Paleoalterações e cimentações nos depósitos continentais terciários de Portugal central: importância na interpretação de processos antigos

This paper describes the palaeoweathering, cementation, clay minerals association and other closely related characteristics of central Portugal allostratigraphic Tertiary units (SLD's), that can be used for palaeoclimatic interpretation and palaeoenvironmental reconstruction. Lateral and vertical changes in palaeosols are of value for improving our understanding of the autocyclic and allocyclic controls on sediment acumulation in an alluvial basin, but they can also have stratigraphic importance. In some cases it is concluded that the geomorphological setting may have been more decisive than climatic conditions to the production of the palaeoweathering. During late Palaeogene (SLD7-8), surface and near-surface silicification were developed on tectonically stable land surfaces of minimal local relief under a semi-arid climate; groundwater flow was responsible for some eodiagenesis calcareous accumulations, with the neoformation of palygorskite. Conditions during the Miocene (SLD9-11) were favourable for the smectization of the metamorphic basement and arenization of granites. Intense rubefaction associated with basement conversion into clay (illite and kaolinite), is ascribed to internal drainage during late Messinian-Zanclean (SLD12). During Piacenzian (SLD13) intense kaolinization and hydromorphism are typical, reflecting a more humid and hot temperate climate and important Atlantic fluvial drainage. Later on (Gelasian-early Pleistocene ?; SLD14). more cold and dry conditicns are interpreted, at the beginning of the fluvial incision sage. Silica cementation is identified in the upper Eocence-Oligocene ? (SLD18; the major period of silicification), middle to upper Miocene (SLD10)and upper Tortonian-Messinian (SLD11); these occurrences are compatible with either arid or semi-arid conditions and the establishment of a flat landscape upon which a silcrete was developed.

On the hydrogeology of the Lower Tagus Basin and its Cenozoic geologic evolution

The chemical features of the ground water in the Lower Tagus Cenozoic deposits are strongly influenced by lithology, by the velocity and direction of the water movement as well as by the localization of the recharge and discharge zones. The mineralization varies between 80 and 900 mg/l. It is minimal in the recharge zones and in the Pliocene sand and maximum in the Miocene carbonated and along the alluvial valley. Mineralization always reflects the time of permanence, the temperature and the pressure. The natural process of water mineralization is disturbed in agricultural areas because the saline concentration of the infiltration water exceeds that of the infiltrated rainwater. In the discharge zones, the rise of the more mineralized, some times thermal deep waters related to tectonic accidents give rise to anomalies in the distribution of the aquiferous system mineralization model. The diversity of the hydrochemical facies of the ground water may be related to several factors whose identification is some times difficult.

Employment of the side product of biodiesel production in the formation of surfactant like molecules

Dissertação apresentada na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa para obtenção do grau de Mestre em Engenharia Química e Bioquímica

Modelação fenomenológica de um motor Diesel marítimo para avaliar efeitos da mudança de combustível

Dissertação para obtenção do Grau de Mestre em Engenharia Mecânica

Análise termodinâmica de uma central de biomassa lenhosa

Dissertação para obtenção do Grau de Mestre em Engenharia Mecânica

Introducing Mobile Money in Rural Mozambique: Evidence from a Field Experiment*

The limitations of access to finance in Africa, together with the recent boom in cell phone use in that continent, created high expectations regarding the introduction of mobile money in many African countries. The success story of M-PESA in Kenya raised the bar further. We designed and conducted a field experiment to assess the impact of randomized mobile money dissemination in rural Mozambique. For this purpose we benefit from the fact that mobile money was only recently launched in the country, allowing for the identification of a pure control group. This paper reports on the first results of this ongoing project after the first wave of dissemination efforts in rural locations, which included the recruitment and training of mobile money agents, community meetings and theaters, as well as individual rural campaigning. Administrative and behavioral data both show clear adherence to the services in the treatment group. Financial literacy and trust outcomes are also positively affected by the treatment. We present behavioral evidence that the marginal willingness to remit was increased by the availability of mobile money. Finally, we observe a tendency for mobile money to substitute traditional alternatives for both savings and remittances.

Experimental Gravimetric Adsorption Equilibrium of n-Alkanes and Alkenes, Carbon Dioxide and Nitrogen in MIL-53(Al) and Zeolite 5A

Dissertação para obtenção do Grau de Mestre em Engenharia Química e Bioquímica

Experimental high-throughput adsorption unit for multi-evaluation of adsorbents for gas capture, storage and separation applications

Dissertação para obtenção do grau de Mestre em Engenharia Química e Bioquímica

Development of a "green process" for the isolation of natural functional extracts with anti-cancer activity - Application of high-pressure technology

Dissertação para obtenção do Grau de Mestre em Engenharia Química e Bioquímica

Upgrade of an experimental volumetric unit for gas adsorption equilibrium studies

