QoS em WIMAX – Análise e avaliação de módulos para simulação com o ns-2

Mestrado em Engenharia Electrotécnica e de Computadores

Photoluminescence and electrical study of fluctuating potentials in Cu2ZnSnS4-based thin films

In this work, we investigated structural, morphological, electrical, and optical properties from a set of Cu2ZnSnS4 thin films grown by sulfurization of metallic precursors deposited on soda lime glass substrates coated with or without molybdenum. X-ray diffraction and Raman spectroscopy measurements revealed the formation of single-phase Cu2ZnSnS4 thin films. A good crystallinity and grain compactness of the film was found by scanning electron microscopy. The grown films are poor in copper and rich in zinc, which is a composition close to that of the Cu2ZnSnS4 solar cells with best reported efficiency. Electrical conductivity and Hall effect measurements showed a high doping level and a strong compensation. The temperature dependence of the free hole concentration showed that the films are nondegenerate. Photoluminescence spectroscopy showed an asymmetric broadband emission. The experimental behavior with increasing excitation power or temperature cannot be explained by donor-acceptor pair transitions. A model of radiative recombination of an electron with a hole bound to an acceptor level, broadened by potential fluctuations of the valence-band edge, was proposed. An ionization energy for the acceptor level in the range 29–40 meV was estimated, and a value of 172 ±2 meV was obtained for the potential fluctuation in the valence-band edge.

Comparative study about heating systems for pultrusion process

Different heating systems have been used in pultrusion, where the most widely used heaters are planar resistances. The primary objective of this study was to develop an improved heating system and compare its performance with that of a system with planar resistances. In this study, thermography was used to better understand the temperature profile along the die. Finite element analysis was performed to determine the amount of energy consumed by the heating systems. Improvements were made to the die to test the new heating system, and it was found that the new system reduced the setup time and energy consumption by approximately 57%.

A fractional approach for the motion planning of redundant and hyper-redundant manipulators

The trajectory planning of redundant robots through the pseudoinverse control leads to undesirable drift in the joint space. This paper presents a new technique to solve the inverse kinematics problem of redundant manipulators, which uses a fractional differential of order α to control the joint positions. Two performance measures are defined to examine the strength and weakness of the proposed method. The positional error index measures the precision of the manipulator's end-effector at the target position. The repeatability performance index is adopted to evaluate if the joint positions are repetitive when the manipulator execute repetitive trajectories in the operational workspace. Redundant and hyper-redundant planar manipulators reveal that it is possible to choose in a large range of possible values of α in order to get repetitive trajectories in the joint space.

An evolutionary approach for the motion planning of redundant and hyper-redundant manipulators

The trajectory planning of redundant robots is an important area of research and efficient optimization algorithms are needed. The pseudoinverse control is not repeatable, causing drift in joint space which is undesirable for physical control. This paper presents a new technique that combines the closed-loop pseudoinverse method with genetic algorithms, leading to an optimization criterion for repeatable control of redundant manipulators, and avoiding the joint angle drift problem. Computer simulations performed based on redundant and hyper-redundant planar manipulators show that, when the end-effector traces a closed path in the workspace, the robot returns to its initial configuration. The solution is repeatable for a workspace with and without obstacles in the sense that, after executing several cycles, the initial and final states of the manipulator are very close.

Optimising the energy consumption on pultrusion process

This study is based on a previous experimental work in which embedded cylindrical heaters were applied to a pultrusion machine die, and resultant energetic performance compared with that achieved with the former heating system based on planar resistances. The previous work allowed to conclude that the use of embedded resistances enhances significantly the energetic performance of pultrusion process, leading to 57% decrease of energy consumption. However, the aforementioned study was developed with basis on an existing pultrusion die, which only allowed a single relative position for the heaters. In the present work, new relative positions for the heaters were investigated in order to optimise heat distribution process and energy consumption. Finite Elements Analysis was applied as an efficient tool to identify the best relative position of the heaters into the die, taking into account the usual parameters involved in the process and the control system already tested in the previous study. The analysis was firstly developed based on eight cylindrical heaters located in four different location plans. In a second phase, in order to refine the results, a new approach was adopted using sixteen heaters with the same total power. Final results allow to conclude that the correct positioning of the heaters can contribute to about 10% of energy consumption reduction, decreasing the production costs and leading to a better eco-efficiency of pultrusion process.

