Modelling real solar cell using PSCAD/MATLAB

This paper presents the development of a solar photovoltaic (PV) model based on PSCAD/EMTDC - Power System Computer Aided Design – including a mathematical model study. An additional algorithm has been implemented in MATLAB software in order to calculate several parameters required by the PSCAD developed model. All the simulation study has been performed in PSCAD/MATLAB software simulation tool. A real data base concerning irradiance, cell temperature and PV power generation was used in order to support the evaluation of the implemented PV model.

Effect of the compact Ti layer on the efficiency of dye-sensitized solar cells assembled using stainless steel sheets

Titanium films have been deposited on stainless steel metal sheets using dc magnetron sputtering technique at different substrate temperatures. The structure of the titanium films strongly depend on the substrate temperature. The titanium film deposited at the substrate temperature lower than 300 ◦C has a loose flat sheet grains structure and the titanium film prepared at the substrate temperature higher than 500 ◦C has a dense nubby grains structure. The DSSC assembled using stainless steel sheet coated with titanium film deposited at high substrate temperature has a low charge transfer resistance in the TiO2/Ti interface and results in a high conversion efficiency. The DSSC assembled using stainless steel sheet coated with titanium film deposited at temperature higher than 500 ◦C has higher conversion efficiency than that assembled using titanium metal sheet as the substrate. The maximum conversion efficiency, 2.26% is obtained for DSSC assembled using stainless steel sheet coated with titanium film deposited at 700 ◦C substrate temperature, which is about 70% of the conversion efficiency of the FTO reference cell used in this study.

Efficient implementation of a dominance protocol for wireless medium access

Mestrado em Engenharia Electrotécnica e de Computadores

Software de apoio à implementação de sistemas híbridos de produção de energia eléctrica baseados em energias renováveis

O aumento da população Mundial, particularmente em Países emergentes como é o caso da China e da Índia, tem-se relevado um problema adicional no que confere às dificuldades associadas ao consumo mundial de energia, pois esta situação limita inequivocamente o acesso destes milhões de pessoas à energia eléctrica para os bens básicos de sobrevivência. Uma das muitas formas de se extinguir esta necessidade, começa a ser desenvolvida recorrendo ao uso de recursos renováveis como fontes de energia. Independentemente do local do mundo onde nos encontremos, essas fontes de energia são abundantes, inesgotáveis e gratuitas. O problema reside na forma como esses recursos renováveis são geridos em função das solicitações de carga que as instalações necessitam. Sistemas híbridos podem ser usados para produzir energia em qualquer parte do mundo. Historicamente este tipo de sistemas eram aplicados em locais isolados, mas nos dias que correm podem ser usados directamente conectados à rede, permitindo que se realize a venda de energia. Foi neste contexto que esta tese foi desenvolvida, com o objectivo de disponibilizar uma ferramenta informática capaz de calcular a rentabilidade de um sistema híbrido ligado à rede ou isolado. Contudo, a complexidade deste problema é muito elevada, pois existe uma extensa panóplia de características e distintos equipamentos que se pode adoptar. Assim, a aplicação informática desenvolvida teve de ser limitada e restringida aos dados disponíveis de forma a poder tornar-se genérica, mas ao mesmo tempo permitir ter uma aplicabilidade prática. O objectivo da ferramenta informática desenvolvida é apresentar de forma imediata os custos da implementação que um sistema híbrido pode acarretar, dependendo apenas de três variáveis distintas. A primeira variável terá de ter em consideração o local de instalação do sistema. Em segundo lugar é o tipo de ligação (isolado ou ligado à rede) e, por fim, o custo dos equipamentos (eólico, solar e restantes componentes) que serão introduzidos. Após a inserção destes dados a aplicação informática apresenta valores estimados de Payback e VAL.

Traceability-based access recommendation

Devido à grande quantidade de dados disponíveis na Internet, um dos maiores desafios no mundo virtual é recomendar informação aos seus utilizadores. Por outro lado, esta grande quantidade de dados pode ser útil para melhorar recomendações se for anotada e interligada por dados de proveniência. Neste trabalho é abordada a temática de recomendação de (alteração de) permissões acesso sobre recursos ao seu proprietário, ao invés da recomendação do próprio recurso a um potencial consumidor/leitor. Para permitir a recomendação de acessos a um determinado recurso, independentemente do domínio onde o mesmo se encontra alojado, é essencial a utilização de sistemas de controlo de acessos distribuídos, mecanismos de rastreamento de recursos e recomendação independentes do domínio. Assim sendo, o principal objectivo desta tese é utilizar informação de rastreamento de acções realizadas sobre recursos (i.e. informação que relaciona recursos e utilizadores através da Web independentemente do domínio de rede) e utiliza-la para permitir a recomendação de privilégios de acesso a esses recursos por outros utilizadores. Ao longo do desenvolvimento da tese resultaram as seguintes contribuições: A análise do estado da arte de recomendação e de sistemas de recomendação potencialmente utilizáveis na recomendação de privilégios (secção 2.3); A análise do estado da arte de mecanismos de rastreamento e proveniência de informação (secção 2.2); A proposta de um sistema de recomendação de privilégios de acesso independente do domínio e a sua integração no sistema de controlo de acessos proposto anteriormente (secção 3.1); Levantamento, análise e especificação da informação relativa a privilégios de acesso, para ser utilizada no sistema de recomendação (secção 2.1); A especificação da informação resultante do rastreamento de acções para ser utilizada na recomendação de privilégios de acesso (secção 4.1.1); A especificação da informação de feedback resultante do sistema de recomendação de acessos e sua reutilização no sistema de recomendação(secção 4.1.3); A especificação, implementação e integração do sistema de recomendação de privilégios de acesso na plataforma já existente (secção 4.2 e secção 4.3); Realização de experiências de avaliação ao sistema de recomendação de privilégios, bem como a análise dos resultados obtidos (secção 5).

