Photoluminescence and electrical study of fluctuating potentials in Cu2ZnSnS4-based thin films

In this work, we investigated structural, morphological, electrical, and optical properties from a set of Cu2ZnSnS4 thin films grown by sulfurization of metallic precursors deposited on soda lime glass substrates coated with or without molybdenum. X-ray diffraction and Raman spectroscopy measurements revealed the formation of single-phase Cu2ZnSnS4 thin films. A good crystallinity and grain compactness of the film was found by scanning electron microscopy. The grown films are poor in copper and rich in zinc, which is a composition close to that of the Cu2ZnSnS4 solar cells with best reported efficiency. Electrical conductivity and Hall effect measurements showed a high doping level and a strong compensation. The temperature dependence of the free hole concentration showed that the films are nondegenerate. Photoluminescence spectroscopy showed an asymmetric broadband emission. The experimental behavior with increasing excitation power or temperature cannot be explained by donor-acceptor pair transitions. A model of radiative recombination of an electron with a hole bound to an acceptor level, broadened by potential fluctuations of the valence-band edge, was proposed. An ionization energy for the acceptor level in the range 29–40 meV was estimated, and a value of 172 ±2 meV was obtained for the potential fluctuation in the valence-band edge.

A wireless sensor network platform for structural health monitoring: enabling accurate and synchronized measurements through COTS+custom-based design

Structural health monitoring has long been identified as a prominent application of Wireless Sensor Networks (WSNs), as traditional wired-based solutions present some inherent limitations such as installation/maintenance cost, scalability and visual impact. Nevertheless, there is a lack of ready-to-use and off-the-shelf WSN technologies that are able to fulfill some most demanding requirements of these applications, which can span from critical physical infrastructures (e.g. bridges, tunnels, mines, energy grid) to historical buildings or even industrial machinery and vehicles. Low-power and low-cost yet extremely sensitive and accurate accelerometer and signal acquisition hardware and stringent time synchronization of all sensors data are just examples of the requirements imposed by most of these applications. This paper presents a prototype system for health monitoring of civil engineering structures that has been jointly conceived by a team of civil, and electrical and computer engineers. It merges the benefits of standard and off-the-shelf (COTS) hardware and communication technologies with a minimum set of custom-designed signal acquisition hardware that is mandatory to fulfill all application requirements.

An experimental study on recycling and reuse of pultruded composite material wastes

Glass fibre-reinforced plastics (GFRP) have been considered inherently difficult to recycle due to both: cross-linked nature of thermoset resins, which cannot be remoulded, and complex composition of the composite itself. Presently, most of the GFRP waste is landfilled leading to negative environmental impacts and supplementary added costs. With an increasing awareness of environmental matters and the subsequent desire to save resources, recycling would convert an expensive waste disposal into a profitable reusable material. In this study, efforts were made in order to recycle grinded GFRP waste, proceeding from pultrusion production scrap, into new and sustainable composite materials. For this purpose, GFRP waste recyclates, were incorporated into polyester based mortars as fine aggregate and filler replacements at different load contents and particle size distributions. Potential recycling solution was assessed by mechanical behaviour of resultant GFRP waste modified polymer mortars. Results revealed that GFRP waste filled polymer mortars present improved flexural and compressive behavior over unmodified polyester based mortars, thus indicating the feasibility of the GFRP industrial waste reuse into concrete-polymer composite materials.

Aplicação da abordagem KAIZEN na produção de artigos de papelaria

No âmbito da unidade curricular Tese/Dissertação do 2ºano do Mestrado em Engenharia Eletrotécnica – Ramo Sistemas e Planeamento Industrial do Instituto Superior de Engenharia do Porto, o presente trabalho descreve o estágio curricular efetuado num projeto industrial de melhoria em parceria com o Kaizen Institute, uma empresa de consultoria operacional. Este projeto foi desenvolvido numa empresa de produção e redistribuição de artigos de papelaria e escritório, a Firmo AVS – Papeis e Papelaria,S.A.. O acordo efetuado entre o Kaizen Institute e a Firmo AVS foi o de promover e incutir a cultura da melhoria continua e da mudança de atitudes e comportamentos por parte dos colaboradores da Firmo, sendo que numa fase inicial o foco do projeto foi o departamento de produção de envelopes, designada por área piloto, expandindo-se posteriormente a metodologia Kaizen aos restantes departamentos. A realização deste projeto teve como objetivo a implementação de conceitos elementares de melhoria continua nomeadamente alguns pilares ou ferramentas do Total Flow Management (TFM) e do Kaizen Management System (KMS) na empresa Firmo, de forma a reduzir ou eliminar desperdícios, incremento do envolvimento dos colaboradores, melhoria da comunicação e trabalho em equipa, estandardização de processos produtivos, criação de normas de trabalho, utilização de ferramentas SMED para a redução de tempos improdutivos e aumento da produtividade. Várias foram as dificuldades presentes no terreno para a implementação destes objetivos mas com as diversas ferramentas e workshops realizados na organização, conseguiu-se o envolvimento de todos os colaboradores da organização e a obtenção de resultados satisfatórios nomeadamente ao nível da comunicação e trabalho em equipa, organização e limpeza dos postos de trabalho, standard work (normalização do trabalho), diminuição do lead time nos processos produtivos e consequente aumento de produtividade.