Analysis and treatment of a nineteenth century oil painting

This thesis focused on the study and treatment of a 19th century female portrait in oil from ECOMUSEU Municipal do Seixal, Portugal. The portrait, which depicts Isabel Maria Lourenço Affonso was in poor condition and a large strip of paint and canvas was missing (approximately 9cm by 66cm, almost 11% of the total surface area). The portrait is a companion piece to a male portrait (the relationship was established as part of this study), therefore a technical study of both paintings was considered essential to support the choices made during the treatment. The project involved three main areas: - The study of the history, condition, materials and techniques of both paintings. This allowed their comparison and understanding of their relationship; - The treatment of Isabel Maria Lourenço Affonso. The choices made and problems encountered are described. - The production of a replacement for the missing strip of paint and canvas. The practical solution developed to overcome such an unusual challenge is described along with the creative and flexible thinking required. Because not all traditional infill materials cope well on a mechanical level with thin layers over a very large surface (many are too brittle), strict criteria had to be employed to choose the appropriate material. The primary goal was to find a fill which would remain flexible and be capable of accepting surface texture, such that there would be a good visual match with the painting. Analysis and testing was carried out to evaluate the physical properties of the fill material chosen, BEVA® Gesso-P. The successful creation of the replacement strip has resulted in two publications and one presentation: Publication pending in The Picture Restorer, Leslie Carlyle, Raquel Marques, Isabel Pombo Cardoso and Sara Babo, “Creating a Textured Replacement Strip for the Missing Lower Portion of an Oil Portrait: Problem Solving and Practical Solutions”. Abstract accepted for presentation and publication, International Meeting on Retouching of Cultural Heritage (2RECH), Raquel Marques, Leslie Carlyle and Isabel Pombo Cardoso, “Textured Replacement Strip for a Missing Portion of a Portrait: Problem Solving and Practical Solutions”.

Analysis and visualization of energy use for university campus

The reduction of greenhouse gas emissions is one of the big global challenges for the next decades due to its severe impact on the atmosphere that leads to a change in the climate and other environmental factors. One of the main sources of greenhouse gas is energy consumption, therefore a number of initiatives and calls for awareness and sustainability in energy use are issued among different types of institutional and organizations. The European Council adopted in 2007 energy and climate change objectives for 20% improvement until 2020. All European countries are required to use energy with more efficiency. Several steps could be conducted for energy reduction: understanding the buildings behavior through time, revealing the factors that influence the consumption, applying the right measurement for reduction and sustainability, visualizing the hidden connection between our daily habits impacts on the natural world and promoting to more sustainable life. Researchers have suggested that feedback visualization can effectively encourage conservation with energy reduction rate of 18%. Furthermore, researchers have contributed to the identification process of a set of factors which are very likely to influence consumption. Such as occupancy level, occupants behavior, environmental conditions, building thermal envelope, climate zones, etc. Nowadays, the amount of energy consumption at the university campuses are huge and it needs great effort to meet the reduction requested by European Council as well as the cost reduction. Thus, the present study was performed on the university buildings as a use case to: a. Investigate the most dynamic influence factors on energy consumption in campus; b. Implement prediction model for electricity consumption using different techniques, such as the traditional regression way and the alternative machine learning techniques; and c. Assist energy management by providing a real time energy feedback and visualization in campus for more awareness and better decision making. This methodology is implemented to the use case of University Jaume I (UJI), located in Castellon, Spain.

Demora média no tratamento da pneumonia adquirida na comunidade : estudo sobre os hospitais públicos portugueses entre 2009 e 2011

