Using a cohesive damage model to predict the tensile behaviour of CFRP single-strap repairs

This work addresses both experimental and numerical analyses regarding the tensile behaviour of CFRP single-strap repairs. Two fundamental geometrical parameters were studied: overlap length and patch thickness. The numerical model used ABAQUS® software and a developed cohesive mixed-mode damage model adequate for ductile adhesives, and implemented within interface finite elements. Stress analyses and strength predictions were carried out. Experimental and numerical comparisons were performed on failure modes, failure load and equivalent stiffness of the repair. Good correlation was found between experimental and numerical results, showing that the proposed model can be successfully applied to bonded joints or repairs.

Single-lap joints of similar and dissimilar adherends bonded with an acrylic adhesive

In this study, the tensile strength of single-lap joints (SLJs) between similar and dissimilar adherends bonded with an acrylic adhesive was evaluated experimentally and numerically. The adherend materials included polyethylene (PE), polypropylene (PP), carbon-epoxy (CFRP), and glass-polyester (GFRP) composites. The following adherend combinations were tested: PE/PE, PE/PP, PE/CFRP, PE/GFRP, PP/PP, CFRP/CFRP, and GFRP/GFRP. One of the objectives of this work was to assess the influence of the adherends stiffness on the strength of the joints since it significantly affects the peel stresses magnitude in the adhesive layer. The experimental results were also used to validate a new mixed-mode cohesive damage model developed to simulate the adhesive layer. Thus, the experimental results were compared with numerical simulations performed in ABAQUS®, including a developed mixed-mode (I+II) cohesive damage model, based on the indirect use of fracture mechanics and implemented within interface finite elements. The cohesive laws present a trapezoidal shape with an increasing stress plateau, to reproduce the behaviour of the ductile adhesive used. A good agreement was found between the experimental and numerical results.

Experimental study on polyester based concretes filled with glass fibre reinforced plastic recyclates – a contribution to composite materials sustainability

The development and applications of thermoset polymeric composites, namely fibre reinforced plastics (FRP), have shifted in the last decades more and more into the mass market [1]. Despite of all advantages associated to FRP based products, the increasing production and consume also lead to an increasing amount of FRP wastes, either end-of-lifecycle products, or scrap and by-products generated by the manufacturing process itself. Whereas thermoplastic FRPs can be easily recycled, by remelting and remoulding, recyclability of thermosetting FRPs constitutes a more difficult task due to cross-linked nature of resin matrix. To date, most of the thermoset based FRP waste is being incinerated or landfilled, leading to negative environmental impacts and supplementary added costs to FRP producers and suppliers. This actual framework is putting increasing pressure on the industry to address the options available for FRP waste management, being an important driver for applied research undertaken cost efficient recycling methods. [1-2]. In spite of this, research on recycling solutions for thermoset composites is still at an elementary stage. Thermal and/or chemical recycling processes, with partial fibre recovering, have been investigated mostly for carbon fibre reinforced plastics (CFRP) due to inherent value of carbon fibre reinforcement; whereas for glass fibre reinforced plastics (GFRP), mechanical recycling, by means of milling and grinding processes, has been considered a more viable recycling method [1-2]. Though, at the moment, few solutions in the reuse of mechanically-recycled GFRP composites into valueadded products are being explored. Aiming filling this gap, in this study, a new waste management solution for thermoset GFRP based products was assessed. The mechanical recycling approach, with reduction of GFRP waste to powdered and fibrous materials was applied, and the potential added value of obtained recyclates was experimentally investigated as raw material for polyester based mortars. The use of a cementless concrete as host material for GFRP recyclates, instead of a conventional Portland cement based concrete, presents an important asset in avoiding the eventual incompatibility problems arisen from alkalis silica reaction between glass fibres and cementious binder matrix. Additionally, due to hermetic nature of resin binder, polymer based concretes present greater ability for incorporating recycled waste products [3]. Under this scope, different GFRP waste admixed polymer mortar (PM) formulations were analyzed varying the size grading and content of GFRP powder and fibre mix waste. Added value of potential recycling solution was assessed by means of flexural and compressive loading capacities of modified mortars with regard to waste-free polymer mortars.

Reforço de estruturas de betão armado com compósitos de fibra de carbono

O relatório resulta do estágio realizado na empresa Sika Brasil, no âmbito da Unidade Curricular de DIPRE do Mestrado de Engenharia Civil do Instituto Superior de Engenharia do Porto. A área de especialidade incidiu na recuperação e reforço de estruturas (Target Market Refurbishment), onde se deu a oportunidade de aprofundar conhecimentos em reforço estrutural através do sistema de reforço com compósitos de fibra de carbono (CFRP) colado exteriormente (EBR - Externally Bonded Reinforcement). O estágio realizado permitiu uma abordagem com a gama de produtos de recuperação e reforço da Sika Brasil, sendo que houve um foco muito grande nos produtos que respeitam ao reforço estrutural com compósitos de fibra de carbono. Este documento visa várias etapas do estágio, relacionadas diretamente com o reforço estrutural com CFRP. Foi feito um levantamento teórico das características dos compósitos de fibra de carbono, dando a conhecer os materiais envolvidos no sistema, as suas propriedades mecânicas e o seu âmbito de aplicação. No sentido de ter um diálogo profícuo com os projetistas e aplicadores de sistemas compósitos de fibra, foi realizada uma análise do procedimento de cálculo para o dimensionamento de reforço CFRP, à luz do Bulletin 14 fib:01 (2001), bem como uma análise da situação de incêndio para os sistemas compósitos. Consta neste documento uma análise feita entre os principais fornecedores de sistemas de CFRP no Brasil, baseando-se a mesma no conteúdo das fichas técnicas de produto relativas ao sistema de reforço EBR e respetiva comparação com a informação necessária para dimensionamento, de acordo com o Bulletin 14 fib:01 (2001). É relatado um reforço estrutural, como caso de estudo, tendo-se dado a oportunidade de se acompanhar desde a sua fase de projeto até à fase de execução. Por fim, este documento contém a simulação de dois programas da Sika para dimensionamento de reforço CFRP. A simulação foi feita para uma viga submetida a esforço de flexão, com as características geométricas e solicitações previamente definidas.