A fuzzified systematic adjustment of the robotic Darwinian PSO

The Darwinian Particle Swarm Optimization (DPSO) is an evolutionary algorithm that extends the Particle Swarm Optimization using natural selection to enhance the ability to escape from sub-optimal solutions. An extension of the DPSO to multi-robot applications has been recently proposed and denoted as Robotic Darwinian PSO (RDPSO), benefiting from the dynamical partitioning of the whole population of robots, hence decreasing the amount of required information exchange among robots. This paper further extends the previously proposed algorithm adapting the behavior of robots based on a set of context-based evaluation metrics. Those metrics are then used as inputs of a fuzzy system so as to systematically adjust the RDPSO parameters (i.e., outputs of the fuzzy system), thus improving its convergence rate, susceptibility to obstacles and communication constraints. The adapted RDPSO is evaluated in groups of physical robots, being further explored using larger populations of simulated mobile robots within a larger scenario.

Standard commercial education robotic platform: intermediate solution to teaching robotics

Teaching robotics to students at the beginning of their studies has become a huge challenge. Simulation environments can be an effective solution to that challenge where students can interact with simulated robots and have the first contact with robotic constraints. From our previous experience with simulation environments it was possible to observe that students with lower background knowledge in robotics where able to deal with a limited number of constraints, implement a simulated robotic platform and study several sensors. The question is: after this first phase what should be the best approach? Should the student start developing their own hardware? Hardware development is a very important part of an engineer's education but it can also be a difficult phase that could lead to discouragement and loss of motivation in some students. Considering the previous constraints and first year engineering students’ high abandonment rate it is important to develop teaching strategies to deal with this problem in a feasible way. The solution that we propose is the integration of a low-cost standard robotic platform WowWee Rovio as an intermediate solution between the simulation phase and the stage where the students can develop their own robots. This approach will allow the students to keep working in robotic areas such as: cooperative behaviour, perception, navigation and data fusion. The propose approach proved to be a motivation step not only for the students but also for the teachers. Students and teachers were able to reach an agreement between the level of demand imposed by the teachers and satisfaction/motivation of the students.

Thermographic and visible spectrum camera calibration for marine robotic target detection

Oceans - San Diego, 2013

Kitchen robot prod. line development. Proj. of Bowden cables cutting and thermal forming machine.

This document presents particular description of work done during student’s internship in PR Metal company realized as ERASMUS PROJECT at ISEP. All information including company’s description and its structure, overview of the problems and analyzed cases, all stages of projects from concept to conclusion can be found here. Description of work done during the internship is divided here into two pieces. First part concerns one activities of the company which is robotic chefs (kitchen robot) production line. Work, that was done for development of this line involved several tasks, among them: creating a single-worker montage station for screwing robots housing’s parts, improve security system for laser welding chamber, what particularly consists in designing automatically closing door system with special surface, that protects against destructive action of laser beam, test station for examination of durability of heating connectors, solving problem with rotors vibrations. Second part tells about main task, realized in second half of internship and stands a complete description of machine development and design. The machine is a part of car handle latch cable production line and its tasks are: cutting cable to required length and hot-forming plastic cover for further assembly needs.

Application of fractional algorithms in the control of a robotic bird

In this paper, it is studied the dynamics of the robotic bird in terms of time response and robustness. It is analyzed the wing angle of attack and the velocity of the bird, the tail influence, the gliding flight and the flapping flight. The results are positive for the construction of flying robots. The development of computational simulation based on the dynamic of the robotic bird should allow testing strategies and different algorithms of control such as integer and fractional controllers.

A mobile robot platform for open learning based on serious games and remote laboratories

Within the pedagogical community, Serious Games have arisen as a viable alternative to traditional course-based learning materials. Until now, they have been based strictly on software solutions. Meanwhile, research into Remote Laboratories has shown that they are a viable, low-cost solution for experimentation in an engineering context, providing uninterrupted access, low-maintenance requirements, and a heightened sense of reality when compared to simulations. This paper will propose a solution where both approaches are combined to deliver a Remote Laboratory-based Serious Game for use in engineering and school education. The platform for this system is the WebLab-Deusto Framework, already well-tested within the remote laboratory context, and based on open standards. The laboratory allows users to control a mobile robot in a labyrinth environment and take part in an interactive game where they must locate and correctly answer several questions, the subject of which can be adapted to educators' needs. It also integrates the Google Blockly graphical programming language, allowing students to learn basic programming and logic principles without needing to understand complex syntax.

