Design of a new test chamber for evaluation of the toxicity of rubber infill

A test chamber was projected and built (according to ISO 16000-9 Standard) to simulate atmospheric conditions experienced by rubber infill (when applied in synthetic turf pitches) and measure accurately the airborne emissions of pollutants such as dusts and volatile organic compounds (VOC), as well as pollutants present in leachates. It should be pointed out that standard ISO 16000-9 is only concerned with the determination of the emission of VOC from building products and furnishing (not specific of synthetic turf materials), whereas other standards are concerned with the emission of leachates only. This procedure is to be considered as a technical option to the lysimeter "global turf system evaluation" when the rubber infill alone is to be evaluated. The advantage of the proposed option considering this "test chamber" is its simplicity and economy. This test chamber is actually installed and being used for tests in LAIST.

Design and optimization of na ultra wideband and compact microwave antenna for radiometric monitoring of brain temperature

We present the modeling efforts on antenna design and frequency selection to monitor brain temperature during prolonged surgery using noninvasive microwave radiometry. A tapered log-spiral antenna design is chosen for its wideband characteristics that allow higher power collection from deep brain. Parametric analysis with the software HFSS is used to optimize antenna performance for deep brain temperature sensing. Radiometric antenna efficiency (eta) is evaluated in terms of the ratio of power collected from brain to total power received by the antenna. Anatomical information extracted from several adult computed tomography scans is used to establish design parameters for constructing an accurate layered 3-D tissue phantom. This head phantom includes separate brain and scalp regions, with tissue equivalent liquids circulating at independent temperatures on either side of an intact skull. The optimized frequency band is 1.1-1.6 GHz producing an average antenna efficiency of 50.3% from a two turn log-spiral antenna. The entire sensor package is contained in a lightweight and low-profile 2.8 cm diameter by 1.5 cm high assembly that can be held in place over the skin with an electromagnetic interference shielding adhesive patch. The calculated radiometric equivalent brain temperature tracks within 0.4 degrees C of the measured brain phantom temperature when the brain phantom is lowered 10. C and then returned to the original temperature (37 degrees C) over a 4.6-h experiment. The numerical and experimental results demonstrate that the optimized 2.5-cm log-spiral antenna is well suited for the noninvasive radiometric sensing of deep brain temperature.

O design do manual escolar

O manual escolar, pelas suas características, é um produto de design gráfico, disciplina que tardou a desenvolver-se em Portugal. Após o 25 de Abril, as editoras escolares expandiram-se, e a globalização do ensino teve como consequência o aumento do número de manuais escolares. O desenvolvimento do design gráfico está intimamente ligado ao desenvolvimento da tecnologia informática, contribuindo fortemente para a alteração das características do manual escolar, sendo a mais notória a importância dada à imagem como portadora de informação. Sem investigação que suporte o seu actual formato, nem formação dos professores que permita explorar as suas novas potencialidades, interrogamo-nos sobre a sua eficácia. O campo da teoria da imagem é vasto e a sua aplicação, quer na realização, quer na exploração pedagógica do manual escolar, exige alguma sistematização que procuramos apresentar.

Design of improved rail-to-rail low-distortion and low-stress switches in advanced CMOS technologies

This paper describes the efficient design of an improved and dedicated switched-capacitor (SC) circuit capable of linearizing CMOS switches to allow SC circuits to reach low distortion levels. The described circuit (SC linearization control circuit, SLC) has the advantage over conventional clock-bootstrapping circuits of exhibiting low-stress, since large gate voltages are avoided. This paper presents exhaustive corner simulation results of a SC sample-and-hold (S/H) circuit which employs the proposed and optimized circuits, together with the experimental evaluation of a complete 10-bit ADC utilizing the referred S/H circuit. These results show that the SLC circuits can reduce distortion and increase dynamic linearity above 12 bits for wide input signal bandwidths.

