Efeitos tridimensionais no escoamento em torno de cilindros confinados

Mestrado em Engenharia Química

Sistema de aquisição de dados em tempo real

Neste trabalho propus-me realizar um Sistema de Aquisição de Dados em Tempo Real via Porta Paralela. Para atingir com sucesso este objectivo, foi realizado um levantamento bibliográfico sobre sistemas operativos de tempo real, salientando e exemplificando quais foram marcos mais importantes ao longo da sua evolução. Este levantamento permitiu perceber o porquê da proliferação destes sistemas face aos custos que envolvem, em função da sua aplicação, bem como as dificuldades, científicas e tecnológicas, que os investigadores foram tendo, e que foram ultrapassando com sucesso. Para que Linux se comporte como um sistema de tempo real, é necessário configura-lo e adicionar um patch, como por exemplo o RTAI ou ADEOS. Como existem vários tipos de soluções que permitem aplicar as características inerentes aos sistemas de tempo real ao Linux, foi realizado um estudo, acompanhado de exemplos, sobre o tipo de arquitecturas de kernel mais utilizadas para o fazer. Nos sistemas operativos de tempo real existem determinados serviços, funcionalidades e restrições que os distinguem dos sistemas operativos de uso comum. Tendo em conta o objectivo do trabalho, e apoiado em exemplos, fizemos um pequeno estudo onde descrevemos, entre outros, o funcionamento escalonador, e os conceitos de latência e tempo de resposta. Mostramos que há apenas dois tipos de sistemas de tempo real o ‘hard’ que tem restrições temporais rígidas e o ‘soft’ que engloba as restrições temporais firmes e suaves. As tarefas foram classificadas em função dos tipos de eventos que as despoletam, e evidenciando as suas principais características. O sistema de tempo real eleito para criar o sistema de aquisição de dados via porta paralela foi o RTAI/Linux. Para melhor percebermos o seu comportamento, estudamos os serviços e funções do RTAI. Foi dada especial atenção, aos serviços de comunicação entre tarefas e processos (memória partilhada e FIFOs), aos serviços de escalonamento (tipos de escalonadores e tarefas) e atendimento de interrupções (serviço de rotina de interrupção - ISR). O estudo destes serviços levou às opções tomadas quanto ao método de comunicação entre tarefas e serviços, bem como ao tipo de tarefa a utilizar (esporádica ou periódica). Como neste trabalho, o meio físico de comunicação entre o meio ambiente externo e o hardware utilizado é a porta paralela, também tivemos necessidade de perceber como funciona este interface. Nomeadamente os registos de configuração da porta paralela. Assim, foi possível configura-lo ao nível de hardware (BIOS) e software (módulo do kernel) atendendo aos objectivos do presente trabalho, e optimizando a utilização da porta paralela, nomeadamente, aumentando o número de bits disponíveis para a leitura de dados. No desenvolvimento da tarefa de hard real-time, foram tidas em atenção as várias considerações atrás referenciadas. Foi desenvolvida uma tarefa do tipo esporádica, pois era pretendido, ler dados pela porta paralela apenas quando houvesse necessidade (interrupção), ou seja, quando houvesse dados disponíveis para ler. Desenvolvemos também uma aplicação para permitir visualizar os dados recolhidos via porta paralela. A comunicação entre a tarefa e a aplicação é assegurada através de memória partilhada, pois garantindo a consistência de dados, a comunicação entre processos do Linux e as tarefas de tempo real (RTAI) que correm ao nível do kernel torna-se muito simples. Para puder avaliar o desempenho do sistema desenvolvido, foi criada uma tarefa de soft real-time cujos tempos de resposta foram comparados com os da tarefa de hard real-time. As respostas temporais obtidas através do analisador lógico em conjunto com gráficos elaborados a partir destes dados, mostram e comprovam, os benefícios do sistema de aquisição de dados em tempo real via porta paralela, usando uma tarefa de hard real-time.

Nova metodologia de execução do ensaio SCPTu com avaliação da influência da fonte sísmica quanto à sua dimensão e afastamento

O objectivo deste trabalho consiste na determinação das Ondas de Corte, onda S, através de uma nova metodologia de ensaio do piezocone sísmico, SCPTu. A nova metodologia adoptada de aquisição de dados, consiste na aquisição da onde de corte no movimento ascendente de remoção de varas, após execução do já conhecido ensaio CPTu, ao invés da tradicional aquisição, no movimento descendente, previamente ao acréscimo de nova vara. Além da introdução de uma nova metodologia de aquisição sísmica, tentou-se avaliar a influência da dimensão da fonte geradora da onda de corte e a influência do afastamento das mesmas ao ponto de cravação, do ensaio de penetração estática mencionado. Na avaliação das influências foram usadas três fontes de madeira de secção rectangular, com uma chapa de ferro a topo e diferenciadas entre si pelas dimensões de 1m, 2m e 3m e afastamentos até 4m.

