Friction losses of Newtonian and non-Newtonian fluids flowing in laminar regime in a helical coil

This study aimed to carry out experimental work to determine, for Newtonian and non-Newtonian fluids, the friction factor (fc) with simultaneous heat transfer, at constant wall temperature as boundary condition, in fully developed laminar flow inside a vertical helical coil. The Newtonian fluids studied were aqueous solutions of glycerol, 25%, 36%, 43%, 59% and 78% (w/w). The non-Newtonian fluids were aqueous solutions of carboxymethylcellulose (CMC), a polymer, with concentrations of 0.2%, 0.3%, 0.4% and 0.6% (w/w) and aqueous solutions of xanthan gum (XG), another polymer, with concentrations of 0.1% and 0.2% (w/w). According to the rheological study done, the polymer solutions had shear-thinning behavior and different values of viscoelasticity. The helical coil used has an internal diameter, curvature ratio, length and pitch, respectively: 0.00483 m, 0.0263, 5.0 m and 11.34 mm. It was concluded that the friction factors, with simultaneous heat transfer, for Newtonian fluids can be calculated using expressions from literature for isothermal flows. The friction factors for CMC and XG solutions are similar to those for Newtonian fluids when the Dean number, based in a generalized Reynolds number, is less than 80. For Dean numbers higher than 80, the friction factors of the CMC solutions are lower those of the XG solutions and of the Newtonian fluids. In this range the friction factors decrease with the increase of the viscometric component of the solution and increase for increasing elastic component. The change of behavior at Dean number 80, for Newtonian and non-Newtonian fluids, is in accordance with the study of Ali [4]. There is a change of behavior at Dean number 80, for Newtonian and non-Newtonian fluids, which is in according to previous studies. The data also showed that the use of the bulk temperature or of the film temperature to calculate the physical properties of the fluid has a residual effect in the friction factor values.

Influence of grease rheology on thrust ball bearings friction torque

The friction torque and the operating temperatures in a thrust ball bearing were measured for seven different types of greases, including three biodegradable greases having low toxicity. These friction torque tests were performed using a modified Four-Ball machine. Rheological evaluations of the lubricating greases were made using a rheometer. Bleed oils were extracted from the greases and the dynamic viscosities were measured. In order to compare the performance of the lubricant greases in terms of friction, the grease characteristics were related to experimental results, showing that the interaction between thickener and base oil have strong influences in the bearing friction torque.

Experimental measuring procedure for the friction torque in rolling bearings

The reduction of the power loss generated in mechanical transmissions and the use of low friction biodegradable lubricants has been attracting considerable attention in recent times. Therefore, it is necessary to develop methods to test and evaluate the performance of such lubricants and compare them with conventional ones. In this sense, a Four-Ball Machine was modified allowing the test of rolling bearings. A 51107 thrust ball bearing was used to test two different greases and the corresponding base oils. Friction torque and operating temperatures were continuously monitored to quantify the power loss and the heat evacuation for each lubricant tested. Copyright © 2010 John Wiley & Sons, Ltd.

Friction and wear in thrust ball bearings lubricated with biodegradable greases

Thrust ball bearings lubricated with several different types of grease, including three biodegradable low-toxicity greases, were tested in a modified four-ball machine in order to evaluate the bearing friction torque. At the end of each test, grease samples were obtained and analysed through ferrography, allowing the quantification and evaluation of the bearing wear. In order to compare the grease performance in terms of friction and wear, a correlation between the grease characteristics (base oil, bleed oil, thickener structure, and rheological parameters) and the experimental results was established.

Friction torque in grease lubricated thrust ball bearings

Thrust ball bearings lubricated with several different greases were tested on a modified Four-Ball Machine, where the Four-Ball arrangement was replaced by a bearing assembly. The friction torque and operating temperatures in a thrust ball bearing were measured during the tests. At the end of each test a grease sample was analyzed through ferrographic techniques in order to quantify and evaluate bearing wear. A rolling bearing friction torque model was used and the coefficient of friction in full film lubrication was determined for each grease, depending on the operating conditions. The experimental results obtained showed that grease formulation had a very significant influence on friction torque and operating temperature. The friction torque depends on the viscosity of the grease base oil, on its nature (mineral, ester, PAO, etc.), on the coefficient of friction in full film conditions, but also on the interaction between grease thickener and base oil, which affected contact replenishment and contact starvation, and thus influenced the friction torque.

