Microstructure, mechanical properties and chemical degradation of brazed AISI 316 stainless steel/alumina systems

The main aims of the present study are simultaneously to relate the brazing parameters with: (i) the correspondent interfacial microstructure, (ii) the resultant mechanical properties and (iii) the electrochemical degradation behaviour of AISI 316 stainless steel/alumina brazed joints. Filler metals on such as Ag–26.5Cu–3Ti and Ag–34.5Cu–1.5Ti were used to produce the joints. Three different brazing temperatures (850, 900 and 950 °C), keeping a constant holding time of 20 min, were tested. The objective was to understand the influence of the brazing temperature on the final microstructure and properties of the joints. The mechanical properties of the metal/ceramic (M/C) joints were assessed from bond strength tests carried out using a shear solicitation loading scheme. The fracture surfaces were studied both morphologically and structurally using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction analysis (XRD). The degradation behaviour of the M/C joints was assessed by means of electrochemical techniques. It was found that using a Ag–26.5Cu–3Ti brazing alloy and a brazing temperature of 850 °C, produces the best results in terms of bond strength, 234 ± 18 MPa. The mechanical properties obtained could be explained on the basis of the different compounds identified on the fracture surfaces by XRD. On the other hand, the use of the Ag–34.5Cu–1.5Ti brazing alloy and a brazing temperature of 850 °C produces the best results in terms of corrosion rates (lower corrosion current density), 0.76 ± 0.21 μA cm−2. Nevertheless, the joints produced at 850 °C using a Ag–26.5Cu–3Ti brazing alloy present the best compromise between mechanical properties and degradation behaviour, 234 ± 18 MPa and 1.26 ± 0.58 μA cm−2, respectively. The role of Ti diffusion is fundamental in terms of the final value achieved for the M/C bond strength. On the contrary, the Ag and Cu distribution along the brazed interface seem to play the most relevant role in the metal/ceramic joints electrochemical performance.

Estudo das principais argamassas utilizadas na reabilitação de edifícios antigos

Com o passar dos anos, as obras mais sublimes, começam a mostrar marcas subtis ou profundas de deterioração, como por exemplo: fissurações e defeitos associados à humidade. Estes são reflexo de fatores externos, como fungos, a própria atmosfera reativa, mudanças climatéricas e, até mesmo, a ação do homem. Neste seguimento pretende-se estudar as principais argamassas utilizadas na reabilitação de edifícios antigos, principalmente, as argamassas utilizadas no decorrer das obras ao longo do estágio, com o objetivo de comparar as suas caraterísticas, sendo estas argamassas tradicionais e pré-fabricadas. Foram feitos vários ensaios para determinar as suas resistências mecânicas, nomeadamente, o ensaio de resistência à flexão e compressão em diferentes idades após a confeção das argamassas, e ensaios para determinar a sua durabilidade como o ensaio de absorção da água por capilaridade; ensaio de absorção de água por imersão às 48horas (pressão atmosférica); ensaio para determinação do teor de água às 48horas e o ensaio de arrancamento (pull-off). A análise dos resultados mostrou que as argamassas adquirem mais resistência com o passar do tempo após a sua confeção, e que as argamassas dos provetes obtidos de forma tradicional, constituídos por argamassa de cal Hidráulica (HL5) e argamassa de cimento, apresentam melhores resultados do que a argamassa pré-fabricada (weber.cal classic).

Shear strength of adhesively bonded polyolefins with minimal surface preparation

Interest in polyethylene and polypropylene bonding has increased in the last years. However, adhesive joints with adherends which are of low surface energy and which are chemically inert present several difficulties. Generally, their high degree of chemical resistance to solvents and dissimilar solubility parameters limit the usefulness of solvent bonding as a viable assembly technique. One successful approach to adhesive bonding of these materials involves proper selection of surface pre-treatment prior to bonding. With the correct pre-treatment it is possible to glue these materials with one or more of several adhesives required by the applications involved. A second approach is the use of adhesives without surface pre-treatment, such as hot melts, high tack pressure-sensitive adhesives, solvent-based specialty adhesives and, more recently, structural acrylic adhesives as such 3M DP-8005® and Loctite 3030®. In this paper, the shear strengths of two acrylic adhesives were evaluated using the lap shear test method ASTM D3163 and the block shear test method ASTM D4501. Two different industrial polyolefins (polyethylene and polypropylene) were used for adherends. However, the focus of this study was to measure the shear strength of polyethylene joints with acrylic adhesives. The effect of abrasion was also studied. Some test specimens were manually abraded using 180 and 320 grade abrasive paper. An additional goal of this work was to examine the effect of temperature and moisture on mechanical strength of adhesive joints.