Simulation and life cycle assessment of process design alternatives for biodiesel production from waste vegetable oils

This study uses the process simulator ASPEN Plus and Life Cycle Assessment (LCA) to compare three process design alternatives for biodiesel production from waste vegetable oils that are: the conventional alkali-catalyzed process including a free fatty acids (FFAs) pre-treatment, the acid-catalyzed process, and the supercritical methanol process using propane as co-solvent. Results show that the supercritical methanol process using propane as co-solvent is the most environmentally favorable alternative. Its smaller steam consumption in comparison with the other process design alternatives leads to a lower contribution to the potential environmental impacts (PEI’s). The acid-catalyzed process generally shows the highest PEI’s, in particular due to the high energy requirements associated with methanol recovery operations.

Fractional order models of leaves

Leaves are mainly responsible for food production in vascular plants. Studying individual leaves can reveal important characteristics of the whole plant, namely its health condition, nutrient status, the presence of viruses and rooting ability. One technique that has been used for this purpose is Electrical Impedance Spectroscopy, which consists of determining the electrical impedance spectrum of the leaf. In this paper we use EIS and apply the tools of Fractional Calculus to model and characterize six species. Two modeling approaches are proposed: firstly, Resistance, Inductance, Capacitance electrical networks are used to approximate the leaves’ impedance spectra; afterwards, fractional-order transfer functions are considered. In both cases the model parameters can be correlated with physical characteristics of the leaves.

Structuring and moodleing a course: case studies at the polytechnic of Porto - School of engineering

This work presents a comparative study covering four different courses lectured at the Polytechnic of Porto - School of Engineering, in respect to the usage of a particular Learning Management System, i.e. Moodle, and its impact on students' results. Even though positive correlation factors exist, e.g. between the number of Moodle accesses versus the final exam grade obtained by each student, the explanation behind it may not be straightforward. Mapping this particular factor to course numbers reveals that the quality of the resources might be preponderant and not only their quantity. This paper also addresses teachers who used this platform as a complement to their courses (b-learning) and identifies some particular issues they should be aware in order to potentiate students' engagement and learning.

Engaging students by moodleing a course? Case studies at the Polytechnic of Porto–School of Engineering

This work presents a comparative study covering four different courses lectured at the Polytechnic of Porto - School of Engineering, regarding the usage of a particular Learning Management System, i.e. Moodle, and its impact on students' results. This study addresses teachers who used this platform as a complement to their courses (b-learning) and identifies some particular issues in order to potentiate students' engagement and learning. Even though positive correlation factors exist, e.g. between the number of Moodle accesses versus the final exam grade obtained by each student, the explanation behind it may not be straightforward. Mapping this particular factor to course numbers reveals that the quality of the resources might be preponderant and not only their quantity. These results point to the fact that some dynamic resources might enlarge students' engagement.

Virtual Communities of Practice: Design and Development of Support Platforms and Participation Fostering

Mestrado em Engenharia Informática - Área de Especialização em Sistemas Gráficos e Multimédia

The influence of task design on upper limb muscles fatigue during low-load repetitive work: A systematic review

Ergonomic interventions such as increased scheduled breaks or job rotation have been proposed to reduce upper limb muscle fatigue in repetitive low-load work. This review was performed to summarize and analyze the studies investigating the effect of job rotation and work-rest schemes, as well as, work pace, cycle time and duty cycle, on upper limb muscle fatigue. The effects of these work organization factors on subjective fatigue or discomfort were also analyzed. This review was based on relevant articles published in PubMed, Scopus and Web of Science. The studies included in this review were performed in humans and assessed muscle fatigue in upper limbs. 14 articles were included in the systematic review. Few studies were performed in a real work environment and the most common methods used to assess muscle fatigue were surface electromyography (EMG). No consistent results were found related to the effects of job rotation on muscle activity and subjective measurements of fatigue. Rest breaks had some positive effects, particularly in perceived discomfort. The increase in work pace reveals a higher muscular load in specific muscles. The duration of experiments and characteristics of participants appear to be the factors that most have influenced the results. Future research should be focused on the improvement of the experimental protocols and instrumentation, in order to the outcomes represent adequately the actual working conditions. Relevance to industry: Introducing more physical workload variation in low-load repetitive work is considered an effective ergonomic intervention against muscle fatigue and musculoskeletal disorders in industry. Results will be useful to identify the need of future research, which will eventually lead to the adoption of best industrial work practices according to the workers capabilities.