PPO Reaction Scale-up

O óxido de polifenileno com a marca comercial PPO® é uma das resinas principais produzidas na SABIC IP e o ingrediente principal do plástico de engenharia com a marca registada, Noryl®. A equipa de tecnologia de processo de PPO® desenvolve uma série de novos produtos em reactores de pequena escala, tanto em Selkirk como em Bergen op Zoom. Para se efectuar uma transição rápida da escala laboratorial para a fábrica, é necessário um conhecimento completo do reactor. O objectivo deste projecto consiste em esboçar linhas gerais para o scale-up de novos produtos de PPO1, do laboratório para a escala industrial, baseado no estudo de um tipo de PPO, PPO 803. Este estudo pode ser dividido em duas fases. Numa primeira fase, as receitas e os perfis da reacção são comparados, de onde se retiram as primeiras conclusões. Posteriormente, com base nestas conclusões, é realizado um planeamento experimental. O estudo inicial sugeriu que a receita, a temperatura inicial do reactor e a velocidade do agitador poderiam influenciar o tempo da reacção bem como a queda da velocidade intrínseca do polímero (IV drop). As reacções experimentais mostraram que a receita é o principal factor que influencia, tanto o tempo de reacção, como a queda de viscosidade intrínseca. O tempo de reacção será tanto maior quanto menor a agitação devido à má dispersão do oxigénio na mistura. O uso de temperaturas iniciais elevadas conduz a uma queda maior da viscosidade intrínseca devido à desactivação do catalisador. O método experimental utilizado no laboratório de Bergen op Zoom é um bom exemplo, simulador, do procedimento utilizado na fábrica.

Residential energy resources management by a SCADA system in case of excess wind generation

The end consumers in a smart grid context are seen as active players. The distributed generation resources applied in smart home system as a micro and small-scale systems can be wind generation, photovoltaic and combine heat and power facility. The paper addresses the management of domestic consumer resources, i.e. wind generation, solar photovoltaic, combined heat and power, electric vehicle with gridable capability and loads, in a SCADA system with intelligent methodology to support the user decision in real time. The main goal is to obtain the better management of excess wind generation that may arise in consumer’s distributed generation resources. The optimization methodology is performed in a SCADA House Intelligent Management context and the results are analyzed to validate the SCADA system.

Renewable-based generation integration in electricity markets with virtual power producers

The development of renewable energy sources and Distributed Generation (DG) of electricity is of main importance in the way towards a sustainable development. However, the management, in large scale, of these technologies is complicated because of the intermittency of primary resources (wind, sunshine, etc.) and small scale of some plants. The aggregation of DG plants gives place to a new concept: the Virtual Power Producer (VPP). VPPs can reinforce the importance of these generation technologies making them valuable in electricity markets. VPPs can ensure a secure, environmentally friendly generation and optimal management of heat, electricity and cold as well as optimal operation and maintenance of electrical equipment, including the sale of electricity in the energy market. For attaining these goals, there are important issues to deal with, such as reserve management strategies, strategies for bids formulation, the producers’ remuneration, and the producers’ characterization for coalition formation. This chapter presents the most important concepts related with renewable-based generation integration in electricity markets, using VPP paradigm. The presented case studies make use of two main computer applications:ViProd and MASCEM. ViProd simulates VPP operation, including the management of plants in operation. MASCEM is a multi-agent based electricity market simulator that supports the inclusion of VPPs in the players set.

Technical and economic resources management in smart grids using heuristic optimization methods

Intensive use of Distributed Generation (DG) represents a change in the paradigm of power systems operation making small-scale energy generation and storage decision making relevant for the whole system. This paradigm led to the concept of smart grid for which an efficient management, both in technical and economic terms, should be assured. This paper presents a new approach to solve the economic dispatch in smart grids. The proposed methodology for resource management involves two stages. The first one considers fuzzy set theory to define the natural resources range forecast as well as the load forecast. The second stage uses heuristic optimization to determine the economic dispatch considering the generation forecast, storage management and demand response

A probabilistic methodology for distributed generation location in isolated electrical service area