Saving energy in the GFRP pultrusion process

This study addresses to the optimization of pultrusion manufacturing process from the energy-consumption point of view. The die heating system of external platen heaters commonly used in the pultrusion machines is one of the components that contribute the most to the high consumption of energy of pultrusion process. Hence, instead of the conventional multi-planar heaters, a new internal die heating system that leads to minor heat losses is proposed. The effect of the number and relative position of the embedded heaters along the die is also analysed towards the setting up of the optimum arrangement that minimizes both the energy rate and consumption. Simulation and optimization processes were greatly supported by Finite Element Analysis (FEA) and calibrated with basis on the temperature profile computed through thermography imaging techniques. The main outputs of this study allow to conclude that the use of embedded cylindrical resistances instead of external planar heaters leads to drastic reductions of both the power consumption and the warm-up periods of the die heating system. For the analysed die tool and process, savings on energy consumption up to 60% and warm-up period stages less than an half hour were attained with the new internal heating system. The improvements achieved allow reducing the power requirements on pultrusion process, and thus minimize industrial costs and contribute to a more sustainable pultrusion manufacturing industry.

How to reduce energy consumption on pultrusion

The global warming due to high CO2 emission in the last years has made energy saving a global problem nowadays. However, manufacturing processes such as pultrusion necessarily needs heat for curing the resin. Then, the only option available is to apply all efforts to make the process even more efficient. Different heating systems have been used on pultrusion, however, the most widely used are the planar resistances. The main objective of this study is to develop another heating system and compares it with the former one. Thermography was used in spite of define the temperature profile along the die. FEA (finite element analysis) allows to understand how many energy is spend with the initial heating system. After this first approach, changes were done on the die in order to test the new heating system and to check possible quality problems on the product. Thus, this work allows to conclude that with the new heating system a significant reduction in the setup time is now possible and an energy reduction of about 57% was achieved.

Optimizing the embedded heaters position in the pultrusion process using finite element analysis

This study is based on a previous experimental work in which embedded cylindrical heaters were applied to a pultrusion machine die, and resultant energetic performance compared with that achieved with the former heating system based on planar resistances. The previous work allowed to conclude that the use of embedded resistances enhances significantly the energetic performance of pultrusion process, leading to 57% decrease of energy consumption. However, the aforementioned study was developed with basis on an existing pultrusion die, which only allowed a single relative position for the heaters. In the present work, new relative positions for the heaters were investigated in order to optimize heat distribution process and energy consumption. Finite Elements Analysis was applied as an efficient tool to identify the best relative position of the heaters into the die, taking into account the usual parameters involved in the process and the control system already tested in the previous study. The analysis was firstly developed with basis on eight cylindrical heaters located in four different location plans. In a second phase, in order to refine the results, a new approach was adopted using sixteen heaters with the same total power. Final results allow to conclude that the correct positioning of the heaters can contribute to about 10% of energy consumption reduction, decreasing the production costs and leading to a better eco-efficiency of pultrusion process.

