Destruction of the tar present in syngas by combustion in porous media

The cleaning of syngas is one of the most important challenges in the development of technologies based on gasification of biomass. Tar is an undesired byproduct because, once condensed, it can cause fouling and plugging and damage the downstream equipment. Thermochemical methods for tar destruction, which include catalytic cracking and thermal cracking, are intrinsically attractive because they are energetically efficient and no movable parts are required nor byproducts are produced. The main difficulty with these methods is the tendency for tar to polymerize at high temperatures. An alternative to tar removal is the complete combustion of the syngas in a porous burner directly as it leaves the particle capture system. In this context, the main aim of this study is to evaluate the destruction of the tar present in the syngas from biomass gasification by combustion in porous media. A gas mixture was used to emulate the syngas, which included toluene as a tar surrogate. Initially, CHEMKIN was used to assess the potential of the proposed solution. The calculations revealed the complete destruction of the tar surrogate for a wide range of operating conditions and indicated that the most important reactions in the toluene conversion are C6H5CH3 + OH <-> C6H5CH2 + H2O, C6H5CH3 + OH <-> C6H4CH3 + H2O, and C6H5CH3 + O <-> OC6H4CH3 + H and that the formation of toluene can occur through C6H5CH2 + H <-> C6H5CH3. Subsequently, experimental tests were performed in a porous burner fired with pure methane and syngas for two equivalence ratios and three flow velocities. In these tests, the toluene concentration in the syngas varied from 50 to 200 g/Nm(3). In line with the CHEMKIN calculations, the results revealed that toluene was almost completely destroyed for all tested conditions and that the process did not affect the performance of the porous burner regarding the emissions of CO, hydrocarbons, and NOx.

Low-Carbon Cement with Waste Oil-Cracking Catalyst Incorporation

The present paper shows preliminary results of an ongoing project which one of the goals is to investigate the viability of using waste FCC catalyst (wFCC), originated from Portuguese oil refinery, to produce low carbon blended cements. For this purpose, four blended cements were produced by substituting cement CEM I 42.5R up to 20% (w/w) by waste FCC catalyst. Initial and final setting times, consistency of standard paste, soundness and compressive strengths after 2, 7 and 28 days were measured. It was observed that the wFCC blended cements developed similar strength, at 28 days, compared to the reference cement, CEM I 42.5R. Moreover, cements with waste FCC catalyst incorporation up to 15% w/w meet European Standard EN 197-1 specifications for CEM II/A type cement, in the 42.5R strength class.

Efeito da moagem do catalisador exausto de cracking catalítico nas propriedade de argamassas de cimento

Atualmente, o impacto ambiental gerado pela produção de cimento é uma das grandes preocupações a nível mundial. O seu processo de produção requer não só a utilização de quantidades significativas de recursos naturais não renováveis bem como de consumo de energia. Concomitantemente, a produção de cimento é a maior fonte de emissão antropogénica de CO2 para a atmosfera. Desta forma, várias medidas têm sido concebidas com o intuito de diminuir estes impactos visando a preservação do meio ambiente. Uma dessas medidas consiste em substituir parcialmente cimento por resíduos industriais. Neste sentido, com o presente trabalho pretendeu-se avaliar o efeito da moagem do catalisador exausto da unidade de “cracking” catalítico (FCC) - proveniente da refinaria da GALP, em Sines - nas propriedades de argamassas em que este resíduo substitui parcialmente o cimento. Na campanha experimental prepararam-se argamassas com substituição parcial de cimento por resíduo de FCC – entre os 0 a 15%, em massa – com três distribuições de tamanho de partículas de resíduo distintas. Na preparação destas argamassas adotaram-se duas abordagens experimentais que originaram duas séries de argamassas: numa das séries, a consistência das argamassas no estado fresco varia em função do teor de catalisador incorporado e na outra série, a consistência das argamassas é mantida constante através da adição de superplastificante, independentemente do teor de catalisador incorporado. As propriedades das argamassas no estado fresco avaliadas foram: a consistência por espalhamento, o teor de ar e a massa volúmica. No estado endurecido avaliou-se: a velocidade de propagação de ondas ultrassónicas nas argamassas, a resistência mecânica, a aderência e a absorção de água por capilaridade. Com o presente estudo verifica-se que a utilização de resíduo moído como substituto parcial do cimento, aumenta a trabalhabilidade da argamassa para substituições de 15%. Para substituições de 5% e 10%, a moagem do resíduo não se apresenta sensível à trabalhabilidade. A moagem deste resíduo de FCC também não tem um efeito significativo nos valores de resistência à compressão das argamassas em que é incorporado, embora se verifique uma tendência para que os resíduos moídos conduzam a valores resistência à compressão mais elevados quando comparado com o não moído, particularmente quando a percentagem de incorporação do resíduo é mais elevada. A atividade pozolânica aumenta com a moagem do resíduo de FCC. A introdução de resíduo moído conduz à diminuição da absorção de água por capilaridade, à medida que a percentagem de substituição aumenta.

