Soil remediation time to achieve clean-up goals I: influence of soil water content

The current models are not simple enough to allow a quick estimation of the remediation time. This work reports the development of an easy and relatively rapid procedure for the forecasting of the remediation time using vapour extraction. Sandy soils contaminated with cyclohexane and prepared with different water contents were studied. The remediation times estimated through the mathematical fitting of experimental results were compared with those of real soils. The main objectives were: (i) to predict, through a simple mathematical fitting, the remediation time of soils with water contents different from those used in the experiments; (ii) to analyse the influence of soil water content on the: (ii1) remediation time; (ii2) remediation efficiency; and (ii3) distribution of contaminants in the different phases present into the soil matrix after the remediation process. For sandy soils with negligible contents of clay and natural organic matter, artificially contaminated with cyclohexane before vapour extraction, it was concluded that (i) if the soil water content belonged to the range considered in the experiments with the prepared soils, then the remediation time of real soils of similar characteristics could be successfully predicted, with relative differences not higher than 10%, through a simple mathematical fitting of experimental results; (ii) increasing soil water content from 0% to 6% had the following consequences: (ii1) increased remediation time (1.8–4.9 h, respectively); (ii2) decreased remediation efficiency (99–97%, respectively); and (ii3) decreased the amount of contaminant adsorbed onto the soil and in the non-aqueous liquid phase, thus increasing the amount of contaminant in the aqueous and gaseous phases.

Soil remediation time to achieve clean-up goals II: influence of natural organic matter and water contents

This work reports a relatively rapid procedure for the forecasting of the remediation time (RT) of sandy soils contaminated with cyclohexane using vapour extraction. The RT estimated through the mathematical fitting of experimental results was compared with that of real soils. The main objectives were: (i) to predict the RT of soils with natural organic matter (NOM) and water contents different from those used in experiments; and (ii) to analyse the time and efficiency of remediation, and the distribution of contaminants into the soil matrix after the remediation process, according to the soil contents of: (ii1) NOM; and (ii2) water. For sandy soils with negligible clay contents, artificially contaminated with cyclohexane before vapour extraction, it was concluded that: (i) if the NOM and water contents belonged to the range of the prepared soils, the RT of real soils could be predicted with relative differences not higher than 12%; (ii1) the increase of NOM content from 0% to 7.5% increased the RT (1.8–13 h) and decreased the remediation efficiency (RE) (99–90%) and (ii2) the increase of soil water content from 0% to 6% increased the RT (1.8–4.9 h) and decreased the RE (99–97%). NOM increases the monolayer capacity leading to a higher sorption into the solid phase. Increasing of soil water content reduces the mass transfer coefficient between phases. Concluding, NOM and water contents influence negatively the remediation process, turning it less efficient and more time consuming, and consequently more expensive.

An embedded 1149.4 extension to support mixed-signal debugging

Debugging electronic circuits is traditionally done with bench equipment directly connected to the circuit under debug. In the digital domain, the difficulties associated with the direct physical access to circuit nodes led to the inclusion of resources providing support to that activity, first at the printed circuit level, and then at the integrated circuit level. The experience acquired with those solutions led to the emergence of dedicated infrastructures for debugging cores at the system-on-chip level. However, all these developments had a small impact in the analog and mixed-signal domain, where debugging still depends, to a large extent, on direct physical access to circuit nodes. As a consequence, when analog and mixed-signal circuits are integrated as cores inside a system-on-chip, the difficulties associated with debugging increase, which cause the time-to-market and the prototype verification costs to also increase. The present work considers the IEEE1149.4 infrastructure as a means to support the debugging of mixed-signal circuits, namely to access the circuit nodes and also an embedded debug mechanism named mixed-signal condition detector, necessary for watch-/breakpoints and real-time analysis operations. One of the main advantages associated with the proposed solution is the seamless migration to the system-on-chip level, as the access is done through electronic means, thus easing debugging operations at different hierarchical levels.

Using mobile device detection approaches to augment the accuracy of web delivery content

Recent studies of mobile Web trends show a continuous explosion of mobile-friendly content. However, the increasing number and heterogeneity of mobile devices poses several challenges for Web programmers who want to automatically get the delivery context and adapt the content to mobile devices. In this process, the devices detection phase assumes an important role where an inaccurate detection could result in a poor mobile experience for the enduser. In this paper we compare the most promising approaches for mobile device detection. Based on this study, we present an architecture for a system to detect and deliver uniform m-Learning content to students in a Higher School. We focus mainly on the devices capabilities repository manageable and accessible through an API. We detail the structure of the capabilities XML Schema that formalizes the data within the devices capabilities XML repository and the REST Web Service API for selecting the correspondent devices capabilities data according to a specific request. Finally, we validate our approach by presenting the access and usage statistics of the mobile web interface of the proposed system such as hits and new visitors, mobile platforms, average time on site and rejection rate.