RESUMO - Contexto: O presente estudo teve como objetivo apurar a demora média (DM) em doentes admitidos com pneumonia adquirida de comunidade (PAC), nos hospitais públicos portugueses, que tiveram alta durante os anos de 2009, 2010 e 2011, identificar se esta é influenciada por um grupo de fatores selecionados para o efeito e determinar se existe margem para a reduzir nos hospitais com uma DM mais elevada, através da comparação da mesma com as respetivas taxas de readmissão até 30 dias após a alta. Metodologia: Para responder aos objetivos definidos recorreu-se à base de dado dos resumos de alta, referente aos anos de 2009, 2010 e 2011, tendo-se selecionado, para o efeito, todos os episódios de internamento com diagnóstico de admissão de PAC. O estudo considerou como medidas “chave” a DM e a taxa de readmissão até 30 dias após alta. Para identificar a influência de um conjunto de fatores na duração de internamento utilizaram-se duas abordagens: análise descritiva dos dados e análise estatística dos dados, com recurso a uma Regressão Linear Múltipla. Numa última fase e com recurso à análise descritiva dos resultados obtidos, procedeu-se à comparação da taxa de readmissão até 30 dias após alta, por hospital, com as DM de internamento que mais se distanciaram das DM nacional e corrigida da população em estudo. Resultados: Constatou-se que a no tratamento da PAC, em Portugal, entre 2009 e 2011, não sofreu em termos globais grandes oscilações, tendo registado um valor de 9,47 dias nos três anos em análise. Concluiu-se ainda existir uma elevada variabilidade da DM entre hospitais e por hospital. Apesar das limitações identificadas verificou-se que os fatores idade, sexo, quantidade de diagnósticos adicionais, quantidade de procedimentos, destino após alta e tipo de hospital têm influência sobre a duração de internamento dos doentes admitidos com PAC. Por fim conclui-se que os cinco hospitais com DM mais baixa apresentam, de uma forma geral e com exceção do hospital 44, uma taxa de readmissão até 30 dias após alta inferior aos hospitais com DM mais elevada. Conclusão: Os resultados apurados apontam no sentido de existir margem para reduzir a DM no tratamento da PAC, nos hospitais que registaram valores mais elevados entre 2009 e 2011, permitindo que os mesmos obtenham resultados mais custo-efetivos sem piorar os resultados em saúde, medidos pela taxa de readmissões até 30 dias após a alta e, simultaneamente garantindo que a qualidade dos cuidados prestados e a segurança do doente se mantêm nos níveis desejados e exigidos. Sugere-se, no entanto, que em estudos futuros se detalhem algumas das matérias abordadas neste estudo com o objetivo de completar ou corroborar os resultados apresentados.

Exporting a model of integrated disease management: A cross-case study analysis and application to Associação Protectora dos Diabéticos de Portugal

Although literature is lacking in the topic of internationalization of services, we manage to apply both the Uppsala model and the Eclectic Theory to the healthcare service. A cross-case study analysis with three international hospitals is done in order to define an internationalization pattern and conditions for a successful process. This is then applied to Associação Protectora dos Diabéticos de Portugal with the purpose of defining an internationalization strategy to the Association.

Analysis and implementation of a multi-ratio switched capacitor DC-DC converter for a supercapacitor power supply

An energy harvesting system requires an energy storing device to store the energy retrieved from the surrounding environment. This can either be a rechargeable battery or a supercapcitor. Due to the limited lifetime of rechargeable batteries, they need to be periodically replaced. Therefore, a supercapacitor, which has ideally a limitless number of charge/discharge cycles can be used to store the energy; however, a voltage regulator is required to obtain a constant output voltage as the supercapacitor discharges. This can be implemented by a Switched-Capacitor DC-DC converter which allows a complete integration in CMOS technology, although it requires several topologies in order to obtain a high efficiency. This thesis presents the complete analysis of four different topologies in order to determine expressions that allow to design and determine the optimum input voltage ranges for each topology. To better understand the parasitic effects, the implementation of the capacitors and the non-ideal effect of the switches, in 130 nm technology, were carefully studied. With these two analysis a multi-ratio SC DC-DC converter was designed with an output power of 2 mW, maximum efficiency of 77%, and a maximum output ripple, in the steady state, of 23 mV; for an input voltage swing of 2.3 V to 0.85 V. This proposed converter has four operation states that perform the conversion ratios of 1/2, 2/3, 1/1 and 3/2 and its clock frequency is automatically adjusted to produce a stable output voltage of 1 V. These features are implemented through two distinct controller circuits that use asynchronous time machines (ASM) to dynamically adjust the clock frequency and to select the active state of the converter. All the theoretical expressions as well as the behaviour of the whole system was verified using electrical simulations.

Analysis and Treatment of a male portrait in oil and a study of the size layer with reconstructions from Vibert’s recipe (1892)

This thesis project concentrated on both the study and treatment of an early 20th century male portrait in oil from Colecção Caixa Geral de Depósitos, Lisbon, Portugal. The portrait of Januário Correia de Almeida, exhibits a tear (approximately 4.0 cm by 2.3 cm) associated with paint loss on the right upper side, where it is possible to observe an unusually thick size layer (approximately 50 microns) and an open weave mesh canvas. Size layers made from animal glue remain subject to severe dimensional changes due to changes in relative humidity (RH), thereby affecting the stability of the painting. In this case, the response to moisture of the size layer is minimal and the painting is largely uncracked with very little active flaking. This suggests that the size layer has undergone pre-treatment to render it unresponsive to moisture or water. Reconstructions based on late nineteenth century recipes using historically appropriate materials are used to explore various options for modifying the characteristics of gelatine, some of which may relate to the Portrait’s size layer. The thesis is separated into two parts: Part 1: Describes the history, condition, materials and techniques of the painting. It also details the treatment of Januário Correia de Almeida as well as the choices made and problems encountered during the treatment. Part 2: Discusses the history of commercial gelatine production, the choice of the appropriate animal source to extract the collagen to produce reconstructions of the portrait’s size layer as well as the characterization of selected reconstructions. The execution of a shallow textured infill led to one publication and one presentation: Abstract accepted for presentation and publication, International Meeting on Retouching of Cultural Heritage (RECH3), Francisco Brites, Leslie Carlyle and Raquel Marques, ‘’Hand building a Low Profile Textured Fill for a Large Loss’’.

