Determination of tartaric acid in wines by FIA with tubular tartrate-selective electrodes

A flow injection analysis (FIA) system comprising a tartrate- (TAT) selective electrode has been developed for determination of tartaric acid in wines. Several electrodes constructed for this purpose had a PVC membrane with a complex of quaternary ammonium and TAT as anion exchanger, a phenol derivative as additive, and a more or less polar mediator solvent. Characterization of the electrodes showed behavior was best for membranes with o-nitrophenyl octyl ether as solvent. On injection of 500 μL into a phosphate buffer carrier (pH = 3.1; ionic strength 10–2 mol/L) flowing at 3 mL/min, the slope was 58.06 ± 0.6 with a lower limit of linear range of 5.0 × 10–4 mol/L TAT and R2 = 0.9989. The interference of several species, e.g. chloride, bromide, iodide, nitrate, gallic acid, tannin, sucrose, glucose, fructose, acetate, and citrate, was evaluated in terms of potentiometric selectivity coefficients. The Hofmeister series was followed for inorganic species and the most interfering organic ion was citrate. When red and white wines were analyzed and the results compared with those from an independent method they were found to be accurate, with relative standard deviations below 5.0%.

Citrate selective electrodes for the flow injection analysis of soft drinks, beers and pharmaceutical products

Aiming the establishment of simple and accurate readings of citric acid (CA) in complex samples, citrate (CIT) selective electrodes with tubular configuration and polymeric membranes plus a quaternary ammonium ion exchanger were constructed. Several selective membranes were prepared for this purpose, having distinct mediator solvents (with quite different polarities) and, in some cases, p-tert-octylphenol (TOP) as additive. The latter was used regarding a possible increase in selectivity. The general working characteristics of all prepared electrodes were evaluated in a low dispersion flow injection analysis (FIA) manifold by injecting 500µl of citrate standard solutions into an ionic strength (IS) adjuster carrier (10−2 mol l−1) flowing at 3ml min−1. Good potentiometric response, with an average slope and a repeatability of 61.9mV per decade and ±0.8%, respectively, resulted from selective membranes comprising additive and bis(2-ethylhexyl)sebacate (bEHS) as mediator solvent. The same membranes conducted as well to the best selectivity characteristics, assessed by the separated solutions method and for several chemical species, such as chloride, nitrate, ascorbate, glucose, fructose and sucrose. Pharmaceutical preparations, soft drinks and beers were analyzed under conditions that enabled simultaneous pH and ionic strength adjustment (pH = 3.2; ionic strength = 10−2 mol l−1), and the attained results agreed well with the used reference method (relative error < 4%). The above experimental conditions promoted a significant increase in sensitivity of the potentiometric response, with a supra-Nernstian slope of 80.2mV per decade, and allowed the analysis of about 90 samples per hour, with a relative standard deviation <1.0%.

Construction and evaluation of cysteine selective electrodes for FIA analysis of pharmaceuticals

A flow injection analysis (FIA) system comprising a cysteine selective electrode as detection system was developed for determination of this amino acid in pharmaceuticals. Several electrodes were constructed for this purpose, having PVC membranes with different ionic exchangers and mediator solvents. Better working characteristics were attained with membranes comprising o-nitrophenyl octyl ether as mediator solvent and a tetraphenylborate based ionic-sensor. Injection of 500 µL standard solutions into an ionic strength adjuster carrier (3x10-3 M) of barium chloride flowing at 2.4mL min-1, showed linearity ranges from 5.0x10-5 to 5.0x10-3 M, with slopes of 76.4±0.6mV decade-1 and R2>0.9935. Slope decreased significantly under the requirement of a pH adjustment, selected at 4.5. Interference of several compounds (sodium, potassium, magnesium, barium, glucose, fructose, and sucrose) was estimated by potentiometric selectivity coefficients and considered negligible. Analysis of real samples were performed and considered accurate, with a relative error to an independent method of +2.7%.