Position paper on time and event-triggered communication services in the context of e-manufacturing

Modern factories are complex systems where advances in networking and information technologies are opening new ways towards higher efficiency. Such move is being driven by market rules with ever-increasing competition levels, in search for faster time-to-market, improved process yield, non-stop operations, flexible manufacturing and tighter supply-chain coupling. All these aims present a common requirement, i.e. a realtime flow of information, from the plant-floor up to the management, maintenance, suppliers and clients, to support accurate monitoring and control of the factory. This stresses the importance achieved by the communication infrastructure in modern manufacturing industry. This paper presents the authors view concerning the current trends in modern factory communication systems. It addresses the problems of seamlessly integrating different information flows with diverse requirements, mainly in terms of timeliness. In this aspect, the debate between event-triggered and time-triggered communication is revisited as well as the joint support for both types of traffic. Finally, a view of where factory communication systems are moving to is also presented, showing the impact of open and widely available technologies.

Adding local priority-based dispatching mechanisms to P-NET networks: a fixed priority approach

In this paper we address the real-time capabilities of P-NET, which is a multi-master fieldbus standard based on a virtual token passing scheme. We show how P-NET’s medium access control (MAC) protocol is able to guarantee a bounded access time to message requests. We then propose a model for implementing fixed prioritybased dispatching mechanisms at each master’s application level. In this way, we diminish the impact of the first-come-first-served (FCFS) policy that P-NET uses at the data link layer. The proposed model rises several issues well known within the real-time systems community: message release jitter; pre-run-time schedulability analysis in non pre-emptive contexts; non-independence of tasks at the application level. We identify these issues in the proposed model and show how results available for priority-based task dispatching can be adapted to encompass priority-based message dispatching in P-NET networks.

BANMAC: an opportunistic MAC protocol for reliable communications in body area networks

We consider reliable communications in Body Area Networks (BAN), where a set of nodes placed on human body are connected using wireless links. In order to keep the Specific Absorption Rate (SAR) as low as possible for health safety reasons, these networks operate in low transmit power regime, which however, is known to be error prone. It has been observed that the fluctuations of the Received Signal Strength (RSS) at the nodes of a BAN on a moving person show certain regularities and that the magnitude of these fluctuations are significant (5 - 20 dB). In this paper, we present BANMAC, a MAC protocol that monitors and predicts the channel fluctuations and schedules transmissions opportunistically when the RSS is likely to be higher. The MAC protocol is capable of providing differentiated service and resolves co-channel interference in the event of multiple co-located BANs in a vicinity. We report the design and implementation details of BANMAC integrated with the IEEE 802.15.4 protocol stack. We present experimental data which show that the packet loss rate (PLR) of BANMAC is significantly lower as compared to that of the IEEE 802.15.4 MAC. For comparable PLR, the power consumption of BANMAC is also significantly lower than that of the IEEE 802.15.4. For co-located networks, the convergence time to find a conflict-free channel allocation was approximately 1 s for the centralized coordination mechanism and was approximately 4 s for the distributed coordination mechanism.

Handling QoS dependencies in distributed cooperative real-time systems

Due to the growing complexity and adaptability requirements of real-time embedded systems, which often exhibit unrestricted inter-dependencies among supported services and user-imposed quality constraints, it is increasingly difficult to optimise the level of service of a dynamic task set within an useful and bounded time. This is even more difficult when intending to benefit from the full potential of an open distributed cooperating environment, where service characteristics are not known beforehand. This paper proposes an iterative refinement approach for a service’s QoS configuration taking into account services’ inter-dependencies and quality constraints, and trading off the achieved solution’s quality for the cost of computation. Extensive simulations demonstrate that the proposed anytime algorithm is able to quickly find a good initial solution and effectively optimises the rate at which the quality of the current solution improves as the algorithm is given more time to run. The added benefits of the proposed approach clearly surpass its reducedoverhead.

