Classificação e previsão de cardiotocogramas usando algoritmos baseados em redes neuronais

Mestrado em Computação e Instrumentação Médica

Study on the changes of soil chemical characteristics as result of prescribed fire

Every year, particularly during the summer period, the Portuguese forests are devastated by forest fire that destroys their ecosystems. So in order to prevent these forest fires, public and private authorities frequently use methods for the reduction of combustible mass as the prescribed fire and the mechanical vegetation pruning. All of these methods of prevention of forest fires alter the vegetation layer and/or soil [1-2]. This work aimed the study of the variation of some chemical characteristics of soil that suffered prescribed fire. The studied an area was located in the Serra of Cabreira (Figure 1) with 54.6 ha. Twenty sampling points were randomly selected and samples were collected with a shovel before, just after the prescribed fire, and 125 and 196 days after that event. The parameters that were studied were: pH, soil moisture, organic matter and iron, magnesium and potassium total concentration. All the analysis followed International Standard Methodologies. This work allowed to conclude that: a) after the prescribed fire; i) the pH remained practically equal to the the initial value; ii) occurred a slight increase of the average of the organic matter contents and iron total contents; b) at the end of the sampling period compared to the initial values; i) the pH didn´t change significantly; ii) the average of the contents of organic matter decreased; and iii) the average of the total contents of Fe, Mg and K increased.

Multiple Linear Regression and Artificial Neural Networks to Predict Time and Efficiency of Soil Vapor Extraction

The prediction of the time and the efficiency of the remediation of contaminated soils using soil vapor extraction remain a difficult challenge to the scientific community and consultants. This work reports the development of multiple linear regression and artificial neural network models to predict the remediation time and efficiency of soil vapor extractions performed in soils contaminated separately with benzene, toluene, ethylbenzene, xylene, trichloroethylene, and perchloroethylene. The results demonstrated that the artificial neural network approach presents better performances when compared with multiple linear regression models. The artificial neural network model allowed an accurate prediction of remediation time and efficiency based on only soil and pollutants characteristics, and consequently allowing a simple and quick previous evaluation of the process viability.

Performance evaluation of a cooperative reputation system for vehicular delay-tolerant networks

In the last decade, both scientific community and automotive industry enabled communications among vehicles in different kinds of scenarios proposing different vehicular architectures. Vehicular delay-tolerant networks (VDTNs) were proposed as a solution to overcome some of the issues found in other vehicular architectures, namely, in dispersed regions and emergency scenarios. Most of these issues arise from the unique characteristics of vehicular networks. Contrary to delay-tolerant networks (DTNs), VDTNs place the bundle layer under the network layer in order to simplify the layered architecture and enable communications in sparse regions characterized by long propagation delays, high error rates, and short contact durations. However, such characteristics turn contacts very important in order to exchange as much information as possible between nodes at every contact opportunity. One way to accomplish this goal is to enforce cooperation between network nodes. To promote cooperation among nodes, it is important that nodes share their own resources to deliver messages from others. This can be a very difficult task, if selfish nodes affect the performance of cooperative nodes. This paper studies the performance of a cooperative reputation system that detects, identify, and avoid communications with selfish nodes. Two scenarios were considered across all the experiments enforcing three different routing protocols (First Contact, Spray and Wait, and GeoSpray). For both scenarios, it was shown that reputation mechanisms that punish aggressively selfish nodes contribute to increase the overall network performance.

Effects of hotel characteristics on room rates in Porto: a hedonic price approach

According to the hedonic price method, a price of a good is related with the characteristics or the services it provides. Within this framework, the aim of this study it is to examine the effect on room rates of different characteristics of hotels in and around the city of Porto, such as star category, size, room and service quality, hotel facilities and location. It was estimated a hedonic price function, using data for 51 hotels. The results enable to identify the attributes that are important to consumers and hoteliers and to which extent. This information can be used by hotel managers to define a price strategy and helpful in new investment decisions.

