SiC Multilayer Structures as Light Controlled Photonic Active Filters

Tunable wavelength division multiplexing converters based on amorphous SiC multilayer photonic active filters are analyzed. The configuration includes two stacked p-i-n structures (p(a-SiC:H)-i'(a-SiC:H)-n(a-SiC:H)-p(a-SiC:H)-i(a-Si:H)-n(a-Si:H)) sandwiched between two transparent contacts. The manipulation of the magnitude is achieved through appropriated front and back backgrounds. Transfer function characteristics are studied both theoretically and experimentally. An algorithm to decode the multiplex signal is established. An optoelectronic model supports the optoelectronic logic architecture. Results show that the light-activated device combines the demultiplexing operation with the simultaneous photodetection and self-amplification of an optical signal. The output waveform presents a nonlinear amplitude-dependent response to the wavelengths of the input channels. Depending on the wavelength of the external background and irradiation side, it acts either as a short- or a long-pass band filter or as a band-stop filter. A two-stage active circuit is presented and gives insight into the physics of the device.

Light memory operation based on a double pin SiC device

Experimental optoelectronic characterization of a p-i'(a-SiC:H)-n/pi(a-Si:H)-n heterostructure with low conductivity doped layers shows the feasibility of tailoring channel bandwidth and wavelength by optical bias through back and front side illumination. Front background enhances light-to-dark sensitivity of the long and medium wavelength range, and strongly quenches the others. Back violet background enhances the magnitude in short wavelength range and reduces the others. Experiments have three distinct programmed time slots: control, hibernation and data. Throughout the control time slot steady light wavelengths illuminate either or both sides of the device, followed by the hibernation without any background illumination. The third time slot allows a programmable sequence of different wavelengths with an impulse frequency of 6000Hz to shine upon the sensor. Results show that the control time slot illumination has an influence on the data time slot which is used as a volatile memory with the set, reset logical functions. © IFIP International Federation for Information Processing 2015.

Field effect and light-assisted a-Si:H sensors for detection of ions in solution

In this paper we present an amorphous silicon device that can be used in two operation modes to measure the concentration of ions in solution. While crystalline devices present a higher sensitivity, their amorphous counterpart present a much lower fabrication cost, thus enabling the production of cheap disposable sensors for use, for example, in the food industry. The devices were fabricated on glass substrates by the PECVD technique in the top gate configuration, where the metallic gate is replaced by an electrolytic solution with an immersed Ag/AgCl reference electrode. Silicon nitride is used as gate dielectric enhancing the sensitivity and passivation layer used to avoid leakage and electrochemical reactions. In this article we report on the semiconductor unit, showing that the device can be operated in a light-assisted mode, where changes in the pH produce changes on the measured ac photocurrent. In alternative the device can be operated as a conventional ion selective field effect device where changes in the pH induce changes in the transistor's threshold voltage.

Fluorescence Microscopy Imaging Denoising with Log-Euclidean Priors and Photobleaching Compensation

Fluorescent protein microscopy imaging is nowadays one of the most important tools in biomedical research. However, the resulting images present a low signal to noise ratio and a time intensity decay due to the photobleaching effect. This phenomenon is a consequence of the decreasing on the radiation emission efficiency of the tagging protein. This occurs because the fluorophore permanently loses its ability to fluoresce, due to photochemical reactions induced by the incident light. The Poisson multiplicative noise that corrupts these images, in addition with its quality degradation due to photobleaching, make long time biological observation processes very difficult. In this paper a denoising algorithm for Poisson data, where the photobleaching effect is explicitly taken into account, is described. The algorithm is designed in a Bayesian framework where the data fidelity term models the Poisson noise generation process as well as the exponential intensity decay caused by the photobleaching. The prior term is conceived with Gibbs priors and log-Euclidean potential functions, suitable to cope with the positivity constrained nature of the parameters to be estimated. Monte Carlo tests with synthetic data are presented to characterize the performance of the algorithm. One example with real data is included to illustrate its application.

