Analysis and treatment of a nineteenth century oil painting

This thesis focused on the study and treatment of a 19th century female portrait in oil from ECOMUSEU Municipal do Seixal, Portugal. The portrait, which depicts Isabel Maria Lourenço Affonso was in poor condition and a large strip of paint and canvas was missing (approximately 9cm by 66cm, almost 11% of the total surface area). The portrait is a companion piece to a male portrait (the relationship was established as part of this study), therefore a technical study of both paintings was considered essential to support the choices made during the treatment. The project involved three main areas: - The study of the history, condition, materials and techniques of both paintings. This allowed their comparison and understanding of their relationship; - The treatment of Isabel Maria Lourenço Affonso. The choices made and problems encountered are described. - The production of a replacement for the missing strip of paint and canvas. The practical solution developed to overcome such an unusual challenge is described along with the creative and flexible thinking required. Because not all traditional infill materials cope well on a mechanical level with thin layers over a very large surface (many are too brittle), strict criteria had to be employed to choose the appropriate material. The primary goal was to find a fill which would remain flexible and be capable of accepting surface texture, such that there would be a good visual match with the painting. Analysis and testing was carried out to evaluate the physical properties of the fill material chosen, BEVA® Gesso-P. The successful creation of the replacement strip has resulted in two publications and one presentation: Publication pending in The Picture Restorer, Leslie Carlyle, Raquel Marques, Isabel Pombo Cardoso and Sara Babo, “Creating a Textured Replacement Strip for the Missing Lower Portion of an Oil Portrait: Problem Solving and Practical Solutions”. Abstract accepted for presentation and publication, International Meeting on Retouching of Cultural Heritage (2RECH), Raquel Marques, Leslie Carlyle and Isabel Pombo Cardoso, “Textured Replacement Strip for a Missing Portion of a Portrait: Problem Solving and Practical Solutions”.

Mechanical characterization of aortas using 2D ultrasound elastography

Rupture of aortic aneurysms (AA) is a major cause of death in the Western world. Currently, clinical decision upon surgical intervention is based on the diameter of the aneurysm. However, this method is not fully adequate. Noninvasive assessment of the elastic properties of the arterial wall can be a better predictor for AA growth and rupture risk. The purpose of this study is to estimate mechanical properties of the aortic wall using in vitro inflation testing and 2D ultrasound (US) elastography, and investigate the performance of the proposed methodology for physiological conditions. Two different inflation experiments were performed on twelve porcine aortas: 1) a static experiment for a large pressure range (0 – 140 mmHg); 2) a dynamic experiment closely mimicking the in vivo hemodynamics at physiological pressures (70 – 130 mmHg). 2D raw radiofrequency (RF) US datasets were acquired for one longitudinal and two cross-sectional imaging planes, for both experiments. The RF-data were manually segmented and a 2D vessel wall displacement tracking algorithm was applied to obtain the aortic diameter–time behavior. The shear modulus G was estimated assuming a Neo-Hookean material model. In addition, an incremental study based on the static data was performed to: 1) investigate the changes in G for increasing mean arterial pressure (MAP), for a certain pressure difference (30, 40, 50 and 60 mmHg); 2) compare the results with those from the dynamic experiment, for the same pressure range. The resulting shear modulus G was 94 ± 16 kPa for the static experiment, which is in agreement with literature. A linear dependency on MAP was found for G, yet the effect of the pressure difference was negligible. The dynamic data revealed a G of 250 ± 20 kPa. For the same pressure range, the incremental shear modulus (Ginc) was 240 ± 39 kPa, which is in agreement with the former. In general, for all experiments, no significant differences in the values of G were found between different image planes. This study shows that 2D US elastography of aortas during inflation testing is feasible under controlled and physiological circumstances. In future studies, the in vivo, dynamic experiment should be repeated for a range of MAPs and pathological vessels should be examined. Furthermore, the use of more complex material models needs to be considered to describe the non-linear behavior of the vascular tissue.