Optimal design of piezolaminated structures using B-spline strip finite element models

A package of B-spline finite strip models is developed for the linear analysis of piezolaminated plates and shells. This package is associated to a global optimization technique in order to enhance the performance of these types of structures, subjected to various types of objective functions and/or constraints, with discrete and continuous design variables. The models considered are based on a higher-order displacement field and one can apply them to the static, free vibration and buckling analyses of laminated adaptive structures with arbitrary lay-ups, loading and boundary conditions. Genetic algorithms, with either binary or floating point encoding of design variables, were considered to find optimal locations of piezoelectric actuators as well as to determine the best voltages applied to them in order to obtain a desired structure shape. These models provide an overall economy of computing effort for static and vibration problems.

Active and passive behaviors of soft tissues: Pelvic floor muscles

: A new active-contraction visco-elastic numerical model of the pelvic floor (skeletal) muscle is presented. Our model includes all elements that represent the muscle constitutive behavior, contraction and relaxation. In contrast with the previous models, the activation function can be null. The complete equations are shown and exactly linearized. Small verification and validation tests are performed and the pelvis is modeled using the data from the intra-abdominal pressure tests

Concepção de uma pequena turbina eólica destinada ao segmento doméstico (simplificação e análise aerodinâmica das pás)

O trabalho que se apresenta incide sobre o estudo aerodinâmico das pás de uma turbina eólica de pequeno porte, com vista à simplificação geométrica, de forma a que estas sejam baratas e de fácil concepção. A teoria da quantidade de movimento do elemento de pá (BEMT), que é o modelo de referência para o projecto e análise aerodinâmica das pás das turbinas eólicas, foi utilizada neste trabalho de forma a projectar e analisar aerodinamicamente as pás da turbina. Sendo assim, desenvolveu-se um programa computacional em MATLAB, denominado de “Turbina”, de forma a implementar a teoria BEM. Introduzindo os dados dos parâmetros de projecto no programa (potência requerida, o número de pás, velocidade do vento, a TSR e o tipo de perfil alar), obtêm-se os parâmetros geométricos das pás (distribuição da corda ao longo da envergadura, o raio da pá e a distribuição da torção da pá), os parâmetros aerodinâmicos e de desempenho. Uma pá ideal foi calculada e de seguida foi modificada de forma a obter-se uma pá simples e menos carregada aerodinamicamente. Introduzidas as modificações na geometria da pá ideal, obtiveram-se duas configurações distintas. Uma configuração linear, onde a distribuição da corda e do ângulo de torção se tornam lineares, e outra configuração bi-linear, onde a distribuição da corda continua linear mas o ângulo de torção se torna bi-linear, isto é, a pá é composta por dois troços onde cada troço apresenta uma distribuição linear do ângulo de torção geométrica. As conclusões demonstram que a configuração bi-linear é uma boa alternativa a configuração ideal, apresentando uma redução do desempenho do rotor de 2.8% para um aumento do raio da pá em 1.41%, para se obter a mesma potência da configuração ideal. A análise aos perfis alares, utilizados neste trabalho, foi efectuada a partir dos programas comerciais ICEM e FLUENT. De forma a automatizar a análise de CFD, três programas foram desenvolvidos utilizando a linguagem de programação “C”. Os programas são denominados de “Malha2D”, “Calcula_Coeficientes” e “Plot_Graficos”. Finalmente, um estudo paramétrico foi feito de forma a avaliar a influências das variáveis de projecto no desempenho geral da turbina.