Structural modification of TiO2 nanorod films with an influence on the photovoltaic efficiency of a dye-sensitized solar cell (DSSC).

TiO2 nanorod films have been deposited on ITO substrates by dc reactive magnetron sputtering technique. The structures of these nanorod films were modified by the variation of the oxygen pressure during the sputtering process. Although all these TiO2 nanorod films deposited at different oxygen pressures show an anatase structure, the orientation of the nanorod films varies with the oxygen pressure. Only a very weak (101) diffraction peak can be observed for the TiO2 nanorod film prepared at low oxygen pressure. However, as the oxygen pressure is increased, the (220) diffraction peak appears and the intensity of this diffraction peak is increased with the oxygen pressure. The results of the SEM show that these TiO2 nanorods are perpendicular to the ITO substrate. At low oxygen pressure, these sputtered TiO2 nanorods stick together and have a dense structure. As the oxygen pressure is increased, these sputtered TiO2 nanorods get separated gradually and have a porous structure. The optical transmittance of these TiO2 nanorod films has been measured and then fitted by OJL model. The porosities of the TiO2 nanorod films have been calculated. The TiO2 nanorod film prepared at high oxygen pressure shows a high porosity. The dye-sensitized solar cells (DSSCs) have been assembled using these TiO2 nanorod films prepared at different oxygen pressures as photoelectrode. The optimum performance was achieved for the DSSC using the TiO2 nanorod film with the highest (220) diffraction peak and the highest porosity.

Effects of sulphurization time on Cu2ZnSnS4 absorbers and thin films solar cells obtained from metallic precursors

We report the results of a study of the sulphurization time effects on Cu2ZnSnS4 absorbers and thin film solar cells prepared from dc-sputtered tackedmetallic precursors. Three different time intervals, 10 min, 30min and 60 min, at maximum sulphurization temperature were considered. The effects of this parameter' change were studied both on the absorber layer properties and on the final solar cell performance. The composition, structure, morphology and thicknesses of the CZTS layers were analyzed. The electrical characterization of the absorber layer was carried out by measuring the transversal electrical resistance of the samples as a function of temperature. This study shows an increase of the conductivity activation energy from 10 meV to 54meV for increasing sulphurization time from 10min to 60min. The solar cells were built with the following structure: SLG/Mo/CZTS/CdS/i-ZnO/ZnO:Al/Ni:Al grid. Several ac response equivalent circuit models were tested to fit impedance measurements. The best results were used to extract the device series and shunt resistances and capacitances. Absorber layer's electronic properties were also determined using the Mott–Schottky method. The results show a decrease of the average acceptor doping density and built-in voltage, from 2.0 1017 cm−3 to 6.5 1015 cm−3 and from 0.71 V to 0.51 V, respectively, with increasing sulphurization time. These results also show an increase of the depletion region width from approximately 90 nm–250 nm.

Admittance spectroscopy of Cu2ZnSnS4 based thin film solar cells

In this report, we propose an AC response equivalent circuit model to describe the admittance measurements of Cu2ZnSnS4 thin film solar cell grown by sulphurization of stacked metallic precursors. This circuit describes the contact resistances, the back contact, and the heterojunction with two trap levels. The study of the back contact resistance allowed the estimation of a back contact barrier of 246 meV. The analysis of the trap series with varying temperature revealed defect activation energies of 45 meV and 113 meV. The solar cell’s electrical parameters were obtained from the J-V curve: conversion efficiency, 1.21%; fill factor, 50%; open circuit voltage, 360 mV; and short circuit current density, 6.8 mA/cm2.