Characterization tests for insulation boards made from corn cob and natural glues

In recent years there has been a growing interest in developing news solutions for more ecologic and efficient construction, including natural, renewable and local materials, thus contributing in the search for more efficient, economic and environmentally friendly construction. Several authors have assessed the possibility of using various agricultural sub products or wastes, as part of the effort of the scientific community to find alternative and more ecologic construction materials. Corn cob is an agricultural waste from a very important worldwide crop. Natural glues are made from natural materials, non-mineral, that can be used as such or after some modifications to achieve the behaviour and performance required. Two examples of these natural glues are casein and wheat flour-based glues that were used in the present study. Boards with different compositions were manufactured, having as variables the type of glue, the dimension of the corn cob particles and the features of the pressing process. The tests boards were characterized with physical and mechanical tests, such as thermal conductivity (λ) with a ISOMET 2104 and 60 mm diameter contact probe, density (ρ) based on EN 1602:2013, surface hardness (SH) with a PCE Shore A durometer, surface resistance (SR) with a PROCEQ PT pendular sclerometer, bending behaviour (σ) based on EN 12089:2013, compression behaviour (σ10) based on EN 826:2013 and resilience (R) based on EN 1094-1:2008, with a Zwick Rowell bending equipment with 2 kN and 50 kN load cells (Fig. 1), dynamic modulus of elasticity (Ed) with a Zeus Resonance Meter equipment (Fig. 5) based on NP EN 14146:2006 and water vapour permeability (δ) based on EN 12086:2013. The various boards produced were characterized according to the tests and the ones with the best results were C8_c8 (casein glue, grain size 2,38-4,76 mm, cold pressing for 8 hours), C8_c4 (casein glue, grain size 2,38-4,76 mm, cold pressing for 4 hours), F8_h0.5 (wheat flour glue, grain size 2,38-4,76 mm, hot pressing for 0,5 hours), FEV8_h0.5 (wheat flour, egg white and vinegar glue, grain size 2,38-4,76 mm, hot pressing for 0,5 hours) and FEVH68_c4 (wheat flour, egg white, vinegar and 6 g of sodium hydroxide glue, grain size 2,38-4,76 mm, cold pressing for 4 hours). Taking into account the various boards produced and respective test results the type of glue and the pressure and pressing time are very important factors which strongly influence the final product. The results obtained confirmed the initial hypotheses that these boards have potential as a thermal and, eventually, acoustic insulation material, to use as coating or intermediate layer on walls, floors or false ceilings. This type of board has a high mechanical resistance when compared with traditional insulating materials.The integrity of these boards seems to be maintained even in higher humidity environments. However, due to biological susceptibility and sensitivity to water, they would be more adequate for application in dry interior conditions.

Empirically testing the dimensions of consumer trust in e-commerce

In the fields of marketing and general management, many are the contributions of literature relating trust and e‐commerce. Trust is perceived as an issue that concerns the consumers’ intention to purchase. As so, in this research, a path model is empirically tested in order to develop solutions for Internet vendors on how to deal with consumers and increase their trust. The path model measures how the dimensions of trust, named as competence, integrity and benevolence positively influence the overall trust of the consumers and at the same time how the sources of trust – consumer characteristics, firm characteristics, website infrastructure and interactions influence those dimensions. The data used to test the model was collected in Portugal, through 365 valid cases. Findings revealed that consumers, which have high level of overall trust, are more likely to intent to purchase online.

Produção de misturas betuminosas a quente com incorporação de material fresado

A incorporação de materiais reciclados na construção de estradas, como substituição de materiais virgens é percebida como uma oportunidade de economizar recursos, e evitar o impacto associado à sua extração e transporte. Desta forma, a incorporação de material fresado (do termo inglês RAP - Reclaimed Asphalt Pavement) em misturas betuminosas produzidas a quente em central tem sido uma alternativa satisfatória. Neste trabalho, foram estudadas três misturas betuminosas do tipo macadame betuminoso (AC 20 base 35/50), tradicional e com taxas de incorporação de RAP de 10% e 20%, com o objetivo de efetuar uma análise comparativa do seu comportamento. Começou-se por realizar um estudo Marshall de forma a determinar a percentagem ótima de betume a usar em cada mistura e, posteriormente, a composição foi transposta para central para o seu fabrico. No final foram realizados ensaios de caracterização mecânica sobre as misturas para avaliar o seu desempenho, através de ensaios de sensibilidade à água, módulo de rigidez, resistência à fadiga e à deformação permanente. Esta dissertação teve o apoio da empresa Tecnovia – Sociedade de Empreitadas S.A., com a disponibilização de instalações e materiais para o trabalho experimental. De acordo com os resultados obtidos, é possível concluir que as misturas recicladas apresentaram um comportamento satisfatório, quando comparado com as misturas tradicionais.