Análise dos métodos de medição dos parâmetros geométricos de via e correlação entre os dados obtidos

A razão atribuída à escolha do tema do T.F.M. em Caminhos-de-ferro, tem a ver com o facto de ser uma via de comunicação específica. Contrariamente ao que acontece na execução de auto-estradas, no caminho-de-ferro, a gestora da infra-estrutura responsabiliza-se pela execução, exploração (sinalização e controlo de circulação), abastecimento de energia fornecida às vias que dispõem de catenária (tracção eléctrica), manutenção e conservação da via. O processo de análise e inspecção de geometria de via, é usado quando e necessário preservar a infra-estrutura. Este processo iniciou-se nos caminhos-de-ferro portugueses, há muitos anos, depois da inauguração do primeiro troco de linha férrea. A primeira viagem ocorre em Outubro de 1856, sendo o início do processo em 1968, com a dresina “Matisa PV-6”. Em 1991 a C.P. adquiriu outro veículo de inspecção de via, tendo sido escolhido o VIV02 EM 120 da marca Plasser & Theurer, para substituir “Matisa PV-6”. O tema Análise dos Métodos de Medição dos Parâmetros Geométricos de Via e Correlação entre os Dados Obtidos está directamente relacionado com a manutenção e conservação de via. Na Unidade Operacional Sul (hoje ROS – Região Operacional Sul), local onde desenvolvi o T.F.M., não existem obras de construção de caminhos-de-ferro que pudesse acompanhar e constituir tema para o meu trabalho. Na realidade, com a falta de investimento que se perspectiva no futuro próximo, a manutenção da infra-estrutura passa a ser a actividade principal desenvolvida pela REFER, de modo a assegurar a comodidade, segurança e rapidez na deslocação de cargas e pessoas. A Analise Geométrica de Via e actualmente uma das principais actividades no âmbito da manutenção, que é feita por diagnóstico, contrariamente ao que acontecia no passado em que a conservação metódica era realizada num determinado ano num troço seleccionado independentemente da necessidade ou não da mesma. Uma ajuda preciosa, no que se refere à decisão de se realizar um determinado trabalho de conservação, e a do veículo VIV02 EM 120 que faz inspeções ao longo de toda a rede ferroviária e permite recolher dados e classificar através do desvio padrão, troços com extensão de 200 metros, obtendo os dados relevantes sobre a necessidade de intervenção. Para além do referido veículo existem também equipamentos ligeiros de inspecção dos parâmetros geométricos de via. Um desses equipamentos designa-se por Trólei, não sendo motorizado, pois o mesmo é movido manualmente por um operador. Obviamente que este equipamento não faz a inspecção a toda a rede pois a operação de medição é morosa, sendo contudo utilizado para análise de defeitos geométricos em pequenos trocos, tornando-se assim uma mais-valia, evitando o deslocar de um equipamento “pesado” como o VIV 02 EM 120. Para atingir os objectivos deste trabalho realizaram-se testes de medição com ambos (veiculo e equipamento ligeiro), no mesmo espaço temporal e com as mesmas características físicas, como a temperatura, humidade etc. Os resultados, de acordo com os objectivos, são a comparação entre as medições de ambos, com vista a comprovar a sua utilidade e necessidade, de acordo com os vários tipos de superstruturas constituintes da rede ferroviária nacional.

Surge damping analysis in pipe systems: modelling and experiments

The current study focuses on the analysis of pressure surge damping in single pipeline systems generated by a fast change of flow, conditions. A dimensionless form of pressurised transient flow equations was developed. presenting the main advantage of being independent of the system characteristics. In lack of flow velocity profiles. the unsteady friction in turbulent regimes is analysed based on two new empirical corrective-coefficients associated with local and convective acceleration terms. A new, surge damping approach is also presented taking into account the pressure peak time variation. The observed attenuation effect in the pressure wave for high deformable pipe materials can be described by a combination of the non-elastic behaviour of the pipe-wall with steady and unsteady friction effects. Several simulations and experimental tests have been carried out. in order to analyse the dynamic response of single pipelines with different characteristics, such as pipe materials. diameters. thickness. lengths and transient conditions.