Recomendação de conteúdos multimédia

A quantidade e variedade de conteúdos multimédia actualmente disponíveis cons- tituem um desafio para os utilizadores dado que o espaço de procura e escolha de fontes e conteúdos excede o tempo e a capacidade de processamento dos utilizado- res. Este problema da selecção, em função do perfil do utilizador, de informação em grandes conjuntos heterogéneos de dados é complexo e requer ferramentas específicas. Os Sistemas de Recomendação surgem neste contexto e são capazes de sugerir ao utilizador itens que se coadunam com os seus gostos, interesses ou necessidades, i.e., o seu perfil, recorrendo a metodologias de inteligência artificial. O principal objectivo desta tese é demonstrar que é possível recomendar em tempo útil conteúdos multimédia a partir do perfil pessoal e social do utilizador, recorrendo exclusivamente a fontes públicas e heterogéneas de dados. Neste sen- tido, concebeu-se e desenvolveu-se um Sistema de Recomendação de conteúdos multimédia baseado no conteúdo, i.e., nas características dos itens, no historial e preferências pessoais e nas interacções sociais do utilizador. Os conteúdos mul- timédia recomendados, i.e., os itens sugeridos ao utilizador, são provenientes da estação televisiva britânica, British Broadcasting Corporation (BBC), e estão classificados de acordo com as categorias dos programas da BBC. O perfil do utilizador é construído levando em conta o historial, o contexto, as preferências pessoais e as actividades sociais. O YouTube é a fonte do histo- rial pessoal utilizada, permitindo simular a principal fonte deste tipo de dados - a Set-Top Box (STB). O historial do utilizador é constituído pelo conjunto de vídeos YouTube e programas da BBC vistos pelo utilizador. O conteúdo dos vídeos do YouTube está classificado segundo as categorias de vídeo do próprio YouTube, sendo efectuado o mapeamento para as categorias dos programas da BBC. A informação social, que é proveniente das redes sociais Facebook e Twit- ter, é recolhida através da plataforma Beancounter. As actividades sociais do utilizador obtidas são filtradas para extrair os filmes e séries que são, por sua vez, enriquecidos semanticamente através do recurso a repositórios abertos de dados interligados. Neste caso, os filmes e séries são classificados através dos géneros da IMDb e, posteriormente, mapeados para as categorias de programas da BBC. Por último, a informação do contexto e das preferências explícitas, através da classificação dos itens recomendados, do utilizador são também contempladas. O sistema desenvolvido efectua recomendações em tempo real baseado nas actividades das redes sociais Facebook e Twitter, no historial de vídeos Youtube e de programas da BBC vistos e preferências explícitas. Foram realizados testes com cinco utilizadores e o tempo médio de resposta do sistema para criar o conjunto inicial de recomendações foi 30 s. As recomendações personalizadas são geradas e actualizadas mediante pedido expresso do utilizador.

Virtual Communities of Practice: Design and Development of Support Platforms and Participation Fostering

Mestrado em Engenharia Informática - Área de Especialização em Sistemas Gráficos e Multimédia

Haemoglobin smart plastic antibody material tailored with charged binding sites on silica nanoparticles: its application as an ionophore in potentiometric transduction

This work uses surface imprinting to design a novel smart plastic antibodymaterial (SPAM) for Haemoglobin (Hb). Charged binding sites are described here for the first time to tailor plastic antibody nanostructures for a large size protein such as Hb. Its application to design small, portable and low cost potentiometric devices is presented. The SPAM material was obtained by linking Hb to silica nanoparticles and allowing its ionic interaction with charged vinyl monomers. A neutral polymeric matrix was created around these and the imprinted protein removed. Additional materials were designed in parallel acting as a control: a neutral imprinted material (NSPAM), obtained by removing the charged monomers from the procedure, and the Non-Imprinted (NI) versions of SPAM and NSPAM by removing the template. SEM analysis confirmed the surface modification of the silica nanoparticles. All materials were mixed with PVC/plasticizer and applied as selective membranes in potentiometric transduction. Electromotive force (emf) variations were detected only for selective membranes having a lipophilic anionic additive in the membrane. The presence of Hb inside these membranes was evident and confirmed by FTIR, optical microscopy and Raman spectroscopy. The best performance was found for SPAM-based selective membranes with an anionic lipophilic additive, at pH 5. The limits of detection were 43.8 mg mL 1 and linear responses were obtained down to 83.8 mg mL 1, with an average cationic slope of +40 mV per decade. Good selectivity was also observed against other coexisting biomolecules. The analytical application was conducted successfully, showing accurate and precise results.