Compaction quality control on site of earthworks - A comparative study

The capacity to use geologic materials (soil and rock) that are available in the surrounding environment is inherent to the human civilization and has contributed to the evolution of societies throughout the course of history. The use of these materials in the construction of structures such as houses, roads, railways or dams, stirred the improvement of socioeconomic and environmental conditions. Several reports of structural problems on embankments can be found throughout history. A considerable number of those registers can be linked to inadequate compaction, demonstrating the importance of guaranteeing a suitable quality of soil compaction. Various methodologies and specifications of compaction quality control on site of earthworks, based on the fill moisture content and dry unit weight, were developed during the 20th century. Two widely known methodologies are the conventional and nuclear techniques. The conventional methods are based on the use of the field sand cone test (or similar) and sampling of material for laboratory-based testing to evaluate the fill dry unit weight and water content. The nuclear techniques measure both parameters in the field using a nuclear density gauge. A topic under discussion in the geotechnical community, namely in Portugal, is the comparison between the accuracy of the nuclear gauge and sand cone test results for assessing the compaction and density ratio of earth fills, particularly for dams. The main purpose of this dissertation is to compare both of them. The data used were acquired during the compaction quality control operations at the Coutada/Tamujais dam trial embankment and core construction. This is a 25 m high earth dam located in Vila Velha de Rodão, Portugal. To analyse the spatial distribution of the compaction parameters (water content and compaction ratio), a 3D model was also developed. The main results achieved are discussed and finally some considerations are put forward on the suitability of both techniques to ensure fill compaction quality and on additional research to complement the conclusions obtained.

Conservar depois da catástrofe. O caso dos documentos queimados do antigo Arquivo Histórico do Museu Bocage: caracterização material e proposta de um protocolo de intervenção

Tendo como caso de estudo um conjunto documental do Arquivo Histórico dos Museus da Universidade de Lisboa (AHMUL) – Museu Nacional de História Natural e da Ciência (MUHNAC), anteriormente fazendo parte do antigo Arquivo Histórico do Museu Bocage – fortemente atingido por um incêndio em 1978, o objectivo principal desta investigação é dar início à pesquisa e explorar a possibilidade de aplicação de métodos não invasivos de restauro digital, como a técnica de digitalização volumétrica (volumetric scanning), para a recuperação da informação escrita na parte mais deteriorada do arquivo; e propor métodos de estabilização/recuperação do seu suporte físico, usando técnicas tradicionais de conservação e restauro. Assim, o objectivo deste estudo não é apenas rever métodos de recuperação da informação para estes documentos tidos como perdidos, mas também propor uma forma de recuperar, tanto quanto possível, o seu suporte original. Será realizada a caracterização material da colecção, com recurso a métodos de exame e análise e o diagnóstico de conservação da parte da colecção mais deteriorada, bem como uma contextualização histórica sobre o arquivo e as condições do incêndio. Como conclusões principais salienta-se a confirmação da possibilidade de aplicação de técnicas de digitalização, os resultados promissores de outras técnicas como a fotografia de infravermelho com recurso adicional a software de processamento da imagem e o uso da imagem multiespectral em documentos carbonizados, além do estabelecimento de uma proposta de protocolo de intervenção para documentos queimados, com recurso a dois éteres de celulose, com diferentes solventes (água e etanol) de acordo com a solubilidade dos meios de escrita. Pretendeu-se ainda com este estudo contribuir para a divulgação da existência deste fundo do AHMUL em específico, tendo sido fundamental a realização, após 37 anos, do primeiro registo e compilação de fontes documentais sobre o incêndio de 18 de março de 1978, um facto tão relevante para a Memória do MUHNAC e dos Museus de Portugal.

