3 resultados para Bond strength (chemical)

em Instituto Politécnico do Porto, Portugal


Relevância:

100.00% 100.00%

Publicador:

Resumo:

The main aims of the present study are simultaneously to relate the brazing parameters with: (i) the correspondent interfacial microstructure, (ii) the resultant mechanical properties and (iii) the electrochemical degradation behaviour of AISI 316 stainless steel/alumina brazed joints. Filler metals on such as Ag–26.5Cu–3Ti and Ag–34.5Cu–1.5Ti were used to produce the joints. Three different brazing temperatures (850, 900 and 950 °C), keeping a constant holding time of 20 min, were tested. The objective was to understand the influence of the brazing temperature on the final microstructure and properties of the joints. The mechanical properties of the metal/ceramic (M/C) joints were assessed from bond strength tests carried out using a shear solicitation loading scheme. The fracture surfaces were studied both morphologically and structurally using scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS) and X-ray diffraction analysis (XRD). The degradation behaviour of the M/C joints was assessed by means of electrochemical techniques. It was found that using a Ag–26.5Cu–3Ti brazing alloy and a brazing temperature of 850 °C, produces the best results in terms of bond strength, 234 ± 18 MPa. The mechanical properties obtained could be explained on the basis of the different compounds identified on the fracture surfaces by XRD. On the other hand, the use of the Ag–34.5Cu–1.5Ti brazing alloy and a brazing temperature of 850 °C produces the best results in terms of corrosion rates (lower corrosion current density), 0.76 ± 0.21 μA cm−2. Nevertheless, the joints produced at 850 °C using a Ag–26.5Cu–3Ti brazing alloy present the best compromise between mechanical properties and degradation behaviour, 234 ± 18 MPa and 1.26 ± 0.58 μA cm−2, respectively. The role of Ti diffusion is fundamental in terms of the final value achieved for the M/C bond strength. On the contrary, the Ag and Cu distribution along the brazed interface seem to play the most relevant role in the metal/ceramic joints electrochemical performance.

Relevância:

90.00% 90.00%

Publicador:

Resumo:

Este trabalho pretende estabelecer uma relação entre o Work Index e algumas propriedades das rochas. Através da pesquisa bibliográfica foram identificadas varias propriedades com possível influência no valor do Work Index, das quais foram seleccionadas a massa volúmica aparente, a resistência à carga pontual, a composição química, a composição mineralógica e a abrasividade. Adicionalmente a porosidade aberta e resistência à compressão também foram analisadas. Assim foram analisadas 10 amostras de rocha, quatro de granitos, uma de quartzodiorito, uma de ardósia, uma de serpentinito, uma de calcário, uma de mármore e uma de sienito nefelínico, sobre as quais já eram conhecidos os valores de cinco das propriedades referidas previamente, tendo sido determinados os valores das ainda desconhecidas, resistência à carga pontual e a abrasividade que está representada através do resultado do ensaio capon. Devido à dificuldade de execução do ensaio de determinação do Work Index de Bond foram recolhidos dados bibliográficos de valores do Work Index para as amostras de rocha seleccionadas e adoptado o valor médio para cada uma. Os dados obtidos foram tratados estatisticamente através do método de análise de componentes principais assim como através de regressões lineares simples e múltiplas. A análise de componentes principais permitiu identificar várias propriedades da rocha com possível influência sobre o Work Index de entre as analisadas. Foi possível estabelecer uma relação entre o Work Index e quatro das propriedades seleccionadas, designadamente a porosidade aberta, a resistência à compressão, a resistência à carga pontual e a abrasividade.

Relevância:

30.00% 30.00%

Publicador:

Resumo:

Interest in polyethylene and polypropylene bonding has increased in the last years. However, adhesive joints with adherends which are of low surface energy and which are chemically inert present several difficulties. Generally, their high degree of chemical resistance to solvents and dissimilar solubility parameters limit the usefulness of solvent bonding as a viable assembly technique. One successful approach to adhesive bonding of these materials involves proper selection of surface pre-treatment prior to bonding. With the correct pre-treatment it is possible to glue these materials with one or more of several adhesives required by the applications involved. A second approach is the use of adhesives without surface pre-treatment, such as hot melts, high tack pressure-sensitive adhesives, solvent-based specialty adhesives and, more recently, structural acrylic adhesives as such 3M DP-8005® and Loctite 3030®. In this paper, the shear strengths of two acrylic adhesives were evaluated using the lap shear test method ASTM D3163 and the block shear test method ASTM D4501. Two different industrial polyolefins (polyethylene and polypropylene) were used for adherends. However, the focus of this study was to measure the shear strength of polyethylene joints with acrylic adhesives. The effect of abrasion was also studied. Some test specimens were manually abraded using 180 and 320 grade abrasive paper. An additional goal of this work was to examine the effect of temperature and moisture on mechanical strength of adhesive joints.