. Therefore, it can be argued that the use of indicators is high but not very influential; their role is mostly symbolic to policymakers and business decisions, but varies among researchers. The role of indicators in these decisions depends on the type and phase of the decision and the context and process of construction of evidence. The latter two are related to the particular context of each decision maker, the existence of elements of dispute and controversies that influence the way indicators are introduced in the decision-making process.

Therapeutics bioconjugates: evaluation of iminoboronates as payload delivery system for cancer

The advent of bioconjugation impacted deeply the world of sciences and technology. New biomolecules were found, biological processes were understood, and novel methodologies were formed due to the fast expansion of this area. The possibility of creating new effective therapies for diseases like cancer is one of big applications of this now big area of study. Off target toxicity was always the problem of potent small molecules with high activity towards specific tumour targets. However, chemotherapy is now selective due to powerful linkers that connect targeting molecules with affinity to interesting biological receptors and cytotoxic drugs. This linkers must have very specific properties, such as high stability in plasma, no toxicity, no interference with ligand affinity nor drug potency, and at the same time, be able to lyse once inside the target molecule to release the therapeutic warhead. Bipolar environments between tumour intracellular and extracellular medias are usually exploited by this linkers in order to complete this goal. The work done in this thesis explores a new model for that same task, specific cancer drug delivery. Iminoboronates were studied due to its remarkable selective stability towards a wide pH range and endogenous molecules. A fluorescence probe was design to validate this model by creating an Off/On system and determine the payload release location in situ. A process was optimized to synthetize the probe 8-(1-aminoethyl)-7-hydroxy-coumarin (1) through a reductive amination reaction in a microwave reactor with 61 % yield. A method to conjugate this probe to ABBA was also optimized, obtaining the iminoboronate in good yields in mild conditions. The iminoboronate model was studied regarding its stability in several simulated biological environments and each half-life time was determined, showing the conjugate is stable most of the cases except in tumour intracellular systems. The construction of folate-ABBA-coumarin bioconjugate have been made to complete this evaluation. The ability to be uptaken by a cancer cell through endocytosis process and the conjugation delivery of coumarin fluorescence payload are two features to hope for in this construct.