Analysis and visualization of seismic data using mutual information

Seismic data is difficult to analyze and classical mathematical tools reveal strong limitations in exposing hidden relationships between earthquakes. In this paper, we study earthquake phenomena in the perspective of complex systems. Global seismic data, covering the period from 1962 up to 2011 is analyzed. The events, characterized by their magnitude, geographic location and time of occurrence, are divided into groups, either according to the Flinn-Engdahl (F-E) seismic regions of Earth or using a rectangular grid based in latitude and longitude coordinates. Two methods of analysis are considered and compared in this study. In a first method, the distributions of magnitudes are approximated by Gutenberg-Richter (G-R) distributions and the parameters used to reveal the relationships among regions. In the second method, the mutual information is calculated and adopted as a measure of similarity between regions. In both cases, using clustering analysis, visualization maps are generated, providing an intuitive and useful representation of the complex relationships that are present among seismic data. Such relationships might not be perceived on classical geographic maps. Therefore, the generated charts are a valid alternative to other visualization tools, for understanding the global behavior of earthquakes.

Enhancing the real-time capabilities of the Linux Kernel

The mainline Linux Kernel is not designed forhard real-time systems; it only fits the requirements of soft realtimesystems. In recent years, a kernel developer communityhas been working on the PREEMPT-RT patch. This patch(that aims to get a fully preemptible kernel) adds some realtimecapabilities to the Linux kernel. However, in terms ofscheduling policies, the real-time scheduling class of Linux islimited to the First-In-First-Out (SCHED_FIFO) and Round-Robin (SCHED_RR) scheduling policies. These scheduling policiesare however quite limited in terms of realtime performance.Therefore, in this paper, we report one importantcontribution for adding more advanced real-time capabilitiesto the Linux Kernel. Specifically, we describe modificationsto the (PREEMPT-RT patched) Linux kernel to supportreal-time slot-based task-splitting scheduling algorithms. Ourpreliminary evaluation shows that our implementation exhibitsa real-time performance that is superior to the schedulingpolicies provided by the current version of PREMPT-RT. Thisis a significant add-on to a widely adopted operating system.

Strap repair optimization by using embedded patches

Adhesively-bonded techniques offer an attractive option for repair of aluminium structures, and currently there are three widely used configurations, i.e., single-strap (SS), double-strap (DS) and scarf repairs. SS and DS repairs are straightforward to execute but stresses in the adhesive layer peak at the ends of the overlap. DS repairs additionally require both sides of the damaged structures to be reachable for repair, which is often not possible. In these repair configurations, some limitations emerge such as the weight, aerodynamic performance and aesthetics. The scarf repair is more complex to fabricate but stresses are more uniform along the adhesive bondline. Few studies of SS and DS repairs with embedded patches, such that these are completely flush with the adherends, are available in the literature. Furthermore, no data is available about the effects of geometrical and material parameters (e.g. the Young’s modulus of adhesive, E) on the mechanical behaviour optimization of embedded repairs. For this purpose, in this work standard SS and DD repairs, and also with embedded patches in the adherends, were tested under tension to allow the geometry optimization, by varying the overlap length (LO), thus allowing the maximization of the repairs strength. The influence of the patch embedding technique, showing notorious advantages such as aerodynamic or aesthetics, was compared in strength with standard strap repairs, for the viability analysis of its implementation. As a result of this work, some conclusions were drawn for the design optimization of bonded repairs on aluminium structures.

Numerical and experimental study of tensile strength of single and double-strap repairs

Adhesive bonding as a joining or repair method has a wide application in many industries. Repairs with bonded patches are often carried out to re-establish the stiffness at critical regions or spots of corrosion and/or fatigue cracks. Single and double-strap repairs (SS and DS, respectively) are a viable option for repairing. For the SS repairs, a patch is adhesively-bonded on one of the structure faces. SS repairs are easy to execute, but the load eccentricity leads to peel peak stresses at the overlap edges. DS repairs involve the use of two patches, one on each face of the structure. These are more efficient than SS repairs, due to the doubling of the bonding area and suppression of the transverse deflection of the adherends. Shear stresses also become more uniform as a result of smaller differential straining. The experimental and Finite Element (FE) study presented here for strength prediction and design optimization of bonded repairs includes SS and DS solutions with different values of overlap length (LO). The examined values of LO include 10, 20 and 30 mm. The failure strengths of the SS and DS repairs were compared with FE results by using the Abaqus® FE software. A Cohesive Zone Model (CZM) with a triangular shape in pure tensile and shear modes, including the mixed-mode possibility for crack growth, was used to simulate fracture of the adhesive layer. A good agreement was found between the experiments and the FE simulations on the failure modes, elastic stiffness and strength of the repairs, showing the effectiveness and applicability of the proposed FE technique in predicting strength of bonded repairs. Furthermore, some optimization principles were proposed to repair structures with adhesively-bonded patches that will allow repair designers to effectively design bonded repairs.

