Otimização da extração sólido-líquido de antioxidantes de subprodutos florestais pelo método de superfície de resposta

Portugal continental apresenta uma vasta área florestal, que representa cerca de 35,4% da ocupação total do solo, com predominância de espécies como o eucalipto (Eucalyptus globulus) e o pinheiro-bravo (Pinus pinaster). Estas espécies apresentam uma elevada importância a nível económico, designadamente devido à sua ampla utilização, nomeadamente na indústria de celulose e papel, gerando elevadas quantidades de resíduos. Este resíduo de biomassa florestal é utilizado, na sua totalidade, para a geração de energia, na forma de eletricidade ou aquecimento. No entanto, existem outras opções viáveis, a nível económico, tais como a valorização destes subprodutos como fonte de compostos polifenólicos tornando-os, assim, um produto de valor acrescentado. A extração de compostos fenólicos de subprodutos florestais, como folhas de eucalipto e agulhas de pinheiros tem vindo a aumentar devido, principalmente, à substituição de antioxidantes sintéticos, contribuindo para a valorização de subprodutos florestais. Contudo, apesar de todas as potenciais aplicações e vantagens, apenas algumas centenas de espécies aromáticas identificadas são utilizadas à escala comercial. Neste trabalho foi avaliada a capacidade antioxidante de subprodutos da floresta, otimizando as condições de extração através do estudo dos fatores: tempo de extração, temperatura e composição de solvente através do método de superfície de resposta. O planeamento experimental utilizado teve como base um planeamento de compósito central e a avaliação do perfil de antioxidantes das matrizes analisadas foi realizada através de métodos de quantificação total, como o teor fenólico total, a atividade anti-radicalar – método do DPPH (radical 2,2-difenil-1-picrilhidrazilo) e o método de FRAP. Estes métodos analíticos convencionais foram modificados e, devidamente validados, para a análise em leitor de microplacas. Verificou-se que os extratos de pinheiro e de eucalipto, tanto as amostras verdes com as amostras, apresentam uma promissora capacidade antioxidante. O planeamento fatorial aplicado permitiu otimizar as condições de extração em relação às matrizes verdes. Contudo, o mesmo não se verificou em relação às matrizes secas. A composição (% de água) é sem dúvida o fator com mais efeito em todas as amostras (coeficientes de primeira e segunda ordem no modelo). Também a temperatura foi identificada como um fator com efeito significativo sobre os sistemas em análise.

Early physiological and biochemical responses of rice seedlings to low concentration of microcystin-LR

Microcystin-leucine and arginine (microcystin- LR) is a cyanotoxin produced by cyanobacteria like Microcystis aeruginosa, and it’s considered a threat to water quality, agriculture, and human health. Rice (Oryzasativa) is a plant of great importance in human food consumption and economy, with extensive use around the world. It is therefore important to assess the possible effects of using water contaminated with microcystin-LR to irrigate rice crops, in order to ensure a safe, high quality product to consumers. In this study, 12 and 20-day-old plants were exposed during 2 or 7 days to a M. aeruginosa extract containing environmentally relevant microcystin-LR concentrations, 0.26–78 lg/L. Fresh and dry weight of roots and leaves, chlorophyll fluorescence, glutathione S-transferase and glutathione peroxidase activities, and protein identification by mass spectrometry through two-dimensional gel electrophoresis from root and leaf tissues, were evaluated in order to gauge the plant’s physiological condition and biochemical response after toxin exposure. Results obtained from plant biomass, chlorophyll fluorescence, and enzyme activity assays showed no significant differences between control and treatment groups. How- ever, proteomics data indicates that plants respond to M. aeruginosa extract containing environmentally relevant microcystin-LR concentrations by changing their metabolism, responding differently to different toxin concentrations. Biological processes most affected were related to protein folding and stress response, protein biosynthesis, cell signalling and gene expression regulation, and energy and carbohydrate metabolism which may denote a toxic effect induced by M. aeruginosa extract and microcystin- LR. Theimplications of the metabolic alterations in plant physiology and growth require further elucidation.

