Optimization of the Ion Source-Mass Spectrometry Parameters in Non-Steroidal Anti-Inflammatory and Analgesic Pharmaceuticals Analysis by a Design of Experiments Approach

The flow rates of drying and nebulizing gas, heat block and desolvation line temperatures and interface voltage are potential electrospray ionization parameters as they may enhance sensitivity of the mass spectrometer. The conditions that give higher sensitivity of 13 pharmaceuticals were explored. First, Plackett-Burman design was implemented to screen significant factors, and it was concluded that interface voltage and nebulizing gas flow were the only factors that influence the intensity signal for all pharmaceuticals. This fractionated factorial design was projected to set a full 2(2) factorial design with center points. The lack-of-fit test proved to be significant. Then, a central composite face-centered design was conducted. Finally, a stepwise multiple linear regression and subsequently an optimization problem solving were carried out. Two main drug clusters were found concerning the signal intensities of all runs of the augmented factorial design. p-Aminophenol, salicylic acid, and nimesulide constitute one cluster as a result of showing much higher sensitivity than the remaining drugs. The other cluster is more homogeneous with some sub-clusters comprising one pharmaceutical and its respective metabolite. It was observed that instrumental signal increased when both significant factors increased with maximum signal occurring when both codified factors are set at level +1. It was also found that, for most of the pharmaceuticals, interface voltage influences the intensity of the instrument more than the nebulizing gas flowrate. The only exceptions refer to nimesulide where the relative importance of the factors is reversed and still salicylic acid where both factors equally influence the instrumental signal. Graphical Abstract ᅟ.

Impact of different moodle course designs on students? Performance

This work describes the impact of different teachers’ approaches in using Moodle, for supporting their courses, at the Polytechnic of Porto - School of Engineering. The study covers five different courses, from different degrees and different years, and includes a number of Moodle resources especially supporting laboratory classes. These and other active resources are particularly analyzed in order to evaluate students’ adherence to them. One particular course includes a number of remote experiments, made available through VISIR (Virtual Instrument Systems in Reality) and directly accessible through links included in the Moodle course page. The collected data have been correlated with students’ classifications in the lab component and in the exam, each one weighting 50% of their final marks. This analysis benefited from the existence of different teachers’ approaches, which resulted in a diversity of Moodle-supported environments. Conclusions point to the existence of a positive correlation factor between the number of Moodle accesses and the final exam grade, although the quality of the resources made available by the teachers seems to be preponderant over its quantity. In addition, different students perspectives were found regarding active resources: while some seem to encourage students to participate (for instance online quiz or online reports), others, more demanding, are unable to stimulate the majority of them.

Student performance analysis under different moodle course designs

This work extends a recent comparative study covering four different courses lectured at the Polytechnic of Porto - School of Engineering, in respect to the usage of a particular Learning Management System, i.e. Moodle, and its impact on students' results. A fifth course, which includes a number of resources especially supporting laboratory classes, is now added to the analysis. This particular course includes a number of remote experiments, made available through VISIR (Virtual Instrument Systems in Reality) and directly accessible through links included in the Moodle course page. We have analyzed the students' behavior in following these links and in effectively running experiments in VISIR (and also using other lab related resources, in Moodle). This data have been correlated with students' classifications in the lab component and in the exam, each one weighting 50% of their final marks. We aimed to compare students' performance in a richly Moodle-supported environment (with lab component) and in a poorly Moodle-supported environment (with only theoretical component). This question followed from conclusions drawn in the above referred comparative study, where it was shown that even though a positive correlation factor existed between the number of Moodle accesses and the final exam grade obtained by each student, its explanation behind was not straightforward, as the quality of the resources was preponderant over its quantity.

O empreendedorismo como fator dinamizador da competitividade regional: o papel do financiamento