Light pollution and energy efficiency: a case study of the village of Vialonga

Since industrialization and the formation of larger urban centers in the nineteenth century, pollution of the environment was always present in daily life in various ways, namely in the form of light. Light pollution can cause various consequences, both for humans and for their ecosystem, producing effects on environmental, social, economic and scientific level. In Portugal, the lighting is responsible for 3% of total electricity consumption, energy costs are in some cases more than 50% towards the costs incurred by municipalities with energy, checking-in recent years a trend similar to that improvement of illumination levels in the region (about 4 to 5% per year). Proper use of lighting brings many benefits both to the citizen and environment, since greater energy efficiency can contribute to reducing CO2 emissions, energy costs, as well as to decrease the use of resources not-renewable and/or contamination of renewable resources, which can occurs in the process of obtaining electricity. The present study has a main goal to analyze the illuminance levels associated to the public lighting of the village of Vialonga, Vila Franca de Xira (Portugal), to verify if it is efficient. The aim is also to relate the efficiency of street lighting with the existence of light pollution.

Two-Higgs-doublet model in light of the standard model H -> tau(+)tau(-) search at the LHC

We study the implications of the searches based on H -> tau(+)tau-by the ATLAS and CMS collaborations on the parameter space of the two-Higgs-doublet model (2HDM). In the 2HDM, the scalars can decay into a tau pair with a branching ratio larger than the SM one, leading to constraints on the 2HDM parameter space. We show that in model II, values of tan beta > 1.8 are definitively excluded if the pseudoscalar is in the mass range 110 GeV < m(A) < 145 GeV. We have also discussed the implications for the 2HDM of the recent dimuon search by the ATLAS collaboration for a CP-odd scalar in the mass range 4-12 GeV.

Análise de desempenho em redes móveis Long Term Evolution (Parceria CELFINET)

A rede móvel Long Term Evolution (LTE) é uma tecnologia que está a ser fortemente implementada, não só em Portugal mas no resto do mundo. A adoção do LTE deve-se em grande parte à maior capacidade e à baixa latência oferecidas, para além de ser expansível ao LTE-Advanced. O trabalho apresentado tem por objetivo a análise do desempenho de uma rede LTE piloto e comparar os resultados com o teoricamente expectável. Foi adotada uma metodologia de planeamento em LTE e comprovada através das medidas empíricas realizadas. Dessas medições são também sugeridos dois novos modelos de propagação para LTE nos 2,6 GHz. Para distâncias inferiores a 1 km sugere-se o modelo LTE-PL. Para distâncias superiores a 1 km foi feita uma adaptação ao modelo Okumura-Hata para que se aproximasse aos resultados obtidos. Das medições efetuadas observou-se que em boas condições rádio, os débitos bináriossão bastante próximos dos máximos teóricos. Além disso foi obtido o desvio padrão em LTE de uma área Urbano Denso de 12 dB. Foi ainda possível definir uma margem para as perdas de penetração in-car de 2,7 dB. Efetuou-se uma análise de vários Key Performance Indicators que permitem avaliar o desempenho do LTE, tendo também sido definidas categorias de qualidade de serviço. Por último foi avaliado o impacto da velocidade e da distância, pelas medidas realizadas.