Multidimensional Frailty and Pain in Community Dwelling Elderly

Artigo científico disponível actualmente em Early View (Online Version of Record published before inclusion in an issue)

Indizar, clasificar y organizar las colecciones de las bibliotecas escolares: herramientas en lengua española y portuguesa

La biblioteca escolar es un servicio de información básico para todos los miembros de una comunidad educativa, que forma parte de los espacios docentes de los centros y de los procesos pedagógicos que tienen lugar en ellos. Las bibliotecas escolares funcionan como centros de recursos para las actividades de enseñanza-aprendizaje, están constituidas por un conjunto sistematizado y dinámico de servicios y fondos documentales que permiten a los usuarios desarrollar hábitos lectores y buscar y valorar las fuentes de información, entre otras relevantes funciones. Los recursos de información que albergan son uno de sus principales activos, pero si colección documental no está organizada, las tareas de búsqueda y localización de la información resultarán complicadas y la calidad de los recursos obtenidos, cuestionable. Los bibliotecarios deben conocer en profundidad las características específicas del fondo documental y las fuentes disponibles; las técnicas y herramientas adecuadas para procesar y tratar el fondo bibliográfico, así como los métodos de recuperación de la información más convenientes. En este contexto, el objetivo de este trabajo es analizar de forma pormenorizada los procesos de indización y clasificación que se realizan en las bibliotecas escolares para procesar y recuperar la información que albergan su colecciones, así como describir las características más relevantes de las herramientas específicas que se usan en las bibliotecas escolares españolas, brasileñas y portuguesas, adaptadas a las características de los usuarios que utilizan sus servicios y acuden a ellas para resolver necesidades de información. Para lograr este propósito, se analiza el concepto de biblioteca escolar de forma crítica, se estudian sus funciones y se examinan las técnicas y los instrumentos que permiten organizar la información. Entre otras herramientas, se estudian listas de encabezamientos de materia como los Encabezamientos de materia para libros infantiles y juveniles y la Lista de Encabezamientos de materia para las bibliotecas públicas; sistemas de clasificación, como la Clasificación Decimal Universal (edición de bolsillo) o la clasificación por centros de interés y tesauros especializados como el Tesauro de la Educación UNESCO-OIE y el Tesauro Europeo de la Educación, entre otros.

Electrospun Polyaniline-Reduced Graphene Oxide Composite Nanofibers Based High Sensitive Ammonia Gas Sensor

Ammonia is an important gas in many power plants and industrial processes so its detection is of extreme importance in environmental monitoring and process control due to its high toxicity. Ammonia’s threshold limit is 25 ppm and the exposure time limit is 8 h, however exposure to 35 ppm is only secure for 10 min. In this work a brief introduction to ammonia aspects are presented, like its physical and chemical properties, the dangers in its manipulation, its ways of production and its sources. The application areas in which ammonia gas detection is important and needed are also referred: environmental gas analysis (e.g. intense farming), automotive-, chemical- and medical industries. In order to monitor ammonia gas in these different areas there are some requirements that must be attended. These requirements determine the choice of sensor and, therefore, several types of sensors with different characteristics were developed, like metal oxides, surface acoustic wave-, catalytic-, and optical sensors, indirect gas analyzers, and conducting polymers. All the sensors types are described, but more attention will be given to polyaniline (PANI), particularly to its characteristics, syntheses, chemical doping processes, deposition methods, transduction modes, and its adhesion to inorganic materials. Besides this, short descriptions of PANI nanostructures, the use of electrospinning in the formation of nanofibers/microfibers, and graphene and its characteristics are included. The created sensor is an instrument that tries to achieve a goal of the medical community in the control of the breath’s ammonia levels being an easy and non-invasive method for diagnostic of kidney malfunction and/or gastric ulcers. For that the device should be capable to detect different levels of ammonia gas concentrations. So, in the present work an ammonia gas sensor was developed using a conductive polymer composite which was immobilized on a carbon transducer surface. The experiments were targeted to ammonia measurements at ppb level. Ammonia gas measurements were carried out in the concentration range from 1 ppb to 500 ppb. A commercial substrate was used; screen-printed carbon electrodes. After adequate surface pre-treatment of the substrate, its electrodes were covered by a nanofibrous polymeric composite. The conducting polyaniline doped with sulfuric acid (H2SO4) was blended with reduced graphene oxide (RGO) obtained by wet chemical synthesis. This composite formed the basis for the formation of nanofibers by electrospinning. Nanofibers will increase the sensitivity of the sensing material. The electrospun PANI-RGO fibers were placed on the substrate and then dried at ambient temperature. Amperometric measurements were performed at different ammonia gas concentrations (1 to 500 ppb). The I-V characteristics were registered and some interfering gases were studied (NO2, ethanol, and acetone). The gas samples were prepared in a custom setup and were diluted with dry nitrogen gas. Electrospun nanofibers of PANI-RGO composite demonstrated an enhancement in NH3 gas detection when comparing with only electrospun PANI nanofibers. Was visible higher range of resistance at concentrations from 1 to 500 ppb. It was also observed that the sensor had stable, reproducible and recoverable properties. Moreover, it had better response and recovery times. The new sensing material of the developed sensor demonstrated to be a good candidate for ammonia gas determination.

