3 resultados para in-situ test
em Instituto Politécnico do Porto, Portugal
Resumo:
Naturally occurring radioactive materials (NORM) under certain conditions can reach hazardous radiological levels contributing to an additional exposure dose to ionizing radiation. Most environmental concerns are associated with uranium mining and milling sites, but the same concerns should be addressed to natural near surface occurrences of uranium as well as man-made sources such as technologically enhanced naturally occurring radioactive materials (TENORM) resulting from phosphates industry, ceramic industry and energy production activities, in particular from coal-fired power plants which is one of the major sources of increased exposure to man from enhanced naturally occurring materials. This work describes the methodology developed to assess the environmental radiation by in situ gamma spectrometry in the vicinity of a Portuguese coal fired power plant. The current investigation is part of a research project that is undergoing in the vicinity of Sines Coal-Fired Power Plant (south of Portugal) until the end of 2013.
Resumo:
Using low cost portable devices that enable a single analytical step for screening environmental contaminants is today a demanding issue. This concept is here tried out by recycling screen-printed electrodes that were to be disposed of and by choosing as sensory element a low cost material offering specific response for an environmental contaminant. Microcystins (MCs) were used as target analyte, for being dangerous toxins produced by cyanobacteria released into water bodies. The sensory element was a plastic antibody designed by surface imprinting with carefully selected monomers to ensure a specific response. These were designed on the wall of carbon nanotubes, taking advantage of their exceptional electrical properties. The stereochemical ability of the sensory material to detect MCs was checked by preparing blank materials where the imprinting stage was made without the template molecule. The novel sensory material for MCs was introduced in a polymeric matrix and evaluated against potentiometric measurements. Nernstian response was observed from 7.24 × 10−10 to 1.28 × 10−9 M in buffer solution (10 mM HEPES, 150 mM NaCl, pH 6.6), with average slopes of −62 mVdecade−1 and detection capabilities below 1 nM. The blank materials were unable to provide a linear response against log(concentration), showing only a slight potential change towards more positive potentials with increasing concentrations (while that ofthe plastic antibodies moved to more negative values), with a maximum rate of +33 mVdecade−1. The sensors presented good selectivity towards sulphate, iron and ammonium ions, and also chloroform and tetrachloroethylene (TCE) and fast response (<20 s). This concept was successfully tested on the analysis of spiked environmental water samples. The sensors were further applied onto recycled chips, comprehending one site for the reference electrode and two sites for different selective membranes, in a biparametric approach for “in situ” analysis.
Resumo:
A conjuntura económica da construção não se encontra numa fase de prosperidade, existindo a necessidade de criar soluções construtivas que permitam a redução de custos dos materiais a nível de obra. As lajes de betão armado, devido à sua grande área de implantação, possuem uma parcela importante no orçamento final de qualquer obra de edifícios correntes. Sabendo das possibilidades de aligeiramento de lajes, torna-se necessária a realização de um estudo pormenorizado e comparativo entre soluções de aligeiramento. O desenvolvimento deste relatório reflete todo o trabalho efetuado durante a realização de um estágio curricular desenvolvido na empresa FercaNorte – Estruturas, Lajes e Cofragens, Lda. e foca-se num dimensionamento e estudo comparativo de soluções de lajes fungiformes aligeiradas, aplicadas a dois casos de estudo e também num dimensionamento e estudo comparativo de soluções de lajes aligeiradas unidirecionais mas apenas aplicadas a um caso de estudo. No primeiro caso de estudo, laje fungiforme com um vão de 6 metros nas duas direções, são dimensionadas e comparadas quatro soluções: laje fungiforme maciça; laje fungiforme aligeirada com blocos elipsoides perdidos dispostos de forma ortogonal e envolvidos totalmente por betão; laje fungiforme aligeirada com blocos elipsoides perdidos dispostos em formato de favo de mel e envolvidos totalmente por betão; e laje fungiforme nervurada com moldes recuperáveis. No segundo caso de estudo, laje fungiforme com um vão de 7,04 metros nas duas direções, são dimensionadas e comparadas cinco soluções: laje fungiforme maciça, laje fungiforme aligeirada com blocos cúbicos perdidos dispostos de forma ortogonal e envolvidos totalmente por betão; laje fungiforme aligeirada, com blocos elipsoides perdidos dispostos de forma ortogonal e envolvidos totalmente por betão; laje fungiforme aligeirada com blocos elipsoides perdidos dispostos em formato de favo de mel e envolvidos totalmente por betão; e laje fungiforme nervurada com moldes recuperáveis. No terceiro caso de estudo, laje unidirecional com um vão de 8 metros apoiada em vigas com vão de 5 metros, são dimensionadas e comparadas três soluções: laje maciça; laje aligeirada com perfis tubulares com secção transversal reta oval; e laje nervurada com moldes recuperáveis. No final é apresentada uma estimativa orçamental para cada solução analisada nos três casos de estudo abordados.