Autonomous bathymetry for risk assessment with ROAZ robotic surface vehicle

The use of unmanned marine robotic vehicles in bathymetric surveys is discussed. This paper presents recent results in autonomous bathymetric missions with the ROAZ autonomous surface vehicle. In particular, robotic surface vehicles such as ROAZ provide an efficient tool in risk assessment for shallow water environments and water land interface zones as the near surf zone in marine coast. ROAZ is an ocean capable catamaran for distinct oceanographic missions, and with the goal to fill the gap were other hydrographic surveys vehicles/systems are not compiled to operate, like very shallow water rivers and marine coastline surf zones. Therefore, the use of robotic systems for risk assessment is validated through several missions performed either in river scenario (in a very shallow water conditions) and in marine coastlines.

Decentralized Target Tracking based on Multi-Robot Cooperative Triangulation

Target tracking with bearing-only sensors is a challenging problem when the target moves dynamically in complex scenarios. Besides the partial observability of such sensors, they have limited field of views, occlusions can occur, etc. In those cases, cooperative approaches with multiple tracking robots are interesting, but the different sources of uncertain information need to be considered appropriately in order to achieve better estimates. Even though there exist probabilistic filters that can estimate the position of a target dealing with incertainties, bearing-only measurements bring usually additional problems with initialization and data association. In this paper, we propose a multi-robot triangulation method with a dynamic baseline that can triangulate bearing-only measurements in a probabilistic manner to produce 3D observations. This method is combined with a decentralized stochastic filter and used to tackle those initialization and data association issues. The approach is validated with simulations and field experiments where a team of aerial and ground robots with cameras track a dynamic target.

TIGRE - An autonomous ground robot for outdoor exploration

13th International Conference on Autonomous Robot Systems (Robotica), 2013

High-Accuracy Low-Cost RTK-GPS for an Unmanned Surface Vehicle

This work presents a low cost RTK-GPS system for localization of unmanned surface vehicles. The system is based on the use of standard low cost L1 band receivers and in the RTKlib open source software library. Mission scenarios with multiple robotic vehicles are addressed as the ones envisioned in the ICARUS search and rescue case where the possibility of having a moving RTK base on a large USV and multiple smaller vehicles acting as rovers in a local communication network allows for local relative localization with high quality. The approach is validated in operational conditions with results presented for moving base scenario. The system was implemented in the SWIFT USV with the ROAZ autonomous surface vehicle acting as a moving base. This setup allows for the performing of a missions in a wider range of environments and applications such as precise 3D environment modeling in contained areas and multiple robot operations.

Neural control of an autonomous robot

This article aims to apply the concepts associated with artificial neural networks (ANN) in the control of an autonomous robot system that is intended to be used in competitions of robots. The robot was tested in several arbitrary paths in order to verify its effectiveness. The results show that the robot performed the tasks with success. Moreover, in the case of arbitrary paths the ANN control outperforms other methodologies, such as fuzzy logic control (FLC).

Water jet based autonomous surface vehicle for coastal waters operations

This paper presents the design of low cost, small autonomous surface vehicle for missions in the coastal waters and specifically for the challenging surf zone. The main objective of the vehicle design described in this paper is to address both the capability of operation at sea in relative challenging conditions and maintain a very low set of operational requirements (ease of deployment). This vehicle provides a first step towards being able to perform general purpose missions (such as data gathering or patrolling) and to at least in a relatively short distances to be able to be used in rescue operations (with very low handling requirements) such as carrying support to humans on the water. The USV is based on a commercially available fiber glass hull, it uses a directional waterjet powered by an electrical brushless motor for propulsion, thus without any protruding propeller reducing danger in rescue operations. Its small dimensions (1.5 m length) and weight allow versatility and ease of deployment. The vehicle design is described in this paper both from a hardware and software point of view. A characterization of the vehicle in terms of energy consumption and performance is provided both from test tank and operational scenario tests. An example application in search and rescue is also presented and discussed with the integration of this vehicle in the European ICARUS (7th framework) research project addressing the development and integration of robotic tools for large scale search and rescue operations.