Distributed generation unlike centralized electrical generation aims to generate electrical energy on small scale as near as possible to load centers, interchanging electric power with the network. This work presents a probabilistic methodology conceived to assist the electric system planning engineers in the selection of the distributed generation location, taking into account the hourly load changes or the daily load cycle. The hourly load centers, for each of the different hourly load scenarios, are calculated deterministically. These location points, properly weighted according to their load magnitude, are used to calculate the best fit probability distribution. This distribution is used to determine the maximum likelihood perimeter of the area where each source distributed generation point should preferably be located by the planning engineers. This takes into account, for example, the availability and the cost of the land lots, which are factors of special relevance in urban areas, as well as several obstacles important for the final selection of the candidates of the distributed generation points. The proposed methodology has been applied to a real case, assuming three different bivariate probability distributions: the Gaussian distribution, a bivariate version of Freund’s exponential distribution and the Weibull probability distribution. The methodology algorithm has been programmed in MATLAB. Results are presented and discussed for the application of the methodology to a realistic case and demonstrate the ability of the proposed methodology for efficiently handling the determination of the best location of the distributed generation and their corresponding distribution networks.

Concepção e instalação de tabelas multifunções para recintos desportivos cobertos

Mestrado em Engenharia Electrotécnica – Sistemas Eléctricos de Energia

Reliable real-time communication in CAN networks

Controller area network (CAN) is a fieldbus network suitable for small-scale distributed computer controlled systems (DCCS), being appropriate for sending and receiving short real-time messages at speeds up to 1 Mbit/sec. Several studies are available on how to guarantee the real-time requirements of CAN messages, providing preruntime schedulability conditions to guarantee the real-time communication requirements of DCCS traffic. Usually, it is considered that CAN guarantees atomic multicast properties by means of its extensive error detection/signaling mechanisms. However, there are some error situations where messages can be delivered in duplicate or delivered only by a subset of the receivers, leading to inconsistencies in the supported applications. In order to prevent such inconsistencies, a middleware for reliable communication in CAN is proposed, taking advantage of CAN synchronous properties to minimize the runtime overhead. Such middleware comprises a set of atomic multicast and consolidation protocols, upon which the reliable communication properties are guaranteed. The related timing analysis demonstrates that, in spite of the extra stack of protocols, the real-time properties of CAN are preserved since the predictability of message transfer is guaranteed.

Integrating inaccessibility in response time analysis of CAN networks

Controller Area Network (CAN) is a fieldbus network suitable for small-scale Distributed Computer Controlled Systems, being appropriate for transferring short real-time messages. Nevertheless, it must be understood that the continuity of service is not fully guaranteed, since it may be disturbed by temporary periods of network inaccessibility [1]. In this paper, such temporary periods of network inaccessibility are integrated in the response time analysis of CAN networks. The achieved results emphasise that, in the presence of temporary periods of network inaccessibility, a CAN network is not able to provide different integrity levels to the supported applications, since errors in low priority messages interfere with the response time of higher priority message streams.

Programming atomic multicasts in CAN

In Distributed Computer-Controlled Systems (DCCS), a special emphasis must be given to the communication infrastructure, which must provide timely and reliable communication services. CAN networks are usually suitable to support small-scale DCCS. However, they are known to present some reliability problems, which can lead to an unreliable behaviour of the supported applications. In this paper, an atomic multicast protocol for CAN networks is proposed. This protocol explores the CAN synchronous properties, providing a timely and reliable service to the supported applications. The implementation of such protocol in Ada, on top of the Ada version of Real-Time Linux is presented, which is used to demonstrate the advantages and disadvantages of the platform to support reliable communications in DCCS.

Perspectives of the Internal Public in a Cultural Event: the Case of Noc Noc, Guimarães - Portugal

Given the significant impact that cultural events may have in local communities and the inherent organization complexity, it is important to understand their specificities. Most of the times cultural events disregard marketing and often marketing is distant from art. Thus an analysis of an inside perspective might bring significant returns to the organization of such an event. This paper considers the three editions (2011, 2012 and 2013) of a cultural event – Noc Noc – organized by a local association in the city of Guimarães, Portugal. Its format is based in analogous events, as Noc Noc intends to convert everyday spaces (homes, commercial outlets and a number of other buildings) into cultural spaces, processed and transformed by artists, hosts and audiences. By interviewing a sample of people (20) who have hosted this cultural event, sometimes doubling as artists, and by experiencing the three editions of the event, this paper illustrates how the internal public understands this particular cultural event, analyzing specifically their motivations, ways of acting and participating, as well as their relationship with the public, with the organization of the event and with art in general. Results support that artists and hosts motivations must be identified in a timely and appropriate moment, as well as their views of this particular cultural event, in order to keep them participating, since low budget cultural events such as this one may have a key role in small scale cities.