Semiconductor Device as Optical Demultiplexer for Short Range Optical Communications

In this paper we present results on the use of a multilayered a-SiC:H heterostructure as a wavelength-division demultiplexing device for the visible light spectrum. The proposed device is composed of two stacked p-i-n photodiodes with intrinsic absorber regions adjusted to short and long wavelength absorption and carrier collection. An optoelectronic characterisation of the device was performed in the visible spectrum. Demonstration of the device functionality for WDM applications was done with three different input channels covering the long, the medium and the short wavelengths in the visible range. The recovery of the input channels is explained using the photocurrent spectral dependence on the applied voltage. An electrical model of the WDM device is proposed and supported by the solution of the respective circuit equations. Short range optical communications constitute the major application field, however other applications are also foreseen.

Photodetector with integrated optical thin film filters

This paper reports on optical filters based on a-SiC:H tandem pi'n/pin heterostructures. The spectral sensitivity is analyzed. Steady state optical bias with different wavelengths are applied from each front and back sides and the photocurrent is measured. Results show that it is possible to control the sensitivity of the device and to tune a specific wavelength range by combining radiations with complementary light penetration depths. The transfer characteristics effects due to changes in the front and back optical bias wavelength are discussed. Depending on the wavelength of the external background and irradiation side, the device acts either as a short- or a long-pass band filter or as a band-stop filter. The output waveform presents a nonlinear amplitude-dependent response to the wavelengths of the input channels.

A Voltage Limiter Circuit for Indoor Light Energy Harvesting Applications

A voltage limiter circuit for indoor light energy harvesting applications is presented. This circuit is a part of a bigger system, whose function is to harvest indoor light energy, process it and store it, so that it can be used at a later time. This processing consists on maximum power point tracking (MPPT) and stepping-up, of the voltage from the photovoltaic (PV) harvester cell. The circuit here described, ensures that even under strong illumination, the generated voltage will not exceed the limit allowed by the technology, avoiding the degradation, or destruction, of the integrated die. A prototype of the limiter circuit was designed in a 130 nm CMOS technology. The layout of the circuit has a total area of 23414 mu m(2). Simulation results, using Spectre, are presented.

Light shutters from nanocrystalline cellulose rods in a nematic liquid crystal

This work reports a recently developed electro-optical (EO) device that can potentially be used as a light shutter or a privacy window. By using nanocrystalline cellulose rods, we were able to improve some of the most relevant parameters characterising the EO behaviour. A brief description of the proposed working mechanism for these devices is presented, and numerical simulations based on this mechanism of both the optical transmission and the cells' electrical capacitance are compared with the obtained results, validating the underlying working model considered.

Start-up circuit for low-power indoor light energy harvesting applications

A start-up circuit, used in a micro-power indoor light energy harvesting system, is described. This start-up circuit achieves two goals: first, to produce a reset signal, power-on-reset (POR), for the energy harvesting system, and secondly, to temporarily shunt the output of the photovoltaic (PV) cells, to the output node of the system, which is connected to a capacitor. This capacitor is charged to a suitable value, so that a voltage step-up converter starts operating, thus increasing the output voltage to a larger value than the one provided by the PV cells. A prototype of the circuit was manufactured in a 130 nm CMOS technology, occupying an area of only 0.019 mm(2). Experimental results demonstrate the correct operation of the circuit, being able to correctly start-up the system, even when having an input as low as 390 mV using, in this case, an estimated energy of only 5.3 pJ to produce the start-up.

Optical demultiplexer based on an a-SiC:H voltage controlled device

In this paper we present results on the use of a semiconductor heterostructure based on a-SiC:H as a wavelength-division demultiplexer for the visible light spectrum. The proposed device is composed of two stacked p-i-n photodiodes with intrinsic absorber regions adjusted to short and long wavelength absorption and carrier collection. An optoelectronic characterisation of the device was performed in the visible spectrum. Demonstration of the device functionality for WDM applications was done with three different input channels covering the long, the medium and the short wavelengths in the visible range. The recovery of the input channels is explained using the photocurrent spectral dependence on the applied voltage. An electrical model of the WDM device is proposed and supported by the solution of the respective circuit equations. Short range optical communications constitute the major application field however other applications are foreseen. (C) 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.