Ecotoxicity tests using the green algae chlorella vulgaris — a useful tool in hazardous effluents management

The treatment efficiency of laboratory wastewaters was evaluated and ecotoxicity tests with Chlorella vulgaris were performed on them to assess the safety of their environmental discharge. For chemical oxygen demand wastewaters, chromium (VI), mercury (II) and silver were efficiently removedby chemical treatments.Areduction of ecotoxicitywas achieved; nevertheless, an EC50 (effective concentration that causes a 50% inhibition in the algae growth) of 1.5% (v/v) indicated still high level of ecotoxicity. For chloride determination wastewaters, an efficient reduction of chromium and silver was achieved after treatment. Regarding the reduction of ecotoxicity observed, EC50 increased from 0.059% to 0.5%, only a 0.02% concentration in the aquatic environment would guarantee no effects. Wastewaters containing phenanthroline/iron (II) complex were treated by chemical oxidation. Treatmentwas satisfactory concerning chemical parameters, although an increase in ecotoxicitywas observed (EC50 reduced from 0.31% to 0.21%). The wastes from the kinetic study of persulphate and iodide reaction were treated with sodium bisulphite until colour was removed. Although they did not reveal significant ecotoxicity, only over 1% of the untreated waste produced observable effects over algae. Therefore, ecotoxicity tests could be considered a useful tool not only in laboratory effluents treatment, as shown, but also in hazardous wastewaters management.

Role of abrasive material on micro-abrasion wear tests

Micro-abrasion wear tests with ball-cratering configuration are widely used. Sources of variability are already studied by different authors and conditions for testing are parameterized by BS EN 1071-6: 2007 standard which refers silicon carbide as abrasive. However, the use of other abrasives is possible and allowed. In this work, ball-cratering wear tests were performed using four different abrasive particles of three dissimilar materials: diamond, alumina and silicon carbide. Tests were carried out under the same conditions on a steel plate provided with TiB2 hard coating. For each abrasive, five different test durations were used allowing understanding the initial wear phenomena. Composition and shape of abrasive particles were investigated by SEM and EDS. Scar areas were observed by optical and electronic microscopy in order to understand the wear effects caused by each of them. Scar geometry and grooves were analyzed and compared. Wear coefficient was calculated for each situation. It was observed that diamond particles produce well-defined and circular wear scars. Different silicon carbide particles presented dissimilar results as consequence of distinct particle shape and size distribution.

Influence of the abrasive particles size in the micro-abrasion wear tests of TiAlSiN thin coatings

Ball rotating micro-abrasion tribometers are commonly used to carry out wear tests on thin hard coatings. In these tests, different kinds of abrasives were used, as alumina (Al2O3), silicon carbide (SiC) or diamond. In each kind of abrasive, several particle sizes can be used. Some studies were developed in order to evaluate the influence of the abrasive particle shape in the micro-abrasion process. Nevertheless, the particle size was not well correlated with the material removed amount and wear mechanisms. In this work, slurry of SiC abrasive in distilled water was used, with three different particles size. Initial surface topography was accessed by atomic force microscopy (AFM). Coating hardness measurements were performed with a micro-hardness tester. In order to evaluate the wear behaviour, a TiAlSiN thin hard film was used. The micro-abrasion tests were carried out with some different durations. The abrasive effect of the SiC particles was observed by scanning electron microscopy (SEM) both in the films (hard material) as in the substrate (soft material), after coating perforation. Wear grooves and removed material rate were compared and discussed.

Efficient schedulability tests for real-time embedded systems with urgent routines

Task scheduling is one of the key mechanisms to ensure timeliness in embedded real-time systems. Such systems have often the need to execute not only application tasks but also some urgent routines (e.g. error-detection actions, consistency checkers, interrupt handlers) with minimum latency. Although fixed-priority schedulers such as Rate-Monotonic (RM) are in line with this need, they usually make a low processor utilization available to the system. Moreover, this availability usually decreases with the number of considered tasks. If dynamic-priority schedulers such as Earliest Deadline First (EDF) are applied instead, high system utilization can be guaranteed but the minimum latency for executing urgent routines may not be ensured. In this paper we describe a scheduling model according to which urgent routines are executed at the highest priority level and all other system tasks are scheduled by EDF. We show that the guaranteed processor utilization for the assumed scheduling model is at least as high as the one provided by RM for two tasks, namely 2(2√−1). Seven polynomial time tests for checking the system timeliness are derived and proved correct. The proposed tests are compared against each other and to an exact but exponential running time test.

Implementação de um processo industrial de coloração de granito

O presente estágio foi desenvolvido na Britafiel. Um dos projectos em que a Empresa se encontra envolvida é o STOCO, pretendendo implementar à escala industrial um processo de coloração de pedra granítica natural para fins decorativos. Foi neste projecto que se enquadrou o estágio. O tema do estágio centra-se no processo de coloração de granito tendo como principal foco a implementação de um processo industrial de produção de granito colorido. O projecto STOCO nasce da necessidade de complementar a actividade da empresa com produtos de maior valor acrescentado para valorização da matéria-prima de base, o granito. STOCO, resultante de Stone Color, é o nome dado ao projecto e ao novo produto que é granito colorido, sob a forma de brita. Pretende-se obter um produto amigo do ambiente e com boas características: manter a textura natural da pedra granítica e assegurar uma boa resistência a factores agressivos. Estudos prévios de qualidade e de toxicidade mostraram que o produto STOCO desenvolvido até então apresenta um bom comportamento face a agressões climatéricas e que não compromete a vida das espécies usadas nos testes (peixes). Em relação aos lixiviados e resíduos da pedra colorida STOCO, estes não apresentaram qualquer problema ambiental, sendo considerado um produto amigo do ambiente. À data de início do presente trabalho estava em funcionamento um equipamento protótipo de produção de granito colorido (100 kg/partida), sendo a instalação e o arranque da unidade industrial (3 ton/h) concretizados no início de 2014, já no decorrer deste trabalho. Os objectivos cumpridos no âmbito deste trabalho foram então a implementação de uma linha industrial de produção de brita colorida, avaliação técnica do processo e do custo industrial de produção associado às matérias-primas. Neste relatório é descrito o processo inicial adoptado e apresentam-se as alterações efectuadas para melhoria do processo produtivo. Resolveram-se problemas como: definição e instalação de equipamentos complementares para a entrada e a saída da brita no equipamento industrial; pó excessivo na brita; cheiro intenso a gás e elevado ruído; adequação do sistema de pintura; e secagem incompleta da brita. Alguns destes problemas não foram totalmente resolvidos, mas sim minimizados. O equipamento industrial necessita ainda de alterações em diversas áreas, que foram identificadas e para as quais são feitas sugestões de melhoria. Conseguiu-se ainda fazer alguns testes para uma possível substituição de alguns constituintes da tinta. Os componentes que entram na composição base da tinta aquosa, são de modo simplificado: ligante, pigmento, solvente e aditivos. Os constituintes que mais encarecem a tinta, e consequentemente o processo em causa, são o ligante e o pigmento. Os estudos efectuados precisam de ser aprofundados, na tentativa de melhorar o processo minimizando os custos de produção. Formalizaram-se os procedimentos escritos de produção STOCO tanto para o protótipo como para o processo industrial e elaborou-se uma ficha técnica de produto para a brita colorida STOCO.