Effect of plug-filling, Testing velocity and temperature on the tensile strength of strap repairs on aluminium structures

In this work, an experimental study was performed on the influence of plug-filling, loading rate and temperature on the tensile strength of single-strap (SS) and double-strap (DS) repairs on aluminium structures. Whilst the main purpose of this work was to evaluate the feasibility of plug-filling for the strength improvement of these repairs, a parallel study was carried out to assess the sensitivity of the adhesive to external features that can affect the repairs performance, such as the rate of loading and environmental temperature. The experimental programme included repairs with different values of overlap length (L O = 10, 20 and 30 mm), and with and without plug-filling, whose results were interpreted in light of experimental evidence of the fracture modes and typical stress distributions for bonded repairs. The influence of the testing speed on the repairs strength was also addressed (considering 0.5, 5 and 25 mm/min). Accounting for the temperature effects, tests were carried out at room temperature (≈23°C), 50 and 80°C. This permitted a comparative evaluation of the adhesive tested below and above the glass transition temperature (T g), established by the manufacturer as 67°C. The combined influence of these two parameters on the repairs strength was also analysed. According to the results obtained from this work, design guidelines for repairing aluminium structures were

Single-lap joints of similar and dissimilar adherends bonded with an acrylic adhesive

In this study, the tensile strength of single-lap joints (SLJs) between similar and dissimilar adherends bonded with an acrylic adhesive was evaluated experimentally and numerically. The adherend materials included polyethylene (PE), polypropylene (PP), carbon-epoxy (CFRP), and glass-polyester (GFRP) composites. The following adherend combinations were tested: PE/PE, PE/PP, PE/CFRP, PE/GFRP, PP/PP, CFRP/CFRP, and GFRP/GFRP. One of the objectives of this work was to assess the influence of the adherends stiffness on the strength of the joints since it significantly affects the peel stresses magnitude in the adhesive layer. The experimental results were also used to validate a new mixed-mode cohesive damage model developed to simulate the adhesive layer. Thus, the experimental results were compared with numerical simulations performed in ABAQUS®, including a developed mixed-mode (I+II) cohesive damage model, based on the indirect use of fracture mechanics and implemented within interface finite elements. The cohesive laws present a trapezoidal shape with an increasing stress plateau, to reproduce the behaviour of the ductile adhesive used. A good agreement was found between the experimental and numerical results.

Estudo da Resistência Mecânica do Betão com Agregado Cerâmico Vermelho

Os sectores da construção e demolição de edifícios são responsáveis por um elevado volume de produção de resíduos. Estes resíduos são normalmente direcionados para aterros, que se encontram, neste momento, sobrelotados. Esta falta de capacidade de receção de resíduos tem como consequência imediata o aumento dos valores monetários associados ao depósito destes materiais excedentários. Com a elevada produção destes resíduos torna-se importante a sua reciclagem e reutilização. No caso da Engenharia Civil, uma grande produtora de resíduos, seria ainda mais interessante o seu reaproveitamento imediato na área. Nesta investigação, pretendeu-se avaliar o desempenho mecânico de betões com diferentes percentagens de agregados cerâmicos vermelhos. Essa investigação passou numa fase inicial pelo estado fresco do betão, de forma a analisar a sua trabalhabilidade. Na fase seguinte, analisou-se no estado endurecido, a resistência à compressão e resistência à tração por compressão diametral. Para concretização deste objetivo produziram-se três tipos de betões: um de referência (areia fina e brita fina), um betão com incorporação de agregados finos e grossos de cerâmica vermelha, juntamente com a areia fina e a brita fina, e o terceiro, um betão com a substituição total da areia fina por cerâmica fina. A realização desta investigação, demostrou que os betões com a incorporação de agregado cerâmico vermelho apresentam resultados de boa qualidade, sendo plausível a sua utilização em estruturas.