Projecto de execução da passagem superior 9A, na concessão Douro Litoral na A32/IC2 - Oliveira de Azeméis/IP1 (S. Lourenço)

O presente trabalho teve como principal objectivo a aplicação dos conceitos adquiridos nas unidades curriculares da licenciatura e do mestrado. Nesse sentido tomou-se a opção da realização de um projecto de execução de uma obra de arte para o trabalho final de mestrado, realizado num conceituado gabinete de projecto de pontes e viadutos, com vista à obtenção do grau de mestre. O projecto refere-se a uma obra de arte que se insere num nó rodoviário de ligação entre duas auto-estradas que, dados os seus condicionamentos de perfil, quer longitudinal quer transversal, e implantação no local, pode ser considerada uma obra de arte especial. O processo de análise foi feito com recurso ao programa de cálculo automático SAP2000®, tendo em conta os regulamentos nacionais aplicáveis a estruturas de pontes e os Eurocódigos em fase de implementação em Portugal. O projecto de execução, objecto deste trabalho, foi realizado em função de uma metodologia de construção simples, que é o recurso à utilização, por fases, de cimbres apoiados no solo. A optimização das fases de construção é um factor condicionante na análise e concepção da obra de arte deste projecto, pelo que se procura obter uma relação optimizada entre o rendimento de construção e o funcionamento estrutural da obra de arte, de forma a garantir a segurança da estrutura e o conforto dos utilizadores a longo prazo.

Design of a sea-level tsunami detection network for the Gulf of Cadiz

The devastating impact of the Sumatra tsunami of 26 December 2004, raised the question for scientists of how to forecast a tsunami threat. In 2005, the IOC-UNESCO XXIII assembly decided to implement a global tsunami warning system to cover the regions that were not yet protected, namely the Indian Ocean, the Caribbean and the North East Atlantic, the Mediterranean and connected seas (the NEAM region). Within NEAM, the Gulf of Cadiz is the more sensitive area, with an important record of devastating historical events. The objective of this paper is to present a preliminary design for a reliable tsunami detection network for the Gulf of Cadiz, based on a network of sea-level observatories. The tsunamigenic potential of this region has been revised in order to define the active tectonic structures. Tsunami hydrodynamic modeling and GIS technology have been used to identify the appropriate locations for the minimum number of sea-level stations. Results show that 3 tsunameters are required as the minimum number of stations necessary to assure an acceptable protection to the large coastal population in the Gulf of Cadiz. In addition, 29 tide gauge stations could be necessary to fully assess the effects of a tsunami along the affected coasts of Portugal, Spain and Morocco.

MDAI: Model based Design in Automobile Industry

It is proposed a new approach based on a methodology, assisted by a tool, to create new products in the automobile industry based on previous defined processes and experiences inspired on a set of best practices or principles: it is based on high-level models or specifications; it is component-based architecture centric; it is based on generative programming techniques. This approach follows in essence the MDA (Model Driven Architecture) philosophy with some specific characteristics. We propose a repository that keeps related information, such as models, applications, design information, generated artifacts and even information concerning the development process itself (e.g., generation steps, tests and integration milestones). Generically, this methodology receives the users' requirements to a new product (e.g., functional, non-functional, product specification) as its main inputs and produces a set of artifacts (e.g., design parts, process validation output) as its main output, that will be integrated in the engineer design tool (e.g. CAD system) facilitating the work.

New Steel Alloys for the Design of Heat Recovery Steam Generator Components of Combined Cycle Gas Plants

Demand for power is growing every day, mainly due to emerging economies in countries such as China, Russia, India, and Brazil. During the last 50 years steam pressure and temperature in power plants have been continuously raised to improve thermal efficiency. Recent efforts to improve efficiency leads to the development of a new generation of heat recovery steam generator, where the Benson once-through technology is applied to improve the thermal efficiency. The main purpose of this paper is to analyze the mechanical behavior of a high pressure superheater manifold by applying finite element modeling and a finite element analysis with the objective of analyzing stress propagation, leading to the study of damage mechanism, e.g., uniaxial fatigue, uniaxial creep for life prediction. The objective of this paper is also to analyze the mechanical properties of the new high temperature resistant materials in the market such as 2Cr Bainitic steels (T/P23 and T/P24) and also the 9-12Cr Martensitic steels (T/P91, T/P92, E911, and P/T122). For this study the design rules for construction of power boilers to define the geometry of the HPSH manifold were applied.