Dissertação de Mestrado em Finanças Empresariais

Avaliação de compostos halogenados em água e ar de piscinas

A procura de piscinas para a prática de atividades desportivas, recreativas e/ou terapêuticas tem sofrido um aumento gradual ao longo do tempo. No entanto, nas piscinas existem vários perigos associados à sua utilização. Relativamente aos perigos químicos, a utilização de desinfetantes à base de cloro, bromo ou compostos derivados vai, por um lado, inativar microrganismos patogénicos mas, por outro, dar origem a subprodutos ao reagir com compostos orgânicos presentes na água. Os trihalometanos são um exemplo de subprodutos que se podem formar e, entre os compostos principais, estão o clorofórmio (TCM), bromodiclorometano (BDCM), clorodibromometano (CDBM) e bromofórmio (TBM). Este trabalho teve como objetivo o desenvolvimento de uma metodologia analítica para a determinação de trihalometanos em água e ar de piscinas e a sua aplicação a um conjunto de amostras. Para a análise dos compostos, foi utilizada a microextração em fase sólida no espaço de cabeça (HS-SPME) com posterior quantificação dos compostos por cromatografia gasosa com detetor de captura eletrónica (GC-ECD). Foi realizada uma otimização das condições de extração dos compostos em estudo em amostras de água, através da realização de dois planeamentos experimentais. As condições ótimas são assim obtidas para uma temperatura de extração de 45ºC, um tempo de extração de 25 min e um tempo de dessorção de 5 min. Foram analisadas amostras de águas de piscina cedidas pelo Centro de Estudos de Águas, sendo avaliada a aplicação da técnica HS-SPME e o efeito de matriz. O modo como se manuseiam as soluções que contêm os compostos em estudo influencia os resultados devido ao facto destes serem bastante voláteis. Concluiu-se também que existe efeito de matriz, logo a concentração das amostras deverá ser determinada através do método de adição de padrão. A caraterização da água de piscinas interiores permitiu conhecer a concentração de trihalometanos (THMs). Foram obtidas concentrações de TCM entre 4,5 e 406,5 μg/L sendo que apenas 4 das 27 amostras analisadas ultrapassam o valor limite imposto pelo Decreto-Lei nº306/2007 (100 μg/L) no que diz respeito a águas de consumo humano e que é normalmente utilizado como valor indicativo para a qualidade das águas de piscina. Relativamente à concentração obtida no ar de uma piscina interior, foi detetada uma concentração média de 224 μg/m3 de TCM, valor muito abaixo dos 10000 μg/m3 impostos pelo Decreto-lei nº24/2012, como valor limite para exposição profissional a agentes químicos.

Run-time monitoring approach for the shark kernel

Typically common embedded systems are designed with high resource constraints. Static designs are often chosen to address very specific use cases. On contrast, a dynamic design must be used if the system must supply a real-time service where the input may contain factors of indeterminism. Thus, adding new functionality on these systems is often accomplished by higher development time, tests and costs, since new functionality push the system complexity and dynamics to a higher level. Usually, these systems have to adapt themselves to evolving requirements and changing service requests. In this perspective, run-time monitoring of the system behaviour becomes an important requirement, allowing to dynamically capturing the actual scheduling progress and resource utilization. For this to succeed, operating systems need to expose their internal behaviour and state, making it available to the external applications, usually using a run-time monitoring mechanism. However, such mechanism can impose a burden in the system itself if not wisely used. In this paper we explore this problem and propose a framework, which is intended to provide this run-time mechanism whilst achieving code separation, run-time efficiency and flexibility for the final developer.

Full analysis of suspension geometry and chassis performance of Formula Student racing car

Formula Student events gather engineering students, who compete, designing, building and racing single-seater cars. The team of ISEP is working on its first car that soon will take part in this competition. This work aims to analyze the current design’s chassis, focusing on suspension geometry and frame’s performance. After analyzing results of the tests planned suggestions, that can be taken into consideration during design process of next cars will be presented. As the car has not been tested yet this work can also be helpful to explain its performance on the track later.

Convergence of Smart Grid ICT architectures for the last mile

The evolution of the electrical grid into a smart grid, allowing user production, storage and exchange of energy, remote control of appliances, and in general optimizations over how the energy is managed and consumed, is also an evolution into a complex Information and Communication Technology (ICT) system. With the goal of promoting an integrated and interoperable smart grid, a number of organizations all over the world started uncoordinated standardization activities, which caused the emergence of a large number of incompatible architectures and standards. There are now new standardization activities which have the goal of organizing existing standards and produce best practices to choose the right approach(es) to be employed in specific smart grid designs. This paper follows the lead of NIST and ETSI/CEN/CENELEC approaches in trying to provide taxonomy of existing solutions; our contribution reviews and relates current ICT state-of-the-art, with the objective of forecasting future trends based on the orientation of current efforts and on relationships between them. The resulting taxonomy provides guidelines for further studies of the architectures, and highlights how the standards in the last mile of the smart grid are converging to common solutions to improve ICT infrastructure interoperability.