In this work, a volumetric unit previously assembled by the research group was upgraded. This unit revamping was necessary due to the malfunction of the solenoid valves employed in the original experimental setup, which were not sealing the gas properly leading to erroneous adsorption equilibrium measurements. Therefore, the solenoid valves were substituted by manual ball valves. After the volumetric unit improvement its operation was validated. For this purpose, the adsorption equilibrium of carbon dioxide (CO2) at 323K and 0 - 20 bar was measured on two different activated carbon samples, in the of extrudates (ANG6) and of a honeycomb monolith (ACHM). The adsorption equilibrium results were compared with data previously measured by the research group, using a high-pressure microbalance from Rubotherm GmbH (Germany) – gravimetric. The results obtained using both apparatuses are coincident thus validating the good operation of the volumetric unit upgraded in this work. Furthermore, the adsorption equilibrium of CO2 at 303K and 0 - 10 bar on Metal-Organic Frameworks (MOFs) Cu-BTC and Fe-BTC was also studied. The CO2 adsorption equilibrium results for both MOFs were compared with the literature results showing good agreement, which confirms the good quality of the experimental results obtained in the new volumetric unit. Cu-BTC sample showed significantly higher CO2 adsorption capacity when compared with the Fe-BTC sample. The revamping of the volumetric unit included a new valve configuration in order to allow testing an alternative method for the measurement of adsorption equilibrium. This new method was employed to measure the adsorption equilibrium of CO2 on ANG6 and ACHM at 303, 323 and 353K within 0-10 bar. The good quality of the obtained experimental data was testified by comparison with data previously obtained by the research group in a gravimetric apparatus.

Molecular simulation of gas adsorption equilibria in nanoporous materials

This work is divided into two distinct parts. The first part consists of the study of the metal organic framework UiO-66Zr, where the aim was to determine the force field that best describes the adsorption equilibrium properties of two different gases, methane and carbon dioxide. The other part of the work focuses on the study of the single wall carbon nanotube topology for ethane adsorption; the aim was to simplify as much as possible the solid-fluid force field model to increase the computational efficiency of the Monte Carlo simulations. The choice of both adsorbents relies on their potential use in adsorption processes, such as the capture and storage of carbon dioxide, natural gas storage, separation of components of biogas, and olefin/paraffin separations. The adsorption studies on the two porous materials were performed by molecular simulation using the grand canonical Monte Carlo (μ,V,T) method, over the temperature range of 298-343 K and pressure range 0.06-70 bar. The calibration curves of pressure and density as a function of chemical potential and temperature for the three adsorbates under study, were obtained Monte Carlo simulation in the canonical ensemble (N,V,T); polynomial fit and interpolation of the obtained data allowed to determine the pressure and gas density at any chemical potential. The adsorption equilibria of methane and carbon dioxide in UiO-66Zr were simulated and compared with the experimental data obtained by Jasmina H. Cavka et al. The results show that the best force field for both gases is a chargeless united-atom force field based on the TraPPE model. Using this validated force field it was possible to estimate the isosteric heats of adsorption and the Henry constants. In the Grand-Canonical Monte Carlo simulations of carbon nanotubes, we conclude that the fastest type of run is obtained with a force field that approximates the nanotube as a smooth cylinder; this approximation gives execution times that are 1.6 times faster than the typical atomistic runs.

Aplicação de métodos estatísticos para o controlo e melhoria do processo: produção de rolhas técnicas de cortiça

A aposta na Qualidade e no Controlo de Processos, constitui actualmente, um requisito fundamental para as empresas se manterem competitivas. A Amorim e Irmãos, empresa onde o presente estudo é realizado, é líder de mercado no sector da cortiça, e aposta na melhoria contínua dos seus processos e produtos. Em linha com essa estratégia, a presente dissertação tem como objectivo melhorar o processo de produção de um dos produtos da Amorim e Irmãos, as rolhas de cortiça Twin-Top produzidas na unidade industrial Equipar, em Coruche. O processo em estudo, denominado de Rosa, é caracterizado por ter uma elevada variabilidade pois é muito sensível às condições da temperatura ambiente e à heterogeneidade da matéria prima. Os objectivos do processo passam precisamente por reduzir a heterogeneidade presente nas características da cortiça, ao definir valores alvo para a humidade, Massa volúmica corrigida a 8% de humidade e quantidade de um composto presente na cortiça, o TCA. Este composto afecta negativamente as características da rolha, portanto um dos objectivos deste trabalho é diminuir a quantidade de TCA presente no granulado. Por forma a solucionar o problema, de reduzir a variabilidade do Rosa aproximando-o dos valores alvo para as características a controlar aplicaram-se métodos estatísticos como o Desenho de Experiências e as Cartas de Controlo. O Rosa caracteriza-se por ter várias etapas, percorridas pelo granulado de forma sequencial. Tendo em conta que apenas na primeira etapa é que ocorrem alterações na quantidade de TCA presente no granulado decidiu-se que seria adequado realizar dois Desenhos de Experiências. O primeiro a ser aplicado na fase inicial do processo para maximizar a extracção de TCA e o segundo a ser aplicado nas restantes fases para controlar as outras características em cima referidas. Por fim realizou-se um estudo para aplicação de Cartas de Controlo no processo. Por via do primeiro DOE foram implementadas alterações no processo (aumento da pressão de vapor para 2,3 bar e da velocidade dos sem-fins para 10 Hz, na máquina RH), que permitiram reduzir com sucesso a quantidade média de TCA (2,4,6 tricloroanisol) presente no granulado. Este feito teve bastante relevância para a empresa, uma vez que a extracção deste composto constitui um dos seus objectivos estratégicos e é também uma das metas mais importantes a nível da qualidade do produto.(...)