Association between dairy product intake and abdominal obesity in Azorean adolescents

BACKGROUND: Some studies have reported an inverse association between dairy product (DP) consumption and weight or fat mass loss. OBJECTIVES: The objective of our study was to assess the association between DP intake and abdominal obesity (AO) among Azorean adolescents. SUBJECTS/METHODS: This study was a cross-sectional analysis. A total of 903 adolescents (370 boys) aged 15--16 years was evaluated. Anthropometric measurements were collected (weight, height and waist circumference (WC)) and McCarthy’s cut-points were used to categorize WC. AO was defined when WC was X90th percentile. Adolescent food intake was assessed using a self-administered semiquantitative food frequency questionnaire and DP intake was categorized in o2 and X2 servings/day. Data were analyzed separately for girls and boys, and logistical regression was used to estimate the association between DPs and AO adjusting for potential confounders. RESULTS: The prevalence of AO was 54.9% (boys: 32.1% and girls: 70.7%, Po0.001). For boys and girls, DP consumption was 2.3±1.9 and 2.1±1.6 servings/day (P¼0.185), respectively. In both genders, the proportion of adolescents with WC o90th percentile was higher among individuals who reported a dairy intake of X2 servings/day compared with those with an intake o2 servings/day (boys: 71% vs 65% and girls: 36% vs 24%, Po0.05). After adjustments for confounders, two or more DP servings per day were a negative predictor of AO (odds ratio, 0.217; 95% confidence interval, 0.075 -- 0.633) only in boys. CONCLUSION: We found a protective association between DP intake and AO only in boys.

Implementação de um processo industrial de coloração de granito

O presente estágio foi desenvolvido na Britafiel. Um dos projectos em que a Empresa se encontra envolvida é o STOCO, pretendendo implementar à escala industrial um processo de coloração de pedra granítica natural para fins decorativos. Foi neste projecto que se enquadrou o estágio. O tema do estágio centra-se no processo de coloração de granito tendo como principal foco a implementação de um processo industrial de produção de granito colorido. O projecto STOCO nasce da necessidade de complementar a actividade da empresa com produtos de maior valor acrescentado para valorização da matéria-prima de base, o granito. STOCO, resultante de Stone Color, é o nome dado ao projecto e ao novo produto que é granito colorido, sob a forma de brita. Pretende-se obter um produto amigo do ambiente e com boas características: manter a textura natural da pedra granítica e assegurar uma boa resistência a factores agressivos. Estudos prévios de qualidade e de toxicidade mostraram que o produto STOCO desenvolvido até então apresenta um bom comportamento face a agressões climatéricas e que não compromete a vida das espécies usadas nos testes (peixes). Em relação aos lixiviados e resíduos da pedra colorida STOCO, estes não apresentaram qualquer problema ambiental, sendo considerado um produto amigo do ambiente. À data de início do presente trabalho estava em funcionamento um equipamento protótipo de produção de granito colorido (100 kg/partida), sendo a instalação e o arranque da unidade industrial (3 ton/h) concretizados no início de 2014, já no decorrer deste trabalho. Os objectivos cumpridos no âmbito deste trabalho foram então a implementação de uma linha industrial de produção de brita colorida, avaliação técnica do processo e do custo industrial de produção associado às matérias-primas. Neste relatório é descrito o processo inicial adoptado e apresentam-se as alterações efectuadas para melhoria do processo produtivo. Resolveram-se problemas como: definição e instalação de equipamentos complementares para a entrada e a saída da brita no equipamento industrial; pó excessivo na brita; cheiro intenso a gás e elevado ruído; adequação do sistema de pintura; e secagem incompleta da brita. Alguns destes problemas não foram totalmente resolvidos, mas sim minimizados. O equipamento industrial necessita ainda de alterações em diversas áreas, que foram identificadas e para as quais são feitas sugestões de melhoria. Conseguiu-se ainda fazer alguns testes para uma possível substituição de alguns constituintes da tinta. Os componentes que entram na composição base da tinta aquosa, são de modo simplificado: ligante, pigmento, solvente e aditivos. Os constituintes que mais encarecem a tinta, e consequentemente o processo em causa, são o ligante e o pigmento. Os estudos efectuados precisam de ser aprofundados, na tentativa de melhorar o processo minimizando os custos de produção. Formalizaram-se os procedimentos escritos de produção STOCO tanto para o protótipo como para o processo industrial e elaborou-se uma ficha técnica de produto para a brita colorida STOCO.

Synthesis of an antibody-like material for the detection of Albumin

6th Graduate Student Symposium on Molecular Imprinting

A novel antibody-like material for breast cancer antigen CA15-3, used to track breast cancer by potentiometric transduction