Ciprofloxacin-imprinted polymeric receptors as ionophores for potentiometric transduction

A 3D-mirror synthetic receptor for ciprofloxacin host–guest interactions and potentiometric transduction is presented. The host cavity was shaped on a polymeric surface assembled with methacrylic acid or 2-vinyl pyridine monomers by radical polymerization. Molecularly imprinted particles were dispersed in 2-nitrophenyl octyl ether and entrapped in a poly(vinyl chloride) matrix. The sensors exhibited a near-Nernstian response in steady state evaluations. Slopes and detection limits ranged from 26.8 to 50.0mVdecade−1 and 1.0×10−5 to 2.7×10−5 mol L−1, respectively. Good selectivity was observed for trimethoprim, enrofloxacin, tetracycline, cysteine, galactose, hydroxylamine, creatinine, ammonium chloride, sucrose, glucose, sulphamerazine and sulfadiazine. The sensors were successfully applied to the determination of ciprofloxacin concentrations in fish and in pharmaceuticals. The method presented offered the advantages of simplicity, accuracy, applicability to colored and turbid samples and automation feasibility, as well as confirming the use of molecularly imprinted polymers as ionophores for organic ion recognition in potentiometric transduction.

Artificial antibodies for troponin T by its imprinting on the surface of multiwalled carbon nanotubes: Its use as sensory surfaces

A novel artificial antibody for troponin T (TnT) was synthesized by molecular imprint (MI) on the surface of multiwalled carbon nanotubes (MWCNT). This was done by attaching TnT to the MWCNT surface, and filling the vacant spaces by polymerizing under mild conditions acrylamide (monomer) in N,N′-methylenebisacrylamide (cross-linker) and ammonium persulphate (initiator). After removing the template, the obtained biomaterial was able to rebind TnT and discriminate it among other interfering species. Stereochemical recognition of TnT was confirmed by the non-rebinding ability displayed by non-imprinted (NI) materials, obtained by imprinting without a template. SEM and FTIR analysis confirmed the surface modification of the MWCNT. The ability of this biomaterial to rebind TnT was confirmed by including it as electroactive compound in a PVC/plasticizer mixture coating a wire of silver, gold or titanium. Anionic slopes of 50 mV decade−1 were obtained for the gold wire coated with MI-based membranes dipped in HEPES buffer of pH 7. The limit of detection was 0.16 μg mL−1. Neither the NI-MWCNT nor the MWCNT showed the ability to recognize the template. Good selectivity was observed against creatinine, sucrose, fructose, myoglobin, sodium glutamate, thiamine and urea. The sensor was tested successfully on serum samples. It is expected that this work opens new horizons on the design of new artificial antibodies for complex protein structures.

Ciprofloxacin-imprinted polymeric receptors as ionophores for potentiometric transduction

A 3D-mirror synthetic receptor for ciprofloxacin host–guest interactions and potentiometric transduction is presented. The host cavity was shaped on a polymeric surface assembled with methacrylic acid or 2-vinyl pyridine monomers by radical polymerization. Molecularly imprinted particles were dispersed in 2-nitrophenyl octyl ether and entrapped in a poly(vinyl chloride) matrix. The sensors exhibited a near-Nernstian response in steady state evaluations. Slopes and detection limits ranged from 26.8 to 50.0 mV decade−1 and 1.0 × 10−5 to 2.7 × 10−5 mol L−1, respectively. Good selectivity was observed for trimethoprim, enrofloxacin, tetracycline, cysteine, galactose, hydroxylamine, creatinine, ammonium chloride, sucrose, glucose, sulphamerazine and sulfadiazine. The sensors were successfully applied to the determination of ciprofloxacin concentrations in fish and in pharmaceuticals. The method presented offered the advantages of simplicity, accuracy, applicability to colored and turbid samples and automation feasibility, as well as confirming the use of molecularly imprinted polymers as ionophores for organic ion recognition in potentiometric transduction.