Calibração automática para sistema de localização Multi-câmara

Mestrado em Engenharia Electrotécnica e de Computadores - Sistemas Autónomos

Celorico Wireless

Mestrado em Engenharia Informática

Comunicações marítimas wi-fi usando a banda 5.8 ghz

Tendo em conta a popularidade que as comunicações Wi-Fi têm na atualidade em vários dispositivos como computadores portáteis, telemóveis ou tablets, sendo estes utilizados praticamente por qualquer pessoa, surgiu a ideia de utilizar esta tecnologia de baixo custo e isenta de licenciamento num cenário de comunicações marítimas. Neste contexto, esta permite fornecer o acesso à Internet em banda larga a grupos de embarcações, que atualmente recorrem a tecnologias de elevado custo (satélite) e/ou de banda estreita (rádios VHF). Com o acesso em banda larga, os proprietários poderão utilizar aplicações informáticas de interesse à atividade de negócio ou de lazer, até então só disponíveis junto à costa onde existe cobertura celular. Nesta tese pretende-se fazer um estudo teórico e prático sobre o alcance e respetivo desempenho de comunicações de banda larga em ambiente marítimo, utilizando parte da gama de frequências dos 5,8 GHz, isenta de licença, e a norma IEEE 802.11n. Para se utilizar equipamento produzido em massa a operar nessa gama, existem duas normas disponíveis, a IEEE 802.11a e a IEEE 802.11n. Optou-se pelo IEEE 802.11n pois os esquemas de codificação ao nível físico permitem débitos mais elevados e MIMO. Para a realização dos testes experimentais, foi necessário elaborar um protótipo de comunicação ponto a ponto, constituído por dois nós de comunicação. Um deles foi instalado numa embarcação de pesca em colaboração com a Associação Propeixe e o outro no Edifício Transparente, no Porto, em colaboração com a entidade gestora do edifício e a Associação Porto Digital. Tanto quanto se conhece é o primeiro teste de comunicações Wi-Fi realizado nestas condições a nível mundial. Os objetivos do trabalho foram atingidos. Foi possível estabelecer comunicações Wi-Fi na banda dos 5,8 GHz até cerca de 7 km com débito médio mínimo de 1 Mbit/s. O ambiente de testes desenvolvido e os resultados obtidos servirão de base para futuros trabalhos de investigação na área das comunicações marítimas.

Redes de terras associadas a estações de telecomunicações

As redes de terras são algo que atormenta muitas operadoras de telecomunicações. Quando o comum civil pensa que apenas existem antenas e que é importante a transmissão de dados porque naturalmente não lhes faz falta saber mais nada, as pessoas envolventes na construção de uma estação de telecomunicações têm preocupações não só com a parte de rádio e antenas, mas fundamentalmente com a parte de energia e de infra-estruturas. No desenvolvimento deste projecto, torna-se então importante perceber como as redes de terras são implementadas, como atingir valores satisfatórios para as operadoras, como realizar melhoria da rede de terras já existentes, implementar furos artesianos/valas e sobretudo como melhorar no futuro. Os materiais utilizados e o estudo prévio das condições do terreno onde a estação rádio-base é implementada nem sempre coincidem com os resultados desejados e que pensamos que seriam facilmente atingidos após implementação da torre. Neste projecto, vamos então acompanhar todos os processos, desde a legalização, construção, testes e finalmente a medição da resistência de terras final. Se os valores foram aceitáveis, óptimo para a operadora de telecomunicações e para a empresa responsável pela implementação. Caso os resultados estejam aquém das expectativas, é altura de selecionar os melhores e recorrendo a um conjunto de técnicas que garantam resultados e o menos dispêndio de dinheiro possível, vamos avançar para as melhorias. Os regimes de protecção das pessoas e da estação são bastante importantes. É importante também perceber as condições dos solos e saber simular com o programa ERICO que será fundamental para se efetuar uma comparação entre o teórico e o implementado praticamente. No fim, parte fulcral serão as medições finais, a relação preço-qualidade das melhorias implementadas, a análise dos resultados com argumentos válidos e o bom senso da operadora para aceitar ou rejeitar os trabalhos. Contrato é contrato, fazer mais e melhor é uma exigência constante.

SIR performance evaluation of MB-OFDM UWB system with residual timing offset

Signal-to-interference ratio (SIR) performance of a multiband orthogonal frequency division multiplexing ultra-wideband system with residual timing offset is investigated. To do so, an exact mathematical derivation of the SIR of this system is derived. It becomes obvious that, unlike a cyclic prefixing based system, a zero padding based system is sensitive to residual timing offset.

A Random Access Protocol incorporating Multi-Packet Reception, Retransmission Diversity and Successive Interference Cancellation

8th International Workshop on Multiple Access Communications (MACOM2015), Helsinki, Finland.