Melhoria do Processo Produtivo da Pietec Através das Ferramentas Kaizen

Esta Tese de Mestrado foi realizada na empresa Pietec Cortiças S.A.. A empresa Pietec Cortiças S.A. é a unidade industrial responsável pela produção de rolhas técnicas de cortiça do Grupo Piedade. O objetivo desta tese prende-se com a melhoria do processo produtivo de uma das suas secções, a secção da Marcação. Esta secção é responsável pela marcação da superfície da rolha, pela aplicação do tratamento de superfície e pelo embalamento das rolhas. A otimização do processo da secção de Marcação, na qualidade de última secção do processo produtivo, permitirá à empresa obter vantagens competitivas. De forma a atingir o objetivo proposto, foi realizado um levantamento exaustivo do processo produtivo e das respetivas operações. Esta análise permitiu a identificação dos possíveis pontos de desperdício, a sua avaliação e a definição de possíveis melhorias que visam o aumento de produtividade e a redução do número de produtos não conformes. Uma vez identificados os pontos críticos do processo, procedeu-se à definição das ações de melhoria a implementar de forma a melhorar o processo produtivo. As ações tomadas assentam na filosofia Lean e nos seus princípios, utilizando-se algumas das ferramentas desta filosofia para concretizar os objetivos traçados. A ferramenta de análise Plan-Do-Check-Act (PDCA) foi a ferramenta base do projeto, acompanhando na elaboração do plano de ação, na implementação das ferramentas 5S e Single Minute Exchange of Die (SMED), na verificação dos resultados e no plano de manutenção das melhorias alcançadas. Após a implementação das medidas definidas no processo de marcação da superfície das rolhas, foi mensurada uma melhoria de 23 % no tempo médio de setup da máquina de marcação. Esta melhoria global foi alcançada através de intervenções no processo de vazamento do circuito da máquina de marcação, no procedimento de armazenamento dos moldes de marcação e na alteração dos mecanismos de ajuste da máquina de marcar e de orientar. No processo de embalamento das rolhas, as medidas implementadas produziram um aumento de 1,7 % no número de rolhas produzidas e uma redução do número de rolhas não conformes de 3,6 %. Os resultados obtidos no projeto demonstram que é possível continuar a melhorar o estado atual dos processos. Constatou-se ainda que, com a adoção de ferramentas de análise e de proposta de melhoria adequadas, é possível atuar sobre os processos e obter melhorias a curto prazo, sem que para isso seja necessário efetuar grandes investimentos.

Conceção e Análise de um Demonstrador para a Monitorização Estrutural

Os sistemas de monitorização de estruturas fornecem diversas vantagens, não só no que diz respeito à durabilidade da obra, ao aumento da segurança e do conhecimento relativamente ao comportamento das estruturas ao longo do tempo, à otimização do aspeto estrutural, bem como aos aspetos económicos do processo de construção e manutenção. A monitorização deve realizar-se durante a fase de construção e/ou de exploração da obra para permitir o registo integral do seu comportamento no meio externo. Deve efetuar-se de forma contínua e automática, executando intervenções de rotina para que se possa detetar precocemente sinais de alterações, respetivamente à segurança, integridade e desempenho funcional. Assim se poderá manter a estrutura dentro de parâmetros aceitáveis de segurança. Assim, na presente dissertação será concebido um demonstrador experimental, para ser estudado em laboratório, no qual será implementado um sistema de monitorização contínuo e automático. Sobre este demonstrador será feita uma análise de diferentes grandezas em medição, tais como: deslocamentos, extensões, temperatura, rotações e acelerações. Com carácter inovador, pretende-se ainda incluir neste modelo em sintonia de medição de coordenadas GNSS com o qual se torna possível medir deslocamentos absolutos. Os resultados experimentais alcançados serão analisados e comparados com modelos numéricos. Conferem-se os resultados experimentais de natureza estática e dinâmica, com os resultados numéricos de dois modelos de elementos finitos: um de barras e outro de casca. Realizaram-se diferentes abordagens tendo em conta as características identificadas por via experimental e calculadas nos modelos numéricos para melhor ajuste e calibração dos modelos numéricos Por fim, recorre-se a algoritmos de processamento e tratamento do respetivo sinal com aplicação de filtros, que revelam melhorar com rigor o sinal, de forma a potenciar as técnicas de fusão multisensor. Pretende-se integrar o sinal GNSS com os demais sensores presentes no sistema de monitorização. As técnicas de fusão multisensor visam melhor o desempenho deste potencial sistema de medição, demonstrando as suas valências no domínio da monitorização estrutural.