Preemption delay analysis for floating non-preemptive region scheduling

In real-time systems, there are two distinct trends for scheduling task sets on unicore systems: non-preemptive and preemptive scheduling. Non-preemptive scheduling is obviously not subject to any preemption delay but its schedulability may be quite poor, whereas fully preemptive scheduling is subject to preemption delay, but benefits from a higher flexibility in the scheduling decisions. The time-delay involved by task preemptions is a major source of pessimism in the analysis of the task Worst-Case Execution Time (WCET) in real-time systems. Preemptive scheduling policies including non-preemptive regions are a hybrid solution between non-preemptive and fully preemptive scheduling paradigms, which enables to conjugate both world's benefits. In this paper, we exploit the connection between the progression of a task in its operations, and the knowledge of the preemption delays as a function of its progression. The pessimism in the preemption delay estimation is then reduced in comparison to state of the art methods, due to the increase in information available in the analysis.

An improved preemption delay upper bound for floating non-preemptive region

In embedded systems, the timing behaviour of the control mechanisms are sometimes of critical importance for the operational safety. These high criticality systems require strict compliance with the offline predicted task execution time. The execution of a task when subject to preemption may vary significantly in comparison to its non-preemptive execution. Hence, when preemptive scheduling is required to operate the workload, preemption delay estimation is of paramount importance. In this paper a preemption delay estimation method for floating non-preemptive scheduling policies is presented. This work builds on [1], extending the model and optimising it considerably. The preemption delay function is subject to a major tightness improvement, considering the WCET analysis context. Moreover more information is provided as well in the form of an extrinsic cache misses function, which enables the method to provide a solution in situations where the non-preemptive regions sizes are small. Finally experimental results from the implementation of the proposed solutions in Heptane are provided for real benchmarks which validate the significance of this work.

Job phasing aware preemption deferral

Preemptions account for a non-negligible overhead during system execution. There has been substantial amount of research on estimating the delay incurred due to the loss of working sets in the processor state (caches, registers, TLBs) and some on avoiding preemptions, or limiting the preemption cost. We present an algorithm to reduce preemptions by further delaying the start of execution of high priority tasks in fixed priority scheduling. Our approaches take advantage of the floating non-preemptive regions model and exploit the fact that, during the schedule, the relative task phasing will differ from the worst-case scenario in terms of admissible preemption deferral. Furthermore, approximations to reduce the complexity of the proposed approach are presented. Substantial set of experiments demonstrate that the approach and approximations improve over existing work, in particular for the case of high utilisation systems, where savings of up to 22% on the number of preemption are attained.

Aplicação da metodologia SMED numa linha de envernizamento/pintura de revestimentos de cortiça

O presente trabalho visa a redução do tempo de mudança de produção e consequente aumento de produtividade de uma linha de envernizamento/pintura integrada na empresa Amorim Revestimentos SA, unidade S. Paio de Oleiros, que se dedica à produção de pisos flutuantes. Esta necessidade surgiu pelo facto desta linha de produção ser um ponto de estrangulamento do processo produtivo no departamento em que está inserida, devido principalmente à diminuição do tamanho de lotes e aumento da variedade de artigos a produzir. O trabalho envolveu as várias etapas da ferramenta SMED às quais está inerente a aplicação da técnica 5S às máquinas e ferramentas garantindo, assim, o posto de trabalho arrumado, limpo, seguro e com tudo pronto a ser utilizado. Aplicou-se a ferramenta SMED a dois tipos de mudança de acabamento e à mudança de rolo de pintura. Após a implementação desta ferramenta verificou-se uma redução de tempos de 37% (48 para 30 minutos) na mudança de pintura e acabamento de verniz, reduziu-se 25% (32 para 24 minutos) na mudança só de pintura e 13% (46 para 40 minutos) na mudança de rolo de pintura. Estes resultados foram alcançados através da redução do tempo das tarefas externas e internas e transformação das tarefas internas em externas consequentes da aplicação de um conjunto de ações de melhorias. Também foi fundamental a alteração do método de trabalho e a organização geral do posto de trabalho, no que diz respeito à repartição equilibrada das tarefas pelos dois operadores, alteração do sequenciamento das tarefas e aplicação da técnica 5S. As soluções encontradas estão sendo monitorizadas através do registo efectuado pelos operadores e realização de auditorias internas para garantir a perpetuação dos resultados.

Desenvolvimento de um robô com pernas inspirado no Alfaiate

A elaboração deste trabalho surge no âmbito da unidade curricular de Tese/Dissertação, integrada no Mestrado em Engenharia Eletrotécnica e de Computadores do Instituto Superior de Engenharia do Porto. O trabalho enquadra-se no âmbito da robótica de inspiração biológica, mais concretamente no desenvolvimento de um robô que apresente caraterísticas de locomoção similares ao inseto Alfaiate, modificando para este efeito um robô hexápode já existente. Inicialmente efetuou-se um estudo sobre a biologia do Alfaiate e dos vários tipos de padrões de locomoção adotados pelos animais. De seguida foi realizado um estudo sobre alguns robôs já existentes inspirados neste inseto. Após a realização desta fase de estudo, foram implementadas modificações ao robô hexápode, de forma a este conseguir apoiar-se e movimentar-se sobre a superfície da água. Para tal foram utilizados apoios em esferovite para as pernas, servomotores para a atuação e um sensor de IRPD para orientar o robô na sua trajetória. Em termos de controlo da estabilidade do corpo utilizou-se um giroscópio para permitir ao robô manter o seu corpo horizontal durante a locomoção em águas agitadas. Este trabalho termina com a realização de testes a diferentes padrões de locomoção, de forma a validar o que apresenta a melhor resposta em termos de velocidade.

Design and Implementation of a Biologically Inspired Swimming Robot - An EPS@ISEP 2014 Spring Project

This paper presents the development of a fish-like robot called Bro-Fish. Bro-Fish aims to be an educational toy dedicated to teaching mechanics, programming and the physics of floating objects to youngsters. The underlying intention is to awaken the interest of children for technology, especially biomimetic (biologically inspired) approaches, in order to promote sustainability and raise the level of ecological awareness. The main focus of this project was to create a robot with carangiform locomotion and controllable swimming, providing the opportunity to customize parts and experiment with the physics of floating objects. Therefore, the locomotion principles of fishes and mechanisms developed in related projects were analysed. Inspired by this background knowledge, a prototype was designed and implemented. The main achievement is the new tail mechanism that propels the robot. The tail resembles the undulation motion of fish bodies and is actuated in an innovative way, triggered by an elegant movement of a rotating helicoidal. First experimental tests revealed the potential of the proposed methodology to effectively generate forward propulsion.

Development of Biomimetic Robots in the EPS Engineering Programme Capstone Project

This paper presents the development of a fish-like robot called Bro-Fish. Bro-Fish aims to be an educational toy dedicated to teaching mechanics, programming and the physics of floating objects to youngsters. The underlying intention is to awaken the interest of children for technology, especially biomimetic (biologically inspired) approaches, in order to promote sustainability and raise the level of ecological awareness. The main focus of this project was to create a robot with carangiform locomotion and controllable swimming, providing the opportunity to customize parts and experiment with the physics of floating objects. Therefore, the locomotion principles of fishes and mechanisms developed in related projects were analysed. Inspired by this background knowledge, a prototype was designed and implemented. The main achievement is the new tail mechanism that propels the robot. The tail resembles the undulation motion of fish bodies and is actuated in an innovative way, triggered by an elegant movement of a rotating helicoidal. First experimental tests revealed the potential of the proposed methodology to effectively generate forward propulsion.