Fractional describing function of systems with nonlinear friction

This paper studies the describing function (DF) of systems consisting in a mass subjected to nonlinear friction. The friction force is composed in three components namely, the viscous, the Coulomb and the static forces. The system dynamics is analyzed in the DF perspective revealing a fractional-order behaviour. The reliability of the DF method is evaluated through the signal harmonic content and the limit cycle prediction.

Fractional describing function of systems with Coulomb friction

This paper studies the describing function (DF) of systems constituted by a mass subjected to nonlinear friction. The friction force is decomposed into two components, namely, the viscous and the Coulomb friction. The system dynamics is analyzed in the DF perspective revealing a fractional-order behavior. The reliability of the DF method is evaluated through the signal harmonic contents.

Estudo de um equipamento de processamento de soldaduras por Friction Stir Welding

Este é um projeto I&D interno do INEGI, com as unidades DPS e LOME, que tem em vista a utilização de componentes disponíveis no INEGI para o estudo de um equipamento capaz de efetuar soldaduras por Friction Stir Welding. O equipamento já conta com controlo numérico para um sistema de três eixos e os respetivos motores, ficando assim encarregue de tirar o máximo proveito possível destes componentes. Este equipamento terá como finalidade munir o INEGI com um equipamento capaz de dar resposta a eventuais projetos externos/internos bem como para fins de investigação para a melhoria da qualidade do processo de soldadura. A conceção deste equipamento tem a particularidade das condições envolventes do processo nomeadamente os esforços desenvolvidos durante o processo de soldadura, em particular a força vertical (eixo da ferramenta) que é necessária fazer de forma a evitar a ascensão de material da junta de soldadura. A soldadura por Friction Stir Welding, é um processo de soldadura relativamente actual, desenvolvido em 1991 por Wayne Thomas pelo The Welding Institute que se sobrepõe aos métodos de soldadura convencionais, uma vez que não necessita de levar o/os materiais acima da sua temperatura de fusão, sendo um processo de soldadura no estado solido, o material não chega a fundir. Este processo consiste na utilização de uma ferramenta em rotação que que se desloca ao longo da junta de soldadura, que uma vez a fricção gerada entre a ferramenta e o material base gera calor que promove o aquecimento e quase fusão do material base. A ligação do material dá-se aquando a passagem da ferramenta na junta, misturando os materiais. Com o recurso a este método de fabrico é possível efetuar soldaduras com grande qualidade em materiais considerados de difícil soldabilidade pelos métodos convencionais, como por exemplo o Alumínio. Neste projecto foram estudadas varias soluções, contactados vários fornecedores e com o seu feedback foi desenvolvido o equipamento. Este projecto consiste essencialmente na análise estrutural e selecção de equipamentos. O equipamento final resultou de uma série de iterações e ideias de forma a optimizar toda estrutura para a magnitude dos esforços envolvidos, obtendo no final um equipamento capaz de cumprir os requisitos. No final prevêse um equipamento com a capacidade de suportar esforços verticais de 50

Estudo geológico e geotécnico de taludes rochosos em S. Pedro da Afurada (Vila Nova de Gaia): contributos para a avaliação da estabilidade estrutural

Mestrado em Engenharia Geotécnica e Geoambiente

Construção de um robô trepador com locomoção através de rodas e adesão através de meios magnéticos

Mestrado em Engenharia Electrotécnica e de Computadores

Dimensionamento de muros de suporte considerando diferentes metodologias de cálculo