Characterization of green zero-valent iron nanoparticles produced with tree leaf extracts

In the last decades nanotechnology has become increasingly important because it offers indisputable advantages to almost every area of expertise, including environmental remediation. In this area the synthesis of highly reactive nanomaterials (e.g. zero-valent iron nanoparticles, nZVI) is gaining the attention of the scientific community, service providers and other stakeholders. The synthesis of nZVI by the recently developed green bottom-up method is extremely promising. However, the lack of information about the characteristics of the synthetized particles hinders a wider and more extensive application. This work aims to evaluate the characteristics of nZVI synthesized through the green method using leaves from different trees. Considering the requirements of a product for environmental remediation the following characteristics were studied: size, shape, reactivity and agglomeration tendency. The mulberry and pomegranate leaf extracts produced the smallest nZVIs (5–10 nm), the peach, pear and vine leaf extracts produced the most reactive nZVIs while the ones produced with passion fruit, medlar and cherry extracts did not settle at high nZVI concentrations (931 and 266 ppm). Considering all tests, the nZVIs obtained from medlar and vine leaf extracts are the ones that could present better performances in the environmental remediation. The information gathered in this paper will be useful to choose the most appropriate leaf extracts and operational conditions for the application of the green nZVIs in environmental remediation.

Influence of Firms’ Environmental Management and Community Involvement Programs in their Employees and in the Community

To assure enduring success, firms need to generate economic value with respect for the environment and social value. They also need to be aware of the needs and expectations of relevant stakeholders and incorporate them in their business strategies and programs. These challenges imply that engineers should take into consideration societal, health and safety,environmental and commercial issues in their professional activity. This investigation accesses the influence of firms’ environmental management programs and community involvement programs on their own employees and in the community, with a focus on small and medium companies. Based on a quantitative research, the findings suggest that firms that invest both in environmental management programs and in community involvement programs have a higher involvement of their own employees with the community, while at the same time receiving more feedback (positive, but also negative) from the community, stressing the need to pay special attention to their communication policies.

A Study on Microstructure Characteristics of TEPs-modified Adhesives

Thermally expandable particles (TEPs) were developed by Dow Chemical Co in the early 1970´s [1] and were further developed by others [2, 3]. They are particles made up of a thermoplastic shell filled with liquid hydrocarbon. On heating them, two transformations will occur. One is the softening of shell material and the other is the gasification of the hydrocarbon liquid inside it. As a consequence, the shell will expand as the gas inside it will push the softened shell from inside out causing it to grow in size [4]. When fully expanded, the growth in volume of the particle can be from 50 to 100 times [3]. Owing to this unique behaviour, TEPs are used by the industry in a wide variety of applications mainly for weight reduction and appearance improvement for thermoplastics, inks, and coatings. In adhesive bonding, TEPs have been used for recycling purposes. Moreover, TEPs might be used to modify structural adhesives for other new purposes, such as: to increase the joint strength by creating an adhesive functionally modified along the overlap of the joint by gradual heating and/or to heal the adhesive in case of damage.