Using a cohesive damage model to predict the tensile behaviour of CFRP single-strap repairs

This work addresses both experimental and numerical analyses regarding the tensile behaviour of CFRP single-strap repairs. Two fundamental geometrical parameters were studied: overlap length and patch thickness. The numerical model used ABAQUS® software and a developed cohesive mixed-mode damage model adequate for ductile adhesives, and implemented within interface finite elements. Stress analyses and strength predictions were carried out. Experimental and numerical comparisons were performed on failure modes, failure load and equivalent stiffness of the repair. Good correlation was found between experimental and numerical results, showing that the proposed model can be successfully applied to bonded joints or repairs.

Experimental and numerical evaluation of composite repairs on wood beams damaged by cross-graining

An experimental and Finite Element study was performed on the bending behaviour of wood beams of the Pinus Pinaster species repaired with adhesively-bonded carbon–epoxy patches, after sustaining damage by cross-grain failure. This damage is characterized by crack growth at a small angle to the beams longitudinal axis, due to misalignment between the wood fibres and the beam axis. Cross-grain failure can occur in large-scale in a wood member when trees that have grown spirally or with a pronounced taper are cut for lumber. Three patch lengths were tested. The simulations include the possibility of cohesive fracture of the adhesive layer, failure within the wood beam in two propagation planes and patch interlaminar failure, by the use of cohesive zone modelling. The respective cohesive properties were estimated either by an inverse method or from the literature. The comparison with the tests allowed the validation of the proposed methodology, opening a good perspective for the reduction of costs in the design stages of these repairs due to extensive experimentation.

Buckling strength of adhesively-bonded single and double-strap repairs on carbon-epoxy structures

This work reports on an experimental and finite element method (FEM) parametric study of adhesively-bonded single and double-strap repairs on carbon-epoxy structures under buckling unrestrained compression. The influence of the overlap length and patch thickness was evaluated. This loading gains a particular significance from the additional characteristic mechanisms of structures under compression, such as fibres microbuckling, for buckling restrained structures, or global buckling of the assembly, if no transverse restriction exists. The FEM analysis is based on the use of cohesive elements including mixed-mode criteria to simulate a cohesive fracture of the adhesive layer. Trapezoidal laws in pure modes I and II were used to account for the ductility of most structural adhesives. These laws were estimated for the adhesive used from double cantilever beam (DCB) and end-notched flexure (ENF) tests, respectively, using an inverse technique. The pure mode III cohesive law was equalled to the pure mode II one. Compression failure in the laminates was predicted using a stress-based criterion. The accurate FEM predictions open a good prospect for the reduction of the extensive experimentation in the design of carbon-epoxy repairs. Design principles were also established for these repairs under buckling.

Adhesively-bonded repair proposal for wood members damaged by horizontal shear using carbon-epoxy patches

In this work, a repair technique with adhesively bonded carbon-epoxy patches is proposed for wood members damaged by horizontal shear and under bending loads. This damage is characterized by horizontal crack growth near the neutral plane of the wood beam, normally originating from checks and shakes. The repair consists of adhesively bonded carbon-epoxy patches on the vertical side faces of the beam at the cracked region to block sliding between the beam arms. An experimental and numerical parametric analysis was performed on the patch length. The numerical analysis used the finite element method (FEM) and cohesive zone models (CZMs), with an inverse modelling technique for the characterization of the adhesive layer. Trapezoidal cohesive laws in each pure mode were used to account for the ductility of the adhesive used. To fully reproduce the tests, horizontal damage propagation within the wood beam was also simulated. A good correlation with the experiments was found. Regarding the effectiveness of the repair, for the conditions selected for this work, a full strength recovery was achieved for the bigger value of patch length tested.

The influence of the boundary conditions on low-velocity impact composite damage

The objective of this work was to study the influence of the boundary conditions on low-velocity impact behaviour of carbon-epoxy composite plates. Experimental work and numerical analysis were performed on [04,904]s laminates. The influence of different boundary conditions on the impacted plates was analysed considering rectangular and square plates. The X-radiography was used as a non-destructive technique to evaluate the internal damage caused by impact loading. A three-dimensional numerical analysis was also performed considering progressive damage modelling. The model includes three-dimensional solid elements and interface finite elements including a cohesive mixed-mode damage model, which allows simulating delamination between different oriented layers. It was verified that plate’s boundary conditions have influence on the delaminated area. Good agreement between experimental and numerical analysis for shape, orientation and size of the delamination was obtained.