Improving the early diagnostic of prostate cancer by multiple biomarker detection with new biosensing devices

Prostate cancer (PCa) is the most common form of cancer in men, in Europe (World Health Organization data). The most recent statistics, in Portuguese territory, confirm this scenario, which states that about 50% of Portuguese men may suffer from prostate cancer and 15% of these will die from this condition. Its early detection is therefore fundamental. This is currently being done by Prostate Specific Antigen (PSA) screening in urine but false positive and negative results are quite often obtained and many patients are sent to unnecessary biopsy procedures. This early detection protocol may be improved, by the development of point-of-care cancer detection devices, not only to PSA but also to other biomarkers recently identified. Thus, the present work aims to screen several biomarkers in cultured human prostate cell lines, serum and urine samples, developing low cost sensors based on new synthetic biomaterials. Biomarkers considered in this study are the following: prostate specific antigen (PSA), annexin A3 (ANXA3), microseminoprotein-beta (MSMB) and sarcosine (SAR). The biomarker recognition may occurs by means of molecularly imprinted polymers (MIP), which are a kind of plastic antibodies, and enzymatic approaches. The growth of a rigid polymer, chemically stable, using the biomarker as a template allows the synthesis of the plastic antibody. MIPs show high sensitivity/selectivity and present much longer stability and much lower price than natural antibodies. This nanostructured material was prepared on a carbon solid. The interaction between the biomarker and the sensing-material produces electrical signals generating quantitative or semi-quantitative data. These devices allow inexpensive and portable detection in point-of-care testing.

AS COSTUREIRAS, AS QUEENS E OS SEUS MANTOS: DESTERRITORIALIZAÇÃO, CULTURA MATERIAL E CONSTRUÇÃO DO LUGAR

Durante as décadas de 1980 e de 1990 a noção de lugar foi, na literatura antropológica, sujeita a uma abordagem crítica que debateu as dimensões metodológicas e conceptuais envolvidas na sua construção. No seguimento dessa abordagem, surgiram propostas de trabalho que, de maneiras muito diversas, conseguiram ultrapassar as limitações das concepções mais clássicas da figura do lugar. Essas propostas revelaram, no entanto, que mesmo quando estamos face a uma lógica de desterritorialização, a figura do lugar pode reaparecer (embora obviamente transmutada, visto construir-se no interior de outras lógicas sociais, culturais e económicas). Partindo de uma etnografia realizada na Ilha do Pico, o texto explora algumas das inovações, provenientes dos EUA no início do século XX, que foram introduzidas nas Festas do Espírito Santo. A principal inovação prende-se com a emergência de novos personagens: as rainhas (“queens”) coroadas durante o ritual, seguidas pelas costureiras indispensáveis à confecção dos seus vestidos e mantos. Centrado nos processos de feitura dos mantos, o texto pretende mostrar como a cultura material local se constrói e se transforma no interior de um movimento transcontinental constante de pessoas, rituais, coisas e técnicas. Num contexto transnacional, a mobilidade das pessoas pode objetificar-se em coisas que são feitas localmente, participando assim a desterritorialização na construção do lugar.

