Como integrar as TIC em contexto didático das Artes explorando a distribuição EVTux na área do cinema de animação

Com a implementação do Plano Tecnológico da Educação e consequente apetrechamento das Escolas com recursos tecnológicos avançados, surge agora a necessidade de criar condições favoráveis para a efetiva integração das TIC no currículo, nomeadamente na área das Artes. Decorrente das características singulares desta área curricular, são muitas as ferramentas digitais que podemos utilizar em contexto educativo mobilizando-as para experiências de aprendizagem baseadas em projetos que integrem as tecnologias. Este é o caso do EVTux, uma distribuição livre de Linux que permite a criação efetiva de projetos de cinema de animação em contexto educativo com recurso às tecnologias, caso que agora se apresenta como exemplo neste artigo e que atualmente faz parte de uma síntese do trabalho que se integra no projeto europeu TACCLE2 no qual participamos.

Green production of zero-valent iron nanoparticles using tree leaf extracts

The interest in zero-valent iron nanoparticles has been increasing significantly since the development of a green production method in which extracts from natural products or wastes are used. However, this field of application is yet poorly studied and lacks knowledge that allows the full understanding of the production and application processes. The aim of the present work was to evaluate the viability of the utilization of several tree leaves to produce extracts which are capable of reducing iron(III) in aqueous solution to form nZVIs. The quality of the extracts was evaluated concerning their antioxidant capacity. The results show that: i) dried leaves produce extracts with higher antioxidant capacities than non-dried leaves, ii) the most favorable extraction conditions (temperature, contact time, and volume:mass ratio) were identified for each leaf, iii) with the aim of developing a green, but also low-cost,method waterwas chosen as solvent, iv) the extracts can be classified in three categories according to their antioxidant capacity (expressed as Fe(II) concentration): >40 mmol L−1; 20–40 mmol L−1; and 2–10 mmol L−1; with oak, pomegranate and green tea leaves producing the richest extracts, and v) TEManalysis proves that nZVIs (d=10–20 nm) can be produced using the tree leaf extracts.

Controllability results for impulsive mixed type functional integro-differential evolution equations with nonlocal conditions

In this paper, we establish the controllability for a class of abstract impulsive mixed-type functional integro-differential equations with finite delay in a Banach space. Some sufficient conditions for controllability are obtained by using the Mönch fixed point theorem via measures of noncompactness and semigroup theory. Particularly, we do not assume the compactness of the evolution system. An example is given to illustrate the effectiveness of our results.

The influence of the boundary conditions on low-velocity impact composite damage

The objective of this work was to study the influence of the boundary conditions on low-velocity impact behaviour of carbon-epoxy composite plates. Experimental work and numerical analysis were performed on [04,904]s laminates. The influence of different boundary conditions on the impacted plates was analysed considering rectangular and square plates. The X-radiography was used as a non-destructive technique to evaluate the internal damage caused by impact loading. A three-dimensional numerical analysis was also performed considering progressive damage modelling. The model includes three-dimensional solid elements and interface finite elements including a cohesive mixed-mode damage model, which allows simulating delamination between different oriented layers. It was verified that plate’s boundary conditions have influence on the delaminated area. Good agreement between experimental and numerical analysis for shape, orientation and size of the delamination was obtained.

Evaluation of tools and cutting conditions on carbon fibre reinforced laminates

The distinctive characteristics of carbon fibre reinforced plastics, like low weight or high specific strength, had broadened their use to new fields. Due to the need of assembly to structures, machining operations like drilling are frequent. In result of composites inhomogeneity, this operation can lead to different damages that reduce mechanical strength of the parts in the connection area. From these damages, delamination is the most severe. A proper choice of tool and cutting parameters can reduce delamination substantially. In this work the results obtained with five different tool geometries are compared. Conclusions show that the choice of an adequate drill can reduce thrust forces, thus delamination damage.

Eficiência energética, aplicação em edifícios de serviços: o caso do hospital do ICUF

Mestrado em Engenharia Electrotécnica – Sistemas Eléctricos de Energia

Numerical solution of a PDE system with non-linear steady state conditions that translates the air stripping pollutants removal

This work deals with the numerical simulation of air stripping process for the pre-treatment of groundwater used in human consumption. The model established in steady state presents an exponential solution that is used, together with the Tau Method, to get a spectral approach of the solution of the system of partial differential equations associated to the model in transient state.