Valorização da Borra de Café: Otimização da Produção de Biodiesel por Catálise Enzimática

O decréscimo das reservas de petróleo e as consequências ambientais resultantes do recurso a combustíveis fósseis nos motores a diesel têm levado à procura de combustíveis alternativos. Esta pesquisa alicerçada nas fontes de energia renovável tornou-se essencial, face à crescente procura de energia e ao limitado fornecimento de combustíveis fósseis . Resíduos de óleo de cozinha, gordura animal, entre outros resíduos de origem biológica, tais como a borra de café, são exemplos de matérias-primas para a produção de biodiesel. A sua valorização tem interesse quer pela perspetiva ambiental, quer pela económica, pois aumenta não só a flexibilidade e diversificação das matérias-primas, mas também contribui para uma estabilidade de custos e alteração nas políticas agrícolas e de uso do solo. É neste contexto que se enquadra o biodiesel e a borra de café, pretendendo-se aqui efetuar o estudo da produção, à escala laboratorial, de biodiesel a partir da borra de café, por transesterificação enzimática, visando a procura das melhores condições reacionais. Iniciando-se com a caracterização da borra de café, foram avaliados antes e após a extração do óleo da borra de café, diversos parâmetros, de entre os quais se destacam: o teor de humidade (16,97% e 6,79%), teor de cinzas (1,91 e 1,57%), teor de azoto (1,71 e 2,30%), teor de proteínas (10,7 e 14,4%), teor de carbono (70,2 e 71,7%), teor de celulose bruta (14,77 e 18,48%), teor de lenhina (31,03% e 30,97%) e poder calorifico superior (19,5 MJ/kg e 19,9 MJ/kg). Sumariamente, constatou-se que os valores da maioria dos parâmetros não difere substancialmente dos valores encontrados na literatura, tendo sido evidenciado o potencial da utilização desta biomassa, como fonte calorifica para queima e geração de energia. Sendo a caracterização do óleo extraído da borra de café um dos objetivos antecedentes à produção do biodiesel, pretendeu-se avaliar os diferentes parâmetros mais significativos. No que diz respeito à caracterização do óleo extraído, distingue-se a sua viscosidade cinemática (38,04 mm2/s), densidade 0,9032 g/cm3, poder calorífico de 37,9 kcal/kg, índice de iodo igual a 63,0 gI2/ 100 g óleo, o teor de água do óleo foi de 0,15 %, o índice de acidez igual a 44,8 mg KOH/g óleo, ponto de inflamação superior a 120 ºC e teor em ácidos gordos de 82,8%. Inicialmente foram efetuados ensaios preliminares, a fim de selecionar a lipase (Lipase RMIM, TL 100L e CALB L) e álcool (metanol ou etanol puros) mais adequados à produção de biodiesel, pelo que o rendimento de 83,5% foi obtido através da transesterificação mediada pela lipase RMIM, utilizando como álcool o etanol. Sendo outro dos objetivos a otimização do processo de transesterificação enzimática, através de um desenho composto central a três variáveis (razão molar etanol: óleo, concentração de enzima e temperatura), recorrendo ao software JMP 8.0, determinou-se como melhores condições, uma razão molar etanol: óleo 5:1, adição de 4,5% (m/m) de enzima e uma temperatura de 45 ºC, que conduziram a um rendimento experimental equivalente a 96,7 % e teor de ésteres 87,6%. Nestas condições, o rendimento teórico foi de 99,98%. Procurou-se ainda estudar o efeito da adição de água ao etanol, isto é, o efeito da variação da concentração do etanol pela adição de água, para teores de etanol de 92%, 85% e 75%. Verificou-se que até 92% decorreu um aumento da transesterificação (97,2%) para um teor de ésteres de (92,2%), pelo que para teores superiores de água adicionada (75% e 85%) ocorreu um decréscimo no teor final em ésteres (77,2% e 89,9%) e no rendimento da reação (84,3% e 91,9%). Isto indica a ocorrência da reação de hidrólise em maior extensão, que leva ao desvio do equilíbrio no sentido contrário à reação de formação dos produtos, isto é, dos ésteres. Finalmente, relativamente aos custos associados ao processo de produção de biodiesel, foram estimados para o conjunto de 27 ensaios realizados neste trabalho, e que corresponderam a 767,4 g de biodiesel produzido, sendo o custo dos reagentes superior ao custo energético, de 156,16 € e 126,02 €, respetivamente. Naturalmente que não esperamos que, a nível industrial os custos sejam desta ordem de grandeza, tanto mais que há economia de escala e que as enzimas utilizadas no processo deveriam ser reutilizadas diversas vezes.