Thermal Residual Stresses in Functionally Graded Structures: a Didactic Case Study

Conferência: 2nd Experiment at International Conference - 18-20 September 2013

Distributed MPC for Thermal Comfort and Load Allocation with Energy Auction

This paper presents a distributed predictive control methodology for indoor thermal comfort that optimizes the consumption of a limited shared energy resource using an integrated demand-side management approach that involves a power price auction and an appliance loads allocation scheme. The control objective for each subsystem (house or building) aims to minimize the energy cost while maintaining the indoor temperature inside comfort limits. In a distributed coordinated multi-agent ecosystem, each house or building control agent achieves its objectives while sharing, among them, the available energy through the introduction of particular coupling constraints in their underlying optimization problem. Coordination is maintained by a daily green energy auction bring in a demand-side management approach. Also the implemented distributed MPC algorithm is described and validated with simulation studies.

Renewable power forecast to scheduling of thermal units

In this work is discussed the importance of the renewable production forecast in an island environment. A probabilistic forecast based on kernel density estimators is proposed. The aggregation of these forecasts, allows the determination of thermal generation amount needed to schedule and operating a power grid of an island with high penetration of renewable generation. A case study based on electric system of S. Miguel Island is presented. The results show that the forecast techniques are an imperative tool help the grid management.

Self-scheduling and bidding strategies of thermal units with stochastic emission constraints

This paper is on the self-scheduling problem for a thermal power producer taking part in a pool-based electricity market as a price-taker, having bilateral contracts and emission-constrained. An approach based on stochastic mixed-integer linear programming approach is proposed for solving the self-scheduling problem. Uncertainty regarding electricity price is considered through a set of scenarios computed by simulation and scenario-reduction. Thermal units are modelled by variable costs, start-up costs and technical operating constraints, such as: forbidden operating zones, ramp up/down limits and minimum up/down time limits. A requirement on emission allowances to mitigate carbon footprint is modelled by a stochastic constraint. Supply functions for different emission allowance levels are accessed in order to establish the optimal bidding strategy. A case study is presented to illustrate the usefulness and the proficiency of the proposed approach in supporting biding strategies. (C) 2014 Elsevier Ltd. All rights reserved.

Research progress on reuse of fluid catalytic cracking waste from oil refinery in cement-based materials

Present paper present the main results obtained in the scope of an ongoing project which aims to contribute to the valorization of a waste generated by the Portuguese oil company in construction materials. This waste is an aluminosilicate with high pozzolanic reactivity. Several different technological applications had already been tested with success both in terms of properties and compliance with the corresponding standards specifications. Namely, this project results already demonstrated that this waste can be used in traditional concrete, self-compacted concrete, mortars (renders, masonry mortar, concrete repair mortars), cement main constituent as well as alkali activated binders.