Spectral solution for the air stripping pollutants removal dynamic model with non linear steady state conditions

This work deals with the numerical simulation of air stripping process for the pre-treatment of groundwater used in human consumption. The model established in steady state presents an exponential solution that is used, together with the Tau Method, to get a spectral approach of the solution of the system of partial differential equations associated to the model in transient state.

Impact of the Meteorology Conditions on the Particulate Matter Dispersion from an Industrial Complex into Urban and Suburban Areas

The aim of this work was to assess the influence of meteorological conditions on the dispersion of particulate matter from an industrial zone into urban and suburban areas. The particulate matter concentration was related to the most important meteorological variables such as wind direction, velocity and frequency. A coal-fired power plant was considered to be the main emission source with two stacks of 225 m height. A middle point between the two stacks was taken as the centre of two concentric circles with 6 and 20 km radius delimiting the sampling area. About 40 sampling collectors were placed within this area. Meteorological data was obtained from a portable meteorological station placed at approximately 1.7 km to SE from the stacks. Additional data was obtained from the electrical company that runs the coal power plant. These data covers the years from 2006 to the present. A detailed statistical analysis was performed to identify the most frequent meteorological conditions concerning mainly wind speed and direction. This analysis revealed that the most frequent wind blows from Northwest and North and the strongest winds blow from Northwest. Particulate matter deposition was obtained in two sampling campaigns carried out in summer and in spring. For the first campaign the monthly average flux deposition was 1.90 g/m2 and for the second campaign this value was 0.79 g/m2. Wind dispersion occurred predominantly from North to South, away from the nearest residential area, located at about 6 km to Northwest from the stacks. Nevertheless, the higher deposition fluxes occurred in the NW/N and NE/E quadrants. This study was conducted considering only the contribution of particulate matter from coal combustion, however, others sources may be present as well, such as road traffic. Additional chemical analyses and microanalysis are needed to identify the source linkage to flux deposition levels.

Optimization of HS-SPME analytical conditions using factorial design for trihalomethanes determination in swimming pool water samples

Trihalomethanes (THMs) are widely referred and studied as disinfection by-products (DBPs). The THMs that are most commonly detected are chloroform (TCM), bromodichloromethane (BDCM), chlorodibromomethane (CDBM), and bromoform (TBM). Several studies regarding the determination of THMs in swimming pool water and air samples have been published. This paper reviews the most recent work in this field, with a special focus on water and air sampling, sample preparation and analytical determination methods. An experimental study has been developed in order to optimize the headspace solid-phasemicroextraction (HS-SPME) conditions of TCM, BDCM, CDBM and TBM from water samples using a 23 factorial design. An extraction temperature of 45 °C, for 25min, and a desorption time of 5 min were found to be the best conditions. Analysis was performed by gas chromatography with an electron capture detector (GC-ECD). The method was successfully applied to a set of 27 swimming pool water samples collected in the Oporto area (Portugal). TCM was the only THM detected with levels between 4.5 and 406.5 μg L−1. Four of the samples exceeded the guideline value for total THMs in swimming pool water (100 μgL−1) indicated by the Portuguese Health Authority.

Siderophore Production by Bacillus megaterium: Effect of Growth Phase and Cultural Conditions

Siderophore production by Bacillus megaterium was detected, in an iron-deficient culture medium, during the exponential growth phase, prior to the sporulation, in the presence of glucose; these results suggested that the onset of siderophore production did not require glucose depletion and was not related with the sporulation. The siderophore production by B. megaterium was affected by the carbon source used. The growth on glycerol promoted the very high siderophore production (1,182 μmol g−1 dry weight biomass); the opposite effect was observed in the presence of mannose (251 μmol g−1 dry weight biomass). The growth in the presence of fructose, galactose, glucose, lactose, maltose or sucrose, originated similar concentrations of siderophore (546–842 μmol g−1 dry weight biomass). Aeration had a positive effect on the production of siderophore. Incubation of B. megaterium under static conditions delayed and reduced the growth and the production of siderophore, compared with the incubation in stirred conditions.

A physical packing sequence algorithm for the container loading problem with static mechanical equilibrium conditions

The container loading problem (CLP) is a combinatorial optimization problem for the spatial arrangement of cargo inside containers so as to maximize the usage of space. The algorithms for this problem are of limited practical applicability if real-world constraints are not considered, one of the most important of which is deemed to be stability. This paper addresses static stability, as opposed to dynamic stability, looking at the stability of the cargo during container loading. This paper proposes two algorithms. The first is a static stability algorithm based on static mechanical equilibrium conditions that can be used as a stability evaluation function embedded in CLP algorithms (e.g. constructive heuristics, metaheuristics). The second proposed algorithm is a physical packing sequence algorithm that, given a container loading arrangement, generates the actual sequence by which each box is placed inside the container, considering static stability and loading operation efficiency constraints.