Analysis and treatment of a nineteenth century portrait, study of Artsorb® and a proposal for a microclimate frame

The present work is divided in two parts: Part 1 is focused on the analysis and treatment of a 19th century portrait of Domingos Affonso, which belongs to the Ecomuseu Municipal do Seixal; and Part 2, which is entitled “The Microclimate Frame Project” is focused on the study of Artsorb® and on the planning of a microclimate frame for the painting. In Part 1, a study of the painting’s materials was performed using complementary analytical techniques and the painting’s condition was carefully evaluated. The painting exhibited signs of mould growth, and a more detailed investigation was made of this topic to understand if the fungal community was active and if it represented a real danger to the painting. A treatment was proposed, appropriate to the painting’s condition. A description of the treatment carried out, comprising the treatment options, is also present in this section. Within the study of the microclimate frame, in Part 2, the study of the potential corrosiveness of Artsorb® was a central subject. Artsorb® sheets are one of the most widely used materials for buffering relative humidity fluctuations in microclimate frames and its reported excellent performance is enhanced by its availability in lightweight sheets that can be easily placed inside microclimate frames. However, concerns have arisen regarding the presence of the corrosive salt lithium chloride in the composition of this buffer. Consequently, the present work also aimed to understand the potential risks of using Artsorb® and the possibility of avoiding exposure of lithium chloride to the artworks through the use of Tyvek®. Results from the preliminary tests seem to indicate that Artsorb® releases lithium chloride into air. This study also showed that a Tyvek® cover over Artsorb® reduces but does not eliminate evidence of chlorine contamination, and it significantly reduces the effectiveness of the buffering material. Considering that Artsorb® appears to be unsuitable due to the release of the corrosive salt, that Tyvek® was not efficient as a barrier for lithium chloride or as a permeable material to enable the proper functioning of Artsorb®, the buffering material proposed for the use in the microclimate frames is silica gel without indicator. Based on the choice of buffering material, as a result of this study, a microclimate frame is proposed.

Analysis and design of sinusoidal quadrature RC-oscillators

Modern telecommunication equipment requires components that operate in many different frequency bands and support multiple communication standards, to cope with the growing demand for higher data rate. Also, a growing number of standards are adopting the use of spectrum efficient digital modulations, such as quadrature amplitude modulation (QAM) and orthogonal frequency division multiplexing (OFDM). These modulation schemes require accurate quadrature oscillators, which makes the quadrature oscillator a key block in modern radio frequency (RF) transceivers. The wide tuning range characteristics of inductorless quadrature oscillators make them natural candidates, despite their higher phase noise, in comparison with LC-oscillators. This thesis presents a detailed study of inductorless sinusoidal quadrature oscillators. Three quadrature oscillators are investigated: the active coupling RC-oscillator, the novel capacitive coupling RCoscillator, and the two-integrator oscillator. The thesis includes a detailed analysis of the Van der Pol oscillator (VDPO). This is used as a base model oscillator for the analysis of the coupled oscillators. Hence, the three oscillators are approximated by the VDPO. From the nonlinear Van der Pol equations, the oscillators’ key parameters are obtained. It is analysed first the case without component mismatches and then the case with mismatches. The research is focused on determining the impact of the components’ mismatches on the oscillator key parameters: frequency, amplitude-, and quadrature-errors. Furthermore, the minimization of the errors by adjusting the circuit parameters is addressed. A novel quadrature RC-oscillator using capacitive coupling is proposed. The advantages of using the capacitive coupling are that it is noiseless, requires a small area, and has low power dissipation. The equations of the oscillation amplitude, frequency, quadrature-error, and amplitude mismatch are derived. The theoretical results are confirmed by simulation and by measurement of two prototypes fabricated in 130 nm standard complementary metal-oxide-semiconductor (CMOS) technology. The measurements reveal that the power increase due to the coupling is marginal, leading to a figure-of-merit of -154.8 dBc/Hz. These results are consistent with the noiseless feature of this coupling and are comparable to those of the best state-of-the-art RC-oscillators, in the GHz range, but with the lowest power consumption (about 9 mW). The results for the three oscillators show that the amplitude- and the quadrature-errors are proportional to the component mismatches and inversely proportional to the coupling strength. Thus, increasing the coupling strength decreases both the amplitude- and quadrature-errors. With proper coupling strength, a quadrature error below 1° and amplitude imbalance below 1% are obtained. Furthermore, the simulations show that increasing the coupling strength reduces the phase noise. Hence, there is no trade-off between phase noise and quadrature error. In the twointegrator oscillator study, it was found that the quadrature error can be eliminated by adjusting the transconductances to compensate the capacitance mismatch. However, to obtain outputs in perfect quadrature one must allow some amplitude error.