A New Approach in the Design of Air Stripping Columns for the Treatment of Groundwater Contaminated With Volatile Organic Compounds

Volatile organic compounds are a common source of groundwater contamination that can be easily removed by air stripping in columns with random packing and using a counter-current flow between the phases. This work proposes a new methodology for column design for any type of packing and contaminant which avoids the necessity of an arbitrary chosen diameter. It also avoids the employment of the usual graphical Eckert correlations for pressure drop. The hydraulic features are previously chosen as a project criterion. The design procedure was translated into a convenient algorithm in C++ language. A column was built in order to test the design, the theoretical steady-state and dynamic behaviour. The experiments were conducted using a solution of chloroform in distilled water. The results allowed for a correction in the theoretical global mass transfer coefficient previously estimated by the Onda correlations, which depend on several parameters that are not easy to control in experiments. For best describe the column behaviour in stationary and dynamic conditions, an original mathematical model was developed. It consists in a system of two partial non linear differential equations (distributed parameters). Nevertheless, when flows are steady, the system became linear, although there is not an evident solution in analytical terms. In steady state the resulting ODE can be solved by analytical methods, and in dynamic state the discretization of the PDE by finite differences allows for the overcoming of this difficulty. To estimate the contaminant concentrations in both phases in the column, a numerical algorithm was used. The high number of resulting algebraic equations and the impossibility of generating a recursive procedure did not allow the construction of a generalized programme. But an iterative procedure developed in an electronic worksheet allowed for the simulation. The solution is stable only for similar discretizations values. If different values for time/space discretization parameters are used, the solution easily becomes unstable. The system dynamic behaviour was simulated for the common liquid phase perturbations: step, impulse, rectangular pulse and sinusoidal. The final results do not configure strange or non-predictable behaviours.

Multidimensional scaling visualization of earthquake phenomena

Earthquakes are associated with negative events, such as large number of casualties, destruction of buildings and infrastructures, or emergence of tsunamis. In this paper, we apply the Multidimensional Scaling (MDS) analysis to earthquake data. MDS is a set of techniques that produce spatial or geometric representations of complex objects, such that, objects perceived to be similar/distinct in some sense are placed nearby/distant on the MDS maps. The interpretation of the charts is based on the resulting clusters since MDS produces a different locus for each similarity measure. In this study, over three million seismic occurrences, covering the period from January 1, 1904 up to March 14, 2012 are analyzed. The events, characterized by their magnitude and spatiotemporal distributions, are divided into groups, either according to the Flinn–Engdahl seismic regions of Earth or using a rectangular grid based in latitude and longitude coordinates. Space-time and Space-frequency correlation indices are proposed to quantify the similarities among events. MDS has the advantage of avoiding sensitivity to the non-uniform spatial distribution of seismic data, resulting from poorly instrumented areas, and is well suited for accessing dynamics of complex systems. MDS maps are proven as an intuitive and useful visual representation of the complex relationships that are present among seismic events, which may not be perceived on traditional geographic maps. Therefore, MDS constitutes a valid alternative to classic visualization tools, for understanding the global behavior of earthquakes.

Strap repairs using embedded patches: numerical analysis and experimental results

Adhesively bonded repairs offer an attractive option for repair of aluminium structures, compared to more traditional methods such as fastening or welding. The single-strap (SS) and double-strap (DS) repairs are very straightforward to execute but stresses in the adhesive layer peak at the overlap ends. The DS repair requires both sides of the damaged structures to be reachable for repair, which is often not possible. In strap repairs, with the patches bonded at the outer surfaces, some limitations emerge such as the weight, aerodynamics and aesthetics. To minimize these effects, SS and DS repairs with embedded patches were evaluated in this work, such that the patches are flush with the adherends. For this purpose, in this work standard SS and DS repairs, and also with the patches embedded in the adherends, were tested under tension to allow the optimization of some repair variables such as the overlap length (LO) and type of adhesive, thus allowing the maximization of the repair strength. The effect of embedding the patch/patches on the fracture modes and failure loads was compared with finite elements (FE) analysis. The FE analysis was performed in ABAQUS® and cohesive zone modelling was used for the simulation of damage onset and growth in the adhesive layer. The comparison with the test data revealed an accurate prediction for all kinds of joints and provided some principles regarding this technique.