Energy Harvesting for Autonomous Underwater Vehicles

In this study, energy production for autonomous underwater vehicles is investigated. This project is part of a bigger project called TURTLE. The autonomous vehicles perform oceanic researches at seabed for which they are intended to be kept operational underwater for several months. In order to ful l a long-term underwater condition, powerful batteries are combined with \micro- scale" energy production on the spot. This work tends to develop a system that generates power up to a maximum of 30 W. Latter energy harvesting structure consists basically of a turbine combined with a generator and low-power electronics to adjust the achieved voltage to a required battery charger voltage. Every component is examined separately hence an optimum can be de ned for all, and subsequently also an overall optimum. Di erent design parameters as e.g. number of blades, solidity ratio and cross-section area are compared for di erent turbines, in order to see what is the most feasible type. Further, a generator is chosen by studying how ux distributions might be adjusted to low velocities, and how cogging torque can be excluded by adapted designs. Low-power electronics are con gured in order to convert and stabilize heavily varying three-phase voltages to a constant, recti ed voltage which is usable for battery storage. Clearly, di erent component parameters as maximum power and torque are matched here to increase the overall power generation. Furthermore an overall maximum power is set up for achieving a maximum power ow at load side. Due to among others typical low velocities of about 0.1 to 0.5 m/s, and constructing limits of the prototype, the vast range of components is restricted to only a few that could be used. Hence, a helical turbine is combined in a direct drive mode to a coreless-stator axial- ux permanent-magnet generator, from which the output voltage is adjusted subsequently by a recti er, impedance matching unit, upconverter circuit and an overall control unit to regulate di erent component parameters. All these electronics are combined in a closed-loop design to involve positive feedback signals. Furthermore a theoretical con guration for the TURTLE vehicle is described in this work and a solution is proposed that might be implemented, for which several design tests are performable in a future study.

Effects of self-administered exercises based on Tuina techniques on musculoskeletal disorders of professional orchestra musicians: a randomized controlled trial

Background Musicians are frequently affected by playing-related musculoskeletal disorders (PRMD). Common solutions used by Western medicine to treat musculoskeletal pain include rehabilitation programs and drugs, but their results are sometimes disappointing. Objective To study the effects of self-administered exercises based on Tuina techniques on the pain intensity caused by PRMD of professional orchestra musicians, using numeric visual scale (NVS). Design, setting, participants and interventions We performed a prospective, controlled, single-blinded, randomized study with musicians suffering from PRMD. Participating musicians were randomly distributed into the experimental (n = 39) and the control (n = 30) groups. After an individual diagnostic assessment, specific Tuina self-administered exercises were developed and taught to the participants. Musicians were instructed to repeat the exercises every day for 3 weeks. Main outcome measures Pain intensity was measured by NVS before the intervention and after 1, 3, 5, 10, 15 and 20 d of treatment. The procedure was the same for the control group, however the Tuina exercises were executed in points away from the commonly-used acupuncture points. Results In the treatment group, but not the control group, pain intensity was significantly reduced on days 1, 3, 5, 10, 15 and 20. Conclusion The results obtained are consistent with the hypothesis that self-administered exercises based on Tuina techniques could help professional musicians controlling the pain caused by PRMD. Although our results are very promising, further studies are needed employing a larger sample size and double blinding designs.

Immediate effects of Tuina techniques on working-related musculoskeletal disorder of professional orchestra musicians

BACKGROUND: Musicians are a prone group to suffer from working-related musculoskeletal disorder (WRMD). Conventional solutions to control musculoskeletal pain include pharmacological treatment and rehabilitation programs but their efficiency is sometimes disappointing. OBJECTIVE: The aim of this research is to study the immediate effects of Tuina techniques on WRMD of professional orchestra musicians from the north of Portugal. DESIGN, SETTING, PARTICIPANTS AND INTERVENTIONS: We performed a prospective, controlled, single-blinded, randomized study. Professional orchestra musicians with a diagnosis of WRMD were randomly distributed into the experimental group (n=39) and the control group (n=30). During an individual interview, Chinese diagnosis took place and treatment points were chosen. Real acupoints were treated by Tuina techniques into the experimental group and non-specific skin points were treated into the control group. Pain was measured by verbal numerical scale before and immediately after intervention. RESULTS: After one treatment session, pain was reduced in 91.8% of the cases for the experimental group and 7.9% for the control group. CONCLUSION: Although results showed that Tuina techniques are effectively reducing WRMD in professional orchestra musicians of the north of Portugal, further investigations with stronger measurements, double-blinding designs and bigger simple sizes are needed.