Geopolymers as infill material for conservation of azulejos

The restoration materials currently used to fill gaps in architectural historical azulejos (e.g. lime or organic resin pastes) usually show serious drawbacks in terms of compatibility, effectiveness and durability. The existing solutions do not fully protect azulejos in outdoor conditions and frequently result in further deterioration. Geopolymers can be a potential solution for azulejo lacunae infill given the chemical-mineralogical similitude to the ceramic body, and also the durability and versatile range of physical properties that can be obtained through the manipulation of their formulation and curing conditions. This work presents and discusses the viability of the use of geopolymeric pastes to fill lacunae in azulejos or to act as “cold” cast ceramic tile surrogates reproducing missing azulejo fragments. The formulation of geopolymers, namely the type of activators, the aluminosilicate source, the amount of water (to meet adequate workability requirements) and curing conditions were studied. The need for post-curing desalination was also considered envisaging their application in the restoration of outdoor architectural historical azulejos frequently exposed to adverse environmental conditions. The possible advantages and disadvantages of the use of geopolymers in the conservation of azulejos are also discussed. Several techniques were used to study the chemical and physical behavior of geopolymers, namely FT-IR, XRD, MIP, SEM-EDS, WDXRF, electrical conductivity, open porosity, bending strength, adhesion strength, water vapour permeability, thermal expansion and hydric expansion. The results indicate that geopolymers are a promising material for restoration of azulejos, exhibiting some properties, such as adhesion to the ceramic substrate, higher than inorganic materials used nowadays, such as aerial lime based pastes.

The early metallurgy in Southwestern Iberia: metals from the Chalcolithic Settlement of São Pedro (Redondo)

Archaeological excavations carried out in the archaeological site of São Pedro (Southern Portugal) revealed a Chalcolithic settlement occupied in different moments of the 3rd millennium BC. The material culture recovered includes different types of materials, such as ceramics, lithics and metals. The later comprises about 30 artefacts with different typologies such as tools (e.g. awls, chisels and a saw) and weapons (e.g. daggers and arrowheads) mostly belonging to the 2nd and 3rd quarter of the 3rd millennium BC. In the present work the collection of chalcolithic metallic artefacts recovered in São Pedro was characterized. Analytical studies involved micro energy dispersive X-ray fluorescence spectrometry (micro-EDXRF) to determine elemental composition, together with optical microscopy and Vickers microhardness testing for microstructural characterisation and hardness determination. Main results show copper with variable amounts of arsenic and very low content of other impurities, such as iron. Moreover, nearly half of the collection is composed by arsenical copper alloys (As > 2 wt.%) and an association was found between arsenic content and typology since the weapons group (mostly daggers) present higher values than tools (mostly awls). These results suggest some criteria in the selection of arsenic-rich copper ores or smelting products. Furthermore, after casting an artefact would have been hammered, annealed and sometimes, finished with a hammering operation. Additionally, microstructural variations in this collection reveal somewhat different operational conditions during casting, annealing and forging, as expected in such a primitive metallurgy. Moreover the operational sequence seems to be used to achieve the required shape to the object, rather than to intentionally make the alloy harder. Overall, this study suggests that Chalcolithic metallurgists might have a poor control of the addition of arsenic and/or were unable to use this element to increase the hardness of tools and weapons. Finally, the compositions, manufacturing processes and hardness were compared to those from neighbouring regions and different chronological periods.

Building 3D City Models: Testing and Comparing Laser Scanning and Low-Cost UAV Data Using FOSS Technologies

Contém resumo

Al-doped ZnO ceramic sputtering targets based on nanocrystalline powders produced by emulsion detonation synthesis – deposition and application as a transparent conductive oxide material

Transparent conducting oxides (TCOs) have been largely used in the optoelectronic industry due to their singular combination of low electrical resistivity and high optical transmittance. They are usually deposited by magnetron sputtering systems being applied in several devices, specifically thin film solar cells (TFSCs). Sputtering targets are crucial components of the sputtering process, with many of the sputtered films properties dependent on the targets characteristics. The present thesis focuses on the development of high quality conductive Al-doped ZnO (AZO) ceramic sputtering targets based on nanostructured powders produced by emulsion detonation synthesis method (EDSM), and their application as a TCO. In this sense, the influence of several processing parameters was investigated from the targets raw-materials synthesis to the application of sputtered films in optoelectronic devices. The optimized manufactured AZO targets present a final density above 99 % with controlled grain size, an homogeneous microstructure with a well dispersed ZnAl2O4 spinel phase, and electrical resistivities of ~4 × 10-4 Ωcm independently on the Al-doping level among 0.5 and 2.0 wt. % Al2O3. Sintering conditions proved to have a great influence on the properties of the targets and their performance as a sputtering target. It was demonstrated that both deposition process and final properties of the films are related with the targets characteristics, which in turn depends on the initial powder properties. In parallel, the influence of several deposition parameters in the film´s properties sputtered from these targets was investigated. The sputtered AZO TCOs showed electrical properties at room temperature that are superior to simple oxides and comparable to a reference TCO – indium tin oxide (ITO), namely low electrical resistivity of 5.45 × 10-4 Ωcm, high carrier mobility (29.4 cm2V-1s-1), and high charge carrier concentration (3.97 × 1020 cm-3), and also average transmittance in the visible region > 80 %. These superior properties allowed their successful application in different optoelectronic devices.