A presente dissertação consiste em verificar a tendência do coeficiente de segurança quando se varia certos parâmetros (ângulo de atrito interno do terreno, inclinação do terrapleno no tardoz do muro e o ângulo que a massa de solo faz quando se comporta como parte integrante do muro numa situação limite) considerados no cálculo. Para atingir os objectivos anteriormente referidos, dividiu-se o trabalho em duas fases, a primeira fase teve como objectivo verificar qual a tendência do coeficiente de segurança quando sujeito à variação de dois parâmetros, o ângulo de atrito interno do terreno e a inclinação do terrapleno no tardoz do muro que varia de 5° até ao valr do ângulo de atrito interno do terreno. A segunda fase consiste em analisar qual a tendência do coeficiente de segurança quando sujeito à variação de três parâmetros, o ângulo de atrito interno do terreno, de 20° a 45°, a inclinação do terrapleno no tardoz do muro, de 10° até ao valor do ângulo de atrito interno do terreno, e o ângulo que a massa de solo faz quando se comporta como parte integrante do muro numa situação limite. Para ambas as situações efectuaram-se os respectivos cálculos quer pela Teoria de Rankine e quer pela Teoria de Mohr – Coulomb, havendo casos em que foi necessário conjugar estas duas Teorias.

Distributed active traction control system applied to the RoboCup middle size league

This work addresses the problem of traction control in mobile wheeled robots in the particular case of the RoboCup Middle Size League (MSL). The slip control problem is formulated using simple friction models for ISePorto Team robots with a differential wheel configuration. Traction was also characterized experimentally in the MSL scenario for relevant game events. This work proposes a hierarchical traction control architecture which relies in local slip detection and control at each wheel, with relevant information being relayed to a higher level responsible for global robot motion control. A dedicated one axis control embedded hardware subsystem allowing complex local control, high frequency current sensing and odometric information procession was developed. This local axis control board is integrated in a distributed system using CAN bus communications. The slipping observer was implemented in the axis control hardware nodes integrated in the ISePorto robots and was used to control and detect loss of for traction. %and to detect the ball in the kicking device. An external vision system was used to perform a qualitative analysis of the slip detection and observer performance results are presented.

Self-mated tribological systems based on multilayer micro/nanocrystalline CVD diamond coatings

The tribological response of multilayer micro/nanocrystalline diamond coatings grown by the hot filament CVD technique is investigated. These multigrade systems were tailored to comprise a starting microcrystalline diamond (MCD) layer with high adhesion to a silicon nitride (Si3N4) ceramic substrate, and a top nanocrystalline diamond (NCD) layer with reduced surface roughness. Tribological tests were carried out with a reciprocating sliding configuration without lubrication. Such composite coatings exhibit a superior critical load before delamination (130–200 N), when compared to the mono- (60–100 N) and bilayer coatings (110 N), considering ∼10 µm thick films. Regarding the friction behaviour, a short-lived initial high friction coefficient was followed by low friction regimes (friction coefficients between 0.02 and 0.09) as a result of the polished surfaces tailored by the tribological solicitation. Very mild to mild wear regimes (wear coefficient values between 4.1×10−8 and 7.7×10−7 mm3 N−1 m−1) governed the wear performance of the self-mated multilayer coatings when subjected to high-load short-term tests (60–200 N; 2 h; 86 m) and medium-load endurance tests (60 N; 16 h; 691 m).

Networked embedded systems for active flow control in aircraft

Aerodynamic drag is known to be one of the factors contributing more to increased aircraft fuel consumption. The primary source of skin friction drag during flight is the boundary layer separation. This is the layer of air moving smoothly in the immediate vicinity of the aircraft. In this paper we discuss a cyber-physical system approach able of performing an efficient suppression of the turbulent flow by using a dense sensing deployment to detect the low pressure region and a similarly dense deployment of actuators to manage the turbulent flow. With this concept, only the actuators in the vicinity of a separation layer are activated, minimizing power consumption and also the induced drag.

Low torque loss gears: austempered ductile iron versus carburized steel

Low-loss power transmission gears operate at lower temperature than conventional ones because their teeth geometry is optimized to reduce friction. The main objective of this work is to compare the operating stabilization temperature and efficiency of low-loss austempered ductile iron (ADI) and carburized steel gears. Three different low-loss tooth geometries were adopted (types 311, 411 and 611, all produced using standard 20° pressure angle tools) and corresponding steel and ADI gears were tested in a FZG machine. The results obtained showed that low-loss geometries had a significant influence on power loss, gears 611 generating lower power loss than gears 311. At low speeds (500 and 1000 rpm) and high torque ADI gears generated lower power loss than steel gears. However, at high speed and high torque (high input power and high stabilization temperature) steel gears had better efficiency.