This work presents the development of a low cost sensor device for the diagnosis of breast cancer in point-of-care, made with new synthetic biomimetic materials inside plasticized poly(vinyl chloride), PVC, membranes, for subsequent potentiometric detection. This concept was applied to target a conventional biomarker in breast cancer: Breast Cancer Antigen (CA15-3). The new biomimetic material was obtained by molecularly-imprinted technology. In this, a plastic antibody was obtained by polymerizing around the biomarker that acted as an obstacle to the growth of the polymeric matrix. The imprinted polymer was specifically synthetized by electropolymerization on an FTO conductive glass, by using cyclic voltammetry, including 40 cycles within -0.2 and 1.0 V. The reaction used for the polymerization included monomer (pyrrol, 5.0×10-3 mol/L) and protein (CA15-3, 100U/mL), all prepared in phosphate buffer saline (PBS), with a pH of 7.2 and 1% of ethylene glycol. The biomarker was removed from the imprinted sites by proteolytic action of proteinase K. The biomimetic material was employed in the construction of potentiometric sensors and tested with regard to its affinity and selectivity for binding CA15-3, by checking the analytical performance of the obtained electrodes. For this purpose, the biomimetic material was dispersed in plasticized PVC membranes, including or not a lipophilic ionic additive, and applied on a solid conductive support of graphite. The analytical behaviour was evaluated in buffer and in synthetic serum, with regard to linear range, limit of detection, repeatability, and reproducibility. This antibody-like material was tested in synthetic serum, and good results were obtained. The best devices were able to detect 5 times less CA15-3 than that required in clinical use. Selectivity assays were also performed, showing that the various serum components did not interfere with this biomarker. Overall, the potentiometric-based methods showed several advantages compared to other methods reported in the literature. The analytical process was simple, providing fast responses for a reduced amount of analyte, with low cost and feasible miniaturization. It also allowed the detection of a wide range of concentrations, diminishing the required efforts in previous sample pre-treating stages.

Modeling and Control of a Dragonfly-Like Robot

Dragonflies demonstrate unique and superior flight performances than most of the other insect species and birds. They are equipped with two pairs of independently controlled wings granting an unmatchable flying performance and robustness. In this paper it is studied the dynamics of a dragonfly-inspired robot. The system performance is analyzed in terms of time response and robustness. The development of computational simulation based on the dynamics of the robotic dragonfly allows the test of different control algorithms. We study different movement, the dynamics and the level of dexterity in wing motion of the dragonfly. The results are positive for the construction of flying platforms that effectively mimic the kinematics and dynamics of dragonflies and potentially exhibit superior flight performance than existing flying platforms.

Ball Sensing in a Leg Like Robotic Kicker

The trend to have more cooperative play and the increase of game dynamics in Robocup MSL League motivates the improvement of skills for ball passing and reception. Currently the majority of the MSL teams uses ball handling devices with rollers to have more precise kicks but limiting the capability to kick a moving ball without stopping it and grabbing it. This paper addresses the problem to receive and kick a fast moving ball without having to grab it with a roller based ball handling device. Here, the main difficulty is the high latency and low rate of the measurements of the ball sensing systems, based in vision or laser scanner sensors.Our robots use a geared leg coupled to a motor that acts simultaneously as the kicking device and low level ball sensor. This paper proposes a new method to improve the capability for ball sensing in the kicker, by combining high rate measurements from the torque and energy in the motor and angular position of the kicker leg. The developed method endows the kicker device with an effective ball detection ability, validated in several game situations like in an interception to a fast pass or when chasing the ball where the relative speed from robot to ball is low. This can be used to optimize the kick instant or by the embedded kicker control system to absorb the ball energy.

Projecto de Instalação de Processamento de Material Feldspático. Caso de Estudo:Argemela

Feldspato é o nome dado a uma importante família de minerais, do grupo dos tectossilicatos, que compõem o material rochoso de mais de 60% da crusta terrestre. Estes minerais são constituintes essenciais da maior parte das rochas cristalinas e a sua importância é tal que o seu estudo constitui um capítulo fundamental da petrografia. Dada a sua grande incidência na crusta terrestre, os feldspatos ocorrem em diversos cenários geológicos, desde os depósitos pegmatitos, aos aplitos, granitos, sienitos nefelínicos e ainda areias feldspáticas. As suas características químicas, físicas e mineralógicas fazem com que este grupo de minerais esteja presente nas mais diversificadas indústrias, tais como a vidreira, cerâmica, tintas, borrachas, plásticos, abrasivos ligeiros, elétrodos de soldadura, entre outros. Em Portugal, as principais unidades produtoras de feldspatos encontram‐se distribuídas pelo Norte e Centro do país, mais concretamente pelos distritos de Viana do Castelo, Braga, Vila Real, Porto, Viseu e Guarda. Novos estudos geológicos acompanhados de prospeções, nomeadamente na região do maciço central, têm sido efetuados com vista à descoberta de novos depósitos com potencial para exploração deste importante mineral. O depósito aplítico da Argemela, no concelho do Fundão apresenta‐se como um depósito cujas dimensões e qualidade apresentadas indicam a possibilidade de exploração. Nesse sentido, o presente trabalho consiste em analisar e caracterizar os materiais presentes na quele depósito mineral, tendo em vista a respectiva aplicação industrial, e posteriormente propor uma instalação de processamento do material para que o mesmo seja comercializado. Também será objeto deste trabalho a análise da viabilidade económica do projeto, mais concretamente fazendo a previsão do investimento inicial de modo a somar os custos de produção correntes e avaliar o retorno com base na comercialização do material no modo “Ex Works”.