Diffusion characteristics of ethylene glycol in skeletal muscle

Part of the optical clearing study in biological tissues concerns the determination of the diffusion characteristics of water and optical clearing agents in the subject tissue. Such information is sufficient to characterize the time dependence of the optical clearing mechanisms—tissue dehydration and refractive index (RI) matching. We have used a simple method based on collimated optical transmittance measurements made from muscle samples under treatment with aqueous solutions containing different concentrations of ethylene glycol (EG), to determine the diffusion time values of water and EG in skeletal muscle. By representing the estimated mean diffusion time values from each treatment as a function of agent concentration in solution, we could identify the real diffusion times for water and agent. These values allowed for the calculation of the correspondent diffusion coefficients for those fluids. With these results, we have demonstrated that the dehydration mechanism is the one that dominates optical clearing in the first minute of treatment, while the RI matching takes over the optical clearing operations after that and remains for a longer time of treatment up to about 10 min, as we could see for EG and thin tissue samples of 0.5 mm.

Significance of Biogenic Amines in Cold-Smoked Fish and Their Relation to Microbiological Characteristics of Products Available in Portuguese Retail Markets

Studies on microbial characterization of cold-smoked salmon and salmon trout during cold storage were performed on samples available in the Portuguese market. Samples were also classified microbiologically according to guidelines for ready-to-eat (RTE) products. Further investigations on sample variability and microbial abilities to produce tyramine and histamine were also performed. The coefficient of variation for viable counts of different groups of microorganisms of samples collected at retail market point was high in the first 2 wk of storage, mainly in the Enterobacteriaceae group and aerobic plate count (APC), suggesting that microbiological characteristics of samples were different in numbers, even within the same batch from the same producer. This variation seemed to be decreased when storage and temperature were controlled under lab conditions. The numbers of Enterobacteriaceae were influenced by storage temperature, as indicated by low microbial numbers in samples from controlled refrigeration. Lactic acid bacteria (LAB) and Enterobacteriaceae were predominant in commercial products, a significant percentage of which were tyramine and less histamine producers. These results might be influenced by (1) the technological processes in the early stages of production, (2) contamination during the smoking process, and (3) conditions and temperature fluctuations during cold storage at retail market point of sale.

As atividades de enriquecimento curricular e a pedagogia do lazer

Nas últimas décadas a sociedade tem sido palco de várias mudanças, reflexo do desenvolvimento de uma sociedade cada vez mais globalizada. Este desenvolvimento emergente da sociedade, gerou novas necessidades e impôs também novos desafios à instituição escolar. Uma das novas necessidades, à qual a escola precisou responder, foi a de ocupar por mais tempo as crianças na escola e alargar a sua oferta pedagógica, uma vez que, atualmente, a maioria dos pais trabalha. Surge assim, o conceito de escola a tempo inteiro e a implementação das atividades de enriquecimento curricular (AEC). As AEC vieram substituir as atividades de tempos livres, que se destinavam a proporcionar atividades de lazer e que possibilitavam que a criança escolhesse sobre o que fazer e como. A significativa alteração na organização e funcionamento das escolas, decorrente da implementação das AEC, veio suscitar dúvidas nos professores e comunidade educativa, que se viram confrontados com a longa permanência dos alunos na escola, a pouca disponibilidade das crianças para brincadeiras, em resultado de um horário escolar preenchido em atividades, desvalorizando-se o brincar espontâneo das crianças como forma de interação e construção de conhecimento. Reconhecendo a importância das atividades lúdicas no desenvolvimento global da criança, este estudo pretende contribuir para o desenvolvimento das AEC, num contexto lúdico, suportado pelas caraterísticas do lazer.