Dispatch of distributed Energy Resources to Provide Energy and Reserve in Smart Grids using a Particle Swarm Optimization Approach

The smart grid concept is a key issue in the future power systems, namely at the distribution level, with deep concerns in the operation and planning of these systems. Several advantages and benefits for both technical and economic operation of the power system and of the electricity markets are recognized. The increasing integration of demand response and distributed generation resources, all of them mostly with small scale distributed characteristics, leads to the need of aggregating entities such as Virtual Power Players. The operation business models become more complex in the context of smart grid operation. Computational intelligence methods can be used to give a suitable solution for the resources scheduling problem considering the time constraints. This paper proposes a methodology for a joint dispatch of demand response and distributed generation to provide energy and reserve by a virtual power player that operates a distribution network. The optimal schedule minimizes the operation costs and it is obtained using a particle swarm optimization approach, which is compared with a deterministic approach used as reference methodology. The proposed method is applied to a 33-bus distribution network with 32 medium voltage consumers and 66 distributed generation units.

Experimental Reinforcement of Wood Beams

Rehabilitation is becoming more and more usual in the construction sector in Portugal. The introduction of newer construction materials and technical know-how of integrating different materials for achieving desired engineering goals is an important step to the development of the sector. Wood industry is also getting more and more adapted to composite technologies with the introduction of the so called “highly engineered wood products” and with the use of modification treatments. This work is an attempt to explain the viability of using stainless steel and glass fibre reinforced polymer (GFRP) as reinforcements in wood beams. This thesis specifically focuses on the flexural behaviour of Portuguese Pine unmodified and modified wood beams. Two types of modification were used: 1,3-dimethylol-4,5- dihydroxyethyleneurea (DMDHEU) resin and amid wax. The behaviour of the material was analysed with a nonlinear model. The latter model simulates the behaviour of the reinforced wood beams under flexural loading. Small-scale beams (1:15) were experimented in flexural bending and the experimental results obtained were compared with the analytical model results. The experiments confirm the viability of the reinforcing schemes and the working procedures. Experimental results showed fair agreement with the nonlinear model. A strength increase between 15% and 80% was achieved. Stiffness increased by 40% to 50% in beams reinforced with steel but no significant increase was achieved with the glass fibre reinforcement.

Desenvolvimento de programação offline e de novos processos robotizados de lixamento

Atualmente a vantagem competitiva de uma empresa passa pela sua rápida adaptação às variações de procura do mercado, sendo necessário garantir elevados níveis de produtividade e, simultaneamente, grande flexibilidade, indispensável ao fabrico de pequenos lotes. A necessidade de ajuste do processo e a diminuição da média de vida do produto levam a paragens cada vez mais frequentes da célula de fabrico para programação e afinação, com consequentes perdas de produtividade. De forma a dar resposta a estes problemas, neste trabalho é testada a viabilidade da utilização da programação e simulação offline de tarefas de lixamento na Grohe Portugal, complementando a solução com o desenvolvimento de um novo método de afinação do programa, permitindo uma adaptação às flutuações do processo produtivo. Para isso foi necessário analisar o estado da arte dos robôs industriais na área de acabamento superficial e respetivos métodos de programação. Em seguida, após um trabalho prévio rigoroso de preparação e modelação da célula de trabalho, é possível fazer a programação offline das várias rotinas e trajetórias complexas que compõem um ciclo de lixamento de um produto, contribuindo para o aumento da qualidade do produto final sem comprometer os níveis de produtividade. Nesta dissertação são descritos e detalhados alguns dos procedimentos fulcrais no sucesso da aplicação deste método de programação. Por último é feita uma nova abordagem ao método de ajuste ponto-a-ponto convencional, desenvolvendo-se para isso um sistema de ajuste automático do programa, dotando o robô da capacidade de se adaptar às variações do processo, assegurando a consistência do mesmo. Foram realizados testes em pequena escala, extrapolando-se os resultados para a aplicação deste novo método no processo produtivo da Grohe Portugal, como forma de complemento ao método convencional de ajuste ponto-a-ponto do programa, reduzindo o tempo de paragem da célula de trabalho.