Voltammetric analysis of mancozeb and its degradation product ethylenethiourea

The purpose of this work was to develop a reliable alternative method for the determination of the dithiocarbamate pesticide mancozeb (MCZ) in formulations. Furthermore, a method for the analysis of MCZ's major degradation product, ethylenethiourea (ETU), was also proposed. Cyclic voltammetry was used to characterize the electrochemical behavior of MCZ and ETU, and square-wave adsorptive stripping voltammetry (SWAdSV) was employed for MCZ quantification in commercial formulations. It was found that both MCZ and ETU are irreversibly reduced (− 0.6 V and − 0.5 V vs Ag/AgCl, respectively) at the surface of a glassy carbon electrode in a mainly diffusion-controlled process, presenting maximum peak current intensities at pH 7.0 (in phosphate buffered saline electrolyte). Several parameters of the SWAdSV technique were optimized and linear relationships between concentration and peak current intensity were established between 10–90 μmol L− 1 and 10–110 μmol L− 1 for MCZ and ETU, respectively. The limits of detection were 7.0 μmol L− 1 for MCZ and 7.8 μmol L− 1 for ETU. The optimized method for MCZ was successfully applied to the quantification of this pesticide in two commercial formulations. The developed procedures provided accurate and precise results and could be interesting alternatives to the established methods for quality control of the studied products, as well as for analysis of MCZ and ETU in environmental samples.

The logo is not flat: evolving picture marks

From the boom of corporate identity in the 50s, 60 years have passed, and we now see picture marks become more complex and question axioms of identity design, like simplicity or bidimensionality. In these changing times, where access to technology and to information makes it possible for one to see the world as a ‘flat’ place [1], where virtually anyone with a computer can create, it is worth considering how much has changed and how much remains the same in picture marks design. Are the silent designers [2] — the technology and software — growing louder? Are picture marks mimicking each other? Are graphic marks following trendy solutions? It is clear the change of paradigms the new technologies have over the graphic zeitgeist. However, what are the consequences of the transformation in the modus operandi and its result in picture marks evolving solutions? And what does this evolution say about us? Being both a condensation of meaning about a corporation or institution and a rhetorical instrument by which to persuade an audience that a product or entity has distinctive and desirable qualities, picture marks are, therefore, a condensed representation of social identity. They are signs full of signification beyond themselves, representing ourselves and our world and by means of its analysis we can learn a bit more about our role as designers, our relation towards new technologies and foresee our role as designers in the future.

Towards Human-like Bimanual Movements in Anthropomorphic Robots: A Nonlinear Optimization Approach

Previously we have presented a model for generating human-like arm and hand movements on an unimanual anthropomorphic robot involved in human-robot collaboration tasks. The present paper aims to extend our model in order to address the generation of human-like bimanual movement sequences which are challenged by scenarios cluttered with obstacles. Movement planning involves large scale nonlinear constrained optimization problems which are solved using the IPOPT solver. Simulation studies show that the model generates feasible and realistic hand trajectories for action sequences involving the two hands. The computational costs involved in the planning allow for real-time human robot-interaction. A qualitative analysis reveals that the movements of the robot exhibit basic characteristics of human movements.

Crowdsourcing innovation intermediaries functions

Open innovation is a hot topic in innovation management. Its basic premise is open up the innovation process. The innovation process, in general sense, may be seen as the process of designing, developing and commercializing a novel product or service to improve the value added of a company. The development of Web 2.0 tools facilitates this kind of contributions, opening space to the emergence of crowdsourcing innovation initiatives. Crowdsourcing is a form of outsourcing not directed to other companies but to the crowd by means of an open call mostly through an Internet platform. Innovation intermediaries, in general sense, are organizations that work to enable innovation, that just act as brokers or agents between two or more parties. Usually, they are also engaged in other activities like inter-organizational networking and technology development and related activities. A crowdsourcing innovation intermediary is an organization that mediates the communication and relationship between the seekers – companies that aspire to solve some problem or to take advantage of any business opportunity – with a crowd that is prone to give ideas based on their knowledge, experience and wisdom. This paper identifies and analyses the functions to be performed by an intermediary of crowdsourcing innovation through grounded theory analyses from literature. The resulting model is presented and explained. The resulting model summarizes eight main functions that can be performed by a crowdsourcing process, namely, diagnoses, mediation, linking knowledge, community, evaluation, project management, intellectual property governance and marketing and support. These functions are associated with a learning cycle process which covers all the crowdsourcing activities that can be realized by the broker.