Perspetivas interdisciplinares na planificação didática de Línguas e Culturas Estrangeiras

O presente Relatório Final de Estágio concretiza-se num trabalho de reflexão crítica sobre as práticas realizadas como professora estagiária de Inglês e de Espanhol no âmbito das Unidades Curriculares de Prática Educativa I, II e III, do Curso de Mestrado em Ensino de Inglês e Francês ou Espanhol, da Escola Superior de Educação, do Instituto Politécnico do Porto. A problemática que se apresenta decorre da perspetiva de que o ensino e aprendizagem de uma língua estrangeira baseados na articulação entre disciplinas do currículo contribui para uma aprendizagem holística, desenvolvendo competências que permitem um entendimento geral e global dos fenómenos humanos proporcionando aos alunos a compreensão do saber escolar como um todo articulável, contribuindo para uma leitura lógica e completa da realidade. A sua concretização na sala de aula impõe que o professor planifique atividades e opte por estratégias de ensino e de aprendizagem diversificadas, onde convergem finalidades, conceitos e metodologias de diversas disciplinas do currículo. Assim, este trabalho descreve a planificação de práticas de ensino e aprendizagem de Inglês e Espanhol em articulação com os conteúdos e os objetivos da disciplina de Estudo do Meio no Primeiro Ciclo. A planificação de práticas de Inglês no Segundo Ciclo foi realizada em articulação com a disciplina de História e Geografia de Portugal, com base na metodologia de projeto. As opções adotadas na planificação didática são consideradas estratégicas para uma aprendizagem significativa. Palavras-chave: perspetiva interdisciplinar do ensino; planificação didática de línguas estrangeiras; compreensão integrada do saber escolar; aprendizagem por projeto

Modelação e dimensionamento de estruturas

O presente relatório refere-se ao trabalho desenvolvido durante o período de estágio curricular enquadrado no ciclo de estudos do Mestrado em Engenharia Civil do ISEP, Instituto Superior de Engenharia do Porto. O estágio desenvolveu-se ao longo de seis meses, desde Fevereiro até Julho de 2015, na empresa FASE S.A., em ambiente de gabinete, para a obtenção do grau de mestre em Engenharia Civil. Durante o período de estágio foram desenvolvidos projetos de estabilidade de estruturas metálicas e de betão armado, desde a fase de conceção, pré-dimensionamento, modelação numérica e análise de resultados, dimensionamento final, até à produção das peças desenhas e escritas constituintes de um projeto de estruturas. Foi possível analisar e dimensionar estruturas através de programas de cálculo automático e ferramentas de cálculo que serão referidas no presente relatório. Neste relatório será descrita pormenorizadamente a elaboração de um projeto em betão armado em todas as suas vertentes. Apresentam-se também as metodologias de cálculo empregues. No culminar, enunciam-se algumas conclusões de carácter geral decorrentes do trabalho desenvolvido.

Aplicação do FMEA na avaliação de risco de taludes e muros de contenção tradicionais em alvenaria de pedra

Ao longo das últimas décadas o município de Amarante tem-se deparado com inúmeros problemas de instabilidade de estruturas de suporte de terras, maioritariamente instabilidade de taludes artificiais, (escavação e/ou aterro) e muros de contenção tradicionais em alvenaria de pedra. A unidade técnica de projeto, ou UTP da Câmara Municipal de Amarante tem vindo a elaborar estudos, projetos e adjudicar as obras para repor a normalidade apos a instabilização desses elementos, contudo a frequência de ocorrência destes fenómenos e os recursos necessários para a sua resolução ultrapassam a capacidade desta unidade, levando a que muitos destes casos se arrastem durante anos antes de ser reposta a sua normalidade. Perante este panorama revelou-se necessário efetuar um estudo de forma a listar, avaliar e priorizar os vários casos de instabilidade existentes, para uma eficiente alocação dos recursos disponíveis. Esta análise pretende ainda identificar as principais causas de instabilidade destas estruturas, de forma a eliminar ou mitigar a ocorrência de futuros problemas semelhantes. Para o estudo destes elementos de contenção de terras adotou-se o método de análise de risco conhecido como FMEA, “Failure Modes and Effects Analysis” ou Analise dos Modos de Falha e Efeitos, com as adaptações necessárias de forma a maximizar a confiabilidade das avaliações mediante a especificidade dos casos a avaliar e realidade da instituição.