Cu2ZnSnS4 solar cells prepared with sulphurized dc-sputtered stacked metallic precursors

In the present work we report the details of the preparation and characterization results of Cu2ZnSnS4 (CZTS) based solar cells. The CZTS absorber was obtained by sulphurization of dc magnetron sputtered Zn/Sn/Cu precursor layers. The morphology, composition and structure of the absorber layer were studied by scanning electron microscopy, energy dispersive spectroscopy, X-ray diffraction and Raman scattering. The majority carrier type was identified via a hot point probe analysis. The hole density, space charge region width and band gap energy were estimated from the external quantum efficiency measurements. A MoS2 layer that formed during the sulphurization process was also identified and analyzed in this work. The solar cells had the following structure: soda lime glass/Mo/CZTS/CdS/i-ZnO/ZnO:Al/Al grid. The best solar cell showed an opencircuit voltage of 345 mV, a short-circuit current density of 4.42 mA/cm2, a fill factor of 44.29% and an efficiency of 0.68% under illumination in simulated standard test conditions: AM 1.5 and 100 mW/cm2.

Growth and characterization of Cu2ZnSn(S,Se)4 thin films for solar cells

Cu2ZnSnS4 (CZTS) and Cu2ZnSnSe4 (CZTSe) with their band gap energies around 1.45 eV and 1.0 eV, respectively, can be used as the absorber layer in thin film solar cells. By using a mixture of both compounds, Cu2ZnSn(S,Se)4 (CZTSSe), a band gap tuning may be possible. The latter material has already shown promising results such as solar cell efficiencies up to 10.1%. In this work, CZTSSe thin films were grown in order to study its structure and to establish the best growth precursors. SEM micrographs reveal an open columnar structure for most samples and EDS composition profiling of the cross sections show different selenium gradients. X-ray diffractograms show different shifts of the kesterite/stannite (1 1 2) peak, which indicate the presence of CZTSSe. From Raman scattering analysis, it was concluded that all samples had traces of CZTS and CZTSSe. The composition of the CZTSSe layer was estimated using X-ray diffraction and Raman scattering and both results were compared. It was concluded that Se diffused more easily in precursors with ternary Cu–Sn–S phases and metallic Zn than in precursors with ZnS and/or CZTS already formed. It was also showed that a combination of X-ray diffraction and Raman scattering can be used to estimate the ratio of S per Se in CZTSSe samples.

Access and use of european information: a comparative analysis

This paper presents some results of a survey on access to European information among a group of 234 users of 55 European Documentation Centres (EDCs), from 21 European Union (EU) Member-States. The findings of the questionnaire made to 88 EDCs' managers, from 26 EU Member-States, will also be analyse. Two different points of view regarding issues related to reasons to access European information, the valued aspects during that access and the use of European databases will be compare.

Using a prioritized medium access control protocol for incrementally obtaining an interpolation of sensor readings

This paper addresses sensor network applications which need to obtain an accurate image of physical phenomena and do so with a high sampling rate in both time and space. We present a fast and scalable approach for obtaining an approximate representation of all sensor readings at high sampling rate for quickly reacting to critical events in a physical environment. This approach is an improvement on previous work in that after the new approach has undergone a startup phase then the new approach can use a very small sampling period.

WiDom: a dominance protocol for wireless medium access

In this paper, we address the problem of sharing a wireless channel among a set of sporadic message streams where a message stream issues transmission requests with real-time deadlines. We propose a collision-free wireless medium access control (MAC) protocol which implements static-priority scheduling, supports a large number of priority levels and is fully distributed. It is an adaptation to a wireless channel of the dominance protocol used in the CAN bus. But, unlike that protocol, our protocol does not require a node having the ability to receive an incoming bit from the channel while transmitting to the channel. The evaluation of the protocol with real embedded computing platforms is presented to show that the proposed protocol is in fact collision-free and prioritized. We measure the response times of our implementation and show that the response-time analysis developed for the protocol offers an upper bound on the response times.

Delay-bounded medium access for unidirectional wireless links

Consider a wireless network where links may be unidirectional, that is, a computer node A can broadcast a message and computer node B will receive this message but if B broadcasts then A will not receive it. Assume that messages have deadlines. We propose a medium access control (MAC) protocol which replicates a message in time with carefully selected pauses between replicas, and in this way it guarantees that for every message at least one replica of that message is transmitted without collision. The protocol ensures this with no knowledge of the network topology and it requires neither synchronized clocks nor carrier sensing capabilities. We believe this result is significant because it is the only MAC protocol that offers an upper bound on the message queuing delay for unidirectional links without relying on synchronized clocks.

Preliminary discussion on globally prioritized medium access for multi-channel wireless systems

We discuss the development of a simple globally prioritized multi-channel medium access control (MAC) protocol for wireless networks. This protocol provides “hard” pre-run-time real-time guarantees to sporadic message streams, exploits a very large fraction of the capacity of all channels for “hard” real-time traffic and also makes it possible to fully utilize the channels with non real-time traffic when hard real-time messages do not request to be transmitted. The potential of such protocols for real-time applications is discussed and a schedulability analysis is also presented.