Development of advanced human robot interaction systems

O trabalho aqui apresentado é a Dissertação da minha Tese do curso de Mestrado em Engenharia Eletrotécnica e de Computadores do ISEP, realizada em parceria com o INESC TEC. O trabalho consiste no desenvolvimento de um sistema avançado de interação entre homem-robô, usando ferramentas de software livres e de domínio público e hardware pouco dispendioso e facilmente acessível. Pretende-se que o sistema desenvolvido possa ser adotado por pequenas ou micro empresas, daí a restrição monetária. Este tipo de empresas tem, por norma, uma capacidade de investimento pequena, e ficam impossibilitadas de aceder a este tipo de sistemas automatizados se estes forem caros. No entanto, o robô continua a ser um componente fundamental, sendo dispendioso. Os trabalhos realizados pelos sistemas robóticos podem por um lado, ser repetitivos sem necessidade de grandes ajustes; por outro lado, o trabalho a realizar pode ser bastante diverso, sendo necessários bastantes ajustes com (possivelmente) programação do robô. As empresas podem não ter disponível mão-de-obra qualificada para realização da programação do robô. Pretende-se então um sistema de “ensino” que seja simples e rápido. Este trabalho pretende satisfazer as necessidades de um sistema de interação homem-robô intuitivo mesmo para operadores que não estejam familiarizados com a robótica. Para simplificar a transferência de informação da tarefa a desempenhar pelo sistema robótico é usado um sistema de infravermelhos para delinear a operação a desempenhar, neste caso concreto uma operação de soldadura. O operador usa um apontador com marcadores, a posição destes marcadores é detetada usando duas câmaras para permitir o posicionamento tridimensional no espaço. As câmaras possuem filtros infravermelhos para separar o espectro de luz. Para o controlo do sistema e interface com o robô é usado um computador de baixos recursos computacionais e energéticos, e também de baixo custo. O sistema desenvolvido é portanto computacionalmente leve para poder ser executado neste computador.

Melhoria e automação de linhas de montagem

Hoje em dia, e com os avanços tecnológicos a surgirem de forma constante, existem novas áreas que têm de ser consideradas com um foco importante por parte de todas as organizações, sendo uma delas a robótica industrial. Motivada em aumentar o seu output, as condições de trabalho para os seus colaboradores, bem como todas as condições de organização da logística interna, a Grohe Portugal, mais especificamente o departamento da montagem, achou relevante fazer um estudo de métodos e tempos, calculando os ganhos potenciais de aumento de output com introdução de robótica nas linhas dos cartuchos. Os objetivos principais seriam então, fazer uma restruturação de todo o layout dessas linhas, tendo como foco automatizar alguma(s) operação(ões), conseguindo assim uma melhoria significativa do output dessas linhas com o menor payback possível. Posto isto, esta dissertação pretende apresentar o trabalho desenvolvido junto da Grohe Portugal, que teve como objetivo fazer os estudos e a automatização de linhas de montagem de cartuchos, bem como melhorar algumas linhas de montagem tendo em conta fatores ergonómicos. Relativamente à automatização da linha dos cartuchos, foi importante estudar todos os seguintes aspetos:  utilização de unidades robóticas;  ergonomia;  ganhos de produtividade;  automatizar ou semi-automatizar operações;  simplificar processos de montagem;  simplificar setups;  solicitar orçamentos;  elaborar caderno de encargos. Para a realização deste projeto, o trabalho desenvolvido foi decomposto em várias etapas, entre as quais se destacam:  análise e estudo dos métodos e sequências de montagem;  levantamento de todos os componentes e operações de montagem até à obtenção do cartucho final;  estudo de tempos de todas essas operações de montagem;  caraterização de um novo layout para as linhas com a introdução de unidades robóticas, tanto quanto possível, mais adequadas;  elaboração de caderno de encargos para ser enviado a empresas, para estas poderem apresentar uma orçamentação, bem como indicar as unidades robóticas mais adequadas para as tarefas pretendidas;  automatização da linha dos cartuchos. Relativamente ao projeto de novas linhas de montagem tendo em conta fatores ergonómicos, de forma a melhorar os sistemas de abastecimento e as condições de trabalho por parte dos operadores, foram postos em prática diferentes passos, nomeadamente:  identificação de todos os processos de montagem realizados pelos operadores na linha a melhorar;  estudo e definição da disposição dos componentes na nova linha, bem como a sua forma de abastecimento;  projeto da nova linha de montagem em 3D com recurso ao software SolidWorks;  realização prática da linha, acompanhando e ajudando a equipa da ferramentaria. O balanço final do trabalho foi bastante positivo, tanto na automatização das linhas de montagem dos cartuchos, em que todo o seu estudo foi alcançado com sucesso, como no melhoramento ergonómico das linhas de montagem, tendo-se alcançado melhorias em alguns índices de qualidade, tempos de abastecimento, organização das linhas, e nas condições de iluminação, resultando essas melhorias numa avaliação positiva por parte dos colaboradores que nelas trabalham todos os dias.