Relatório de Estágio

A Prática Educativa Supervisionada representa, sem dúvida, a etapa mais aguardada pelos estudantes que se formam para serem professores, pois este é um momento recheado de expectativas e descobertas da profissionalidade docente. Por conseguinte, o presente relatório de estágio pretende espelhar o percurso evolutivo da mestranda ao longo dessa prática pedagógica. A passagem pelas escolas ficou marcada por uma postura crítica e reflexiva perante as opções pedagógicas tomadas, sendo que estas resultaram sempre de uma articulação entre os quadros teóricos e práticos de cada área disciplinar. A supervisão, processo crucial durante o estágio, é considerada pela professora estagiária como um momento de acompanhamento e orientação da ação educativa por parte dos supervisores institucionais. A par deste processo foi sempre visível um trabalho colaborativo com o par pedagógico e com os professores cooperantes, com o principal objetivo de atingir novos e melhores modos de agir, ancorando-se, assim, nos pilares da metodologia de investigação-ação. O trajeto construído pela formanda é o retrato de uma experiência de desenvolvimento pessoal e profissional, tendo, porém, a convicção de que, apesar de este relatório marcar o término de um ciclo de estudos inicial, há muito mais para aprender e construir.

Using remote labs to serve different teacher's needs a case study with VISIR and RemotElectLab

Remote Laboratories are an emergent technological and pedagogical tool at all education levels, and their widespread use is an important part of their own improvement and evolution. This paper describes several issues encountered on laboratorial classes, on higher education courses, when using remote laboratories based on PXI systems, either using the VISIR system or an alternate in-house solution. Three main issues are presented and explained, all reported by teachers that gave support to students use of remote laboratories. The first issue deals with the need to allow students to select the actual place where an ammeter is to be inserted on electric circuits, even incorrectly, therefore emulating real world difficulties. The second one deals with problems with timing when several measurements are required at short intervals, as in the discharge cycle of a capacitor. And the last issue deals with the use of a multimeter in DC mode when reading AC values, a use that collides with the lab settings. All scenarios are presented and discussed including the solution found for each case. The conclusion derived from the described work is that the remote laboratories area is an expanding field, where practical use leads to improvement and evolution of the available solutions, requiring a strict cooperation and information sharing between all actors, i.e. developers, teachers and students.

How to feel "in love" with Math - a MOOC experience

In the past few years we have witnessed the fast development of distance learning tools such as Open Educational Resources (OER) and Massive Open Online Courses (MOOCs). This paper presents the “Mathematics without STRESS” MOOC Project, which is a cooperation between four schools from the Polytechnic Institute of Oporto (IPP). The concepts of MOOC and their quickly growing popularity are presented and complemented by a discussion of some MOOC definitions. The process of the project development is demonstrated by focusing on used MOOC structure, as well as the several types of course materials produced. At last, is presented a short discussion about problems and challenges met throughout the project. It is also our goal to contribute for a change in the way as teaching and learning Mathematics is seen and practiced nowadays.

How to reduce energy consumption on pultrusion

The global warming due to high CO2 emission in the last years has made energy saving a global problem nowadays. However, manufacturing processes such as pultrusion necessarily needs heat for curing the resin. Then, the only option available is to apply all efforts to make the process even more efficient. Different heating systems have been used on pultrusion, however, the most widely used are the planar resistances. The main objective of this study is to develop another heating system and compares it with the former one. Thermography was used in spite of define the temperature profile along the die. FEA (finite element analysis) allows to understand how many energy is spend with the initial heating system. After this first approach, changes were done on the die in order to test the new heating system and to check possible quality problems on the product. Thus, this work allows to conclude that with the new heating system a significant reduction in the setup time is now possible and an energy reduction of about 57% was achieved.

Simulation of the magnetic induction vector of a magnetic core to be used in FFC NMR relaxometry

This paper is a contribution for the assessment and comparison of magnet properties based on magnetic field characteristics particularly concerning the magnetic induction uniformity in the air gaps. For this aim, a solver was developed and implemented to determine the magnetic field of a magnetic core to be used in Fast Field Cycling (FFC) Nuclear Magnetic Resonance (NMR) relaxometry. The electromagnetic field computation is based on a 2D finite-element method (FEM) using both the scalar and the vector potential formulation. Results for the magnetic field lines and the magnetic induction vector in the air gap are presented. The target magnetic induction is 0.2 T, which is a typical requirement of the FFC NMR technique, which can be achieved with a magnetic core based on permanent magnets or coils. In addition, this application requires high magnetic induction uniformity. To achieve this goal, a solution including superconducting pieces is analyzed. Results are compared with a different FEM program.