Viability of Two New Mixture Design Methodologies for Self-Consolidating Concrete

This paper presents the results from an experimental study of the technical viability of two mixture designs for self-consolidating concrete (SCC) proposed by two Portuguese researchers in a previous work. The objective was to find the best method to provide the required characteristics of SCC in fresh and hardened states without having to experiment with a large number of mixtures. Five SCC mixtures, each with a volume of 25 L (6.61 gal.) were prepared using a forced mixer with a vertical axis for each of three compressive strength targets: 40, 55, and 70 MPa (5.80, 7.98, and 10.15 ksi). The mixtures' fresh state properties of fluidity, segregation resistance ability, and bleeding and blockage tendency, and their hardened state property of compressive strength were compared. For this study, the following tests were performed. slump-flow, V-funnel, L-box, box, and compressive strength. The results of this study made it possible to identify the most influential factors in the design of the SCC mixtures.

A utilização da madeira na construção de edifícios: alternativas às soluções tradicionais

Esta dissertação insere-se num projecto de investigação relacionado com o papel que a madeira apresenta na construção nos tempos de hoje, necessário para obtenção do Mestrado em Engenharia Civil. A madeira apresenta, enquanto material de construção, especificidades únicas: é um material orgânico, ao contrário da pedra, do aço e do betão; é um material combustível, sem que isto implique necessariamente uma baixa resistência ao fogo; é um material tradicional, presente em pavimentos e coberturas de edifícios antigos e é, paradoxalmente, um material novo, adoptado em arrojadas obras de arquitectura contemporânea. Estas características, associadas à necessidade de garantir a sustentabilidade da construção e de conservar e reabilitar o património edificado, tornam essencial o estudo das propriedades mecânicas do material, dos seus processos de degradação química e biológica, dos meios de protecção e do comportamento de elementos estruturais ao fogo. As estruturas em madeira têm tido uma procura crescente no nosso país, revelando-se uma opção interessante, como alternativa a estruturas de aço ou de betão. No entanto, por configurarem ainda soluções estruturais, materiais e processos construtivos pouco comuns entre nós, considera-se que não estão suficientemente divulgados os instrumentos de que podemos e devemos dispor para a garantia da qualidade destas estruturas. É apresentado um estudo de viabilidade económica no âmbito do nosso país, comparando casas em madeira, modulares pré-fabricadas, com casas cuja construção é feita em alvenaria e betão armado, de forma a poder comparar os custos para ambas as soluções construtivas. Para tal, foram realizadas visitas a empresas, fábricas e a obras com o objectivo de entender como funciona o processo de fabrico de uma casa pré-fabricada em madeira.

A soft origin for CKM-type CP violation

We present a two-Higgs-doublet model, with a Z(3) symmetry, in which CP violation originates solely in a soft (dimension-2) coupling in the scalar potential, and reveals itself solely in the CKM (quark mixing) matrix. In particular, in the mass basis the Yukawa interactions of the neutral scalars are all real. The model has only eleven parameters to fit the six quark masses and the four independent CKM-matrix observables. We find regions of parameter space in which the flavour-changing neutral couplings are so suppressed that they allow the scalars to be no heavier than a few hundred GeV. (C) 2011 Elsevier B.V. All rights reserved.

Optical Filter Design Using Background Wavelength Processing Techniques

Amorphous SiC tandem heterostructures are used to filter a specific band, in the visible range. Experimental and simulated results are compared to validate the use of SiC multilayered structures in applications where gain compensation is needed or to attenuate unwanted wavelengths. Spectral response data acquired under different frequencies, optical wavelength control and side irradiations are analyzed. Transfer function characteristics are discussed. Color pulsed communication channels are transmitted together and the output signal analyzed under different background conditions. Results show that under controlled wavelength backgrounds, the device sensitivity is enhanced in a precise wavelength range and quenched in the others, tuning or suppressing a specific band. Depending on the background wavelength and irradiation side, the device acts either as a long-, a short-, or a band-rejection pass filter. An optoelectronic model supports the experimental results and gives insight on the physics of the device.