Numerical analysis of the initial conditions in fractional systems

Fractional dynamics is a growing topic in theoretical and experimental scientific research. A classical problem is the initialization required by fractional operators. While the problem is clear from the mathematical point of view, it constitutes a challenge in applied sciences. This paper addresses the problem of initialization and its effect upon dynamical system simulation when adopting numerical approximations. The results are compatible with system dynamics and clarify the formulation of adequate values for the initial conditions in numerical simulations.

Avaliação do efeito da microfauna do tanque de arejamento no efluente final

O presente trabalho, efetuado na Estação de Tratamento de Águas Residuais do Freixo (ETAR do Freixo), decorreu durante um período de nove meses, (entre Dezembro de 2012 e Agosto de 2013), e teve como principais objetivos: - a observação microscópica e respetiva identificação dos organismos presentes nas lamas ativadas dos reatores biológicos da ETAR (incidindo nos protozoários, metazoários e bactérias filamentosas); - estabelecer a relação entre os organismos identificados/quantidade respetiva e a sedimentabilidade das lamas ativadas e sua influência no processo de depuração; - avaliar a variação das espécies identificadas com as alterações processuais. Para o efeito, a metodologia utilizada foi: - a colheita diária de amostras em vários pontos da ETAR; - a determinação dos parâmetros operacionais e caracterização das amostras recolhidas, tendo sido efetuadas 6039 análises físico-químicas, incluindo ao afluente à ETAR, ao afluente e ao conteúdo dos dois reatores biológicos, à corrente de recirculação de lamas e ao efluente; - a visualização diária microscópica ótica sem contraste de fase dos microrganismos presentes nos reatores biológicos; - a visualização microscópica ótica com contraste de fase da microfauna presente nos reatores biológicos, sendo efetuadas 16 identificações e quantificações dos protozoários presentes nas lamas ativadas dos dois reatores e 10 identificações e quantificações das bactérias filamentosas presentes nos dois reatores biológicos. O início do estudo ocorreu num período em que se começou a verificar um aumento excessivo de espumas nos decantadores secundários, resultando numa fraca sedimentabilidade das lamas e numa menor qualidade do efluente final. Na tentativa de reduzir a excessiva ascensão do manto de lamas que se verificou, foram efectuadas alterações operacionais, consistindo: - na alteração da razão de recirculação da decantação secundária para os reatores biológicos; - na introdução de um composto altamente concentrado em matéria orgânica na corrente de recirculação de lamas; - na alteração da extração de lamas biológicas. Verificou-se que as alterações processuais efetuadas foram muito eficazes na diminuição do manto de lamas da decantação secundária, bem como muito eficazes na qualidade do efluente final. Durante os meses de Fevereiro a Agosto fez-se o acompanhamento diário de todas as condições de operação de modo a manter e validar o procedimento de operação, o qual se considerou muito eficaz em termos de obtenção de uma água tratada de excelente qualidade. Durante o estudo efetuado, verificou-se que a população microbiológica existente nos dois reatores biológicos se manteve praticamente inalterada durante todo o período, sendo os móveis de fundo e os sésseis os grupos dominantes. Esta dominância traduziu-se na elevada qualidade do efluente final que se observou a partir do mês de Fevereiro, tendo dificultado o estudo de novas condições de operação, mas facilitando a validação do procedimento adotado. No que se refere às bactérias filamentosas, verificou-se que são diversas as espécies presentes nos reatores biológicos e que existem em grande abundância, sendo que o Tipo 0092 é claramente dominante. O excessivo crescimento deste tipo de bactérias mostrou ser o maior problema a nível microbiológico no processo de tratamento da instalação, tornando-se crítico no período de inverno em que a temperatura e os picos de pluviosidade se mostraram condições favoráveis ao seu desenvolvimento. Para além da temperatura outros fatores mostraram-se responsáveis pelo seu crescimento tais como a razão Alimento/Microrganismo (A/M), a idade das lamas, a carga mássica afluente e o teor de oxigénio dissolvido nos reatores biológicos. Pode-se concluir que apesar de não se trabalhar com os valores teóricos dos parâmetros microbiológicos e operacionais considerados ideais, a ETAR do Freixo, possui um tratamento bastante eficaz na remoção da carga orgânica, na remoção de nutrientes e na remoção de sólidos suspensos totais, apesar da não existência de uma etapa de afinação final como a filtração.