Torrefação de biomassa de Arundo donax L. e de Phoenix canariensis com vista à sua valorização energética ou material

A torrefação é vista como um pré-tratamento térmico que introduz modificações na biomassa, ou em resíduos de biomassa, que facilitam o seu processamento mecânico e aumentam a sua estabilidade e densidade energética, potenciando, assim, uma valorização posterior. Neste trabalho, estudou-se o impacte da torrefação na gama de 200 a 350 ºC e tempos de residência entre 15 e 90 min nas propriedades da biomassa proveniente da herbácea Arundo donax L. e das palmeiras Phoenix canariensis, espécies muito abundantes em vários locais do país, tendo em vista a sua posterior valorização. A proliferação descontrolada do arundo e a praga do escaravelho das palmeiras leva a que estas espécies sejam alvo de frequentes operações de remoção. A sua estrutura altamente fibrosa dificulta e encarece estas operações, que acarretam custos significativos para as câmaras municipais, e não se conhecem medidas para a sua valorização material ou energética. A torrefação foi também aplicada a peletes de resíduos de pinheiro, na gama de 200 a 250 ºC e com tempos de residência de 30 e 60 min, para averiguar o seu impacte na qualidade desse biocombustível sólido. A torrefação permitiu obter peletes mais resistentes à biodegradação, devido à redução do teor de humidade para valores residuais, sem aumentar significativamente o seu teor de cinzas e sem afetar de forma relevante a sua durabilidade, o teor de finos ou a densidade aparente. Com a biomassa de arundo e de palmeira obtiveram-se produtos com maior poder calorífico e com melhor moabilidade. No entanto, a acentuada diminuição dos rendimentos mássico e energético e o elevado teor de cinzas constrangem a sua utilização como biocombustíveis sólidos. Desta forma, optou-se por testar a sua valorização como adsorventes do corante azul de metileno, bastante comum, por exemplo, na indústria têxtil, nos curtumes ou nas industrias do papel. Os estudos de adsorção revelaram maior afinidade pelo corante por parte da biomassa sujeita a torrefação mais ligeira, com eficiências de remoção muito próximas das do carvão ativado comercial, para concentrações iniciais de corante até 200 mg/L. As isotérmicas foram melhor ajustadas ao modelo de Langmuir, que revelou capacidades máximas de adsorção na monocamada entre 59,92 e 92,68 mg/g, tendo as curvas de cinética sido melhor descritas pelo modelo de pseudo-segunda ordem. A adsorção é bastante rápida nos primeiros minutos, essencialmente devido a atrações eletrostáticas, sendo inicialmente controlada pela difusão no filme e depois pela difusão nos poros. Os adsorventes revelaram seletividade por um corante catiónico e permitiram dessorção de corante, ao contrário do verificado com o carvão ativado comercial, o que é um aspeto da maior relevância tendo em mente a regeneração do adsorvente e a recuperação do corante.

Testing for tail breaks in currency returns

In this work project we study the tail properties of currency returns and analyze whether changes in the tail indices of these series have occurred over time as a consequence of turbulent periods. Our analysis is based on the methods introduced by Quintos, Fan and Phillips (2001), Candelon and Straetmans (2006, 2013), and their extensions. Specifically, considering a sample of daily data from December 31, 1993 to February 13, 2015 we apply the recursive test in calendar time (forward test) and in reverse calendar time (backward test) and indeed detect falls and rises in the tail indices, signifying increases and decreases in the probability of extreme events.