The effect of metal transfer stability (spattering) on fume generation, morphology and composition in short-circuit MAG welding

The main objective of this work was to evaluate the hypothesis that the greater transfer stability leads also to less volume of fumes. Using an Ar + 25%CO2 blend as shielding gas and maintaining constant the average current, wire feed speed and welding speed, bead-on-plate welds were carried out with plain carbon steel solid wire. The welding voltage was scanned to progressively vary the transfer stability. Using two conditions of low stability and one with high stability, fume generation was evaluated by means of the AWS F1.2:2006 standard. The influence of these conditions on fume morphology and composition was also verified. A condition with greater transfer stability does not generate less fume quantity, despite the fact that this condition produces fewer spatters. Other factors such as short-circuit current, arcing time, droplet diameters and arc length are the likely governing factors, but in an interrelated way. Metal transfer stability does not influence either the composition or the size/morphology of fume particulates. (c) 2014 Elsevier B.V. All rights reserved.

Pt/Carbon materials as Bi-Functional catalysts for N-decane hydroisomerization

The activity and selectivity of bi-functional carbon-supported platinum catalysts for the hydroisomerization of n-alkanes have been studied. The influence of the properties of the carbon support on the performance of the catalysts were investigated by incorporating the metallic function on a series of carbons with varied porosity (microporous: GL-50 from Norit, and mesoporous: CMK-3) and surface chemistry (modified by wet oxidation). The characterization results achieved with H-2 chemisorption and TEM showed differences in surface metal concentrations and metal-support interactions depending on the support composition. The highest metal dispersion was achieved after oxidation of the carbon matrix in concentrated nitric acid, suggesting that the presence of surface functional sites distributed in inner and outer surface favors a homogeneous metal distribution. On the other hand, the higher hydrogenating activity of the catalysts prepared with the mesoporous carbon pointed out that a fast molecular traffic inside the pores plays an important role in the catalysts performance. For n-decane hydroisomerization of long chain n-alkanes, higher activities were obtained for the catalysts with an optimized acidity and metal dispersion along with adequate porosity, pointing out the importance of the support properties in the performance of the catalysts.

Experimental study of the mechanical properties and durability of self-compacting mortars with nano materials (SiO2 and TiO2)

Resumo: Cement, as well as the remaining constituents of self-compacting mortars, must be carefully selected, in order to obtain an adequate composition with a granular mix as compact as possible and a good performance in the fresh state (self-compacting effect) and the hardened state (mechanical and durability-related behavior). Therefore in this work the possibility of incorporating nano particles in self-compacting mortars was studied. Nano materials are very reactive due mostly to their high specific surface and show a great potential to improve the properties of these mortars, both in mechanical and durability terms. In this work two nano materials were used, nano silica (nano SiO2) in colloidal state and nano titanium (nano TiO2) in amorphous state, in two types of self-compacting mortars (ratio binder:sand of 1:1 and 1:2). The self-compacting mortar mixes have the same water/cement ratio and 30% of replacement of cement with fly ashes. The influence of nano materials nano-SiO2 and nano-TiO2 on the fresh and hardened state properties of these self-compacting mortars was studied. The results show that the use of nano materials in repair and rehabilitation mortars has significant potential but still needs to be optimized. (C) 2015 Elsevier Ltd. All rights reserved.

Rheological behaviour of concrete made with fine recycled concrete aggregates - Influence of the superplasticizer

This paper evaluates the influence of two superplasticizers (SP) on the rheological behaviour of concrete made with fine recycled concrete aggregates (FRCA). Three families of concrete were tested: family CO made without SP, family Cl made with a regular superplasticizer and family C2 made with a high-performance superplasticizer. Five replacement ratios of natural sand by FRCA were tested: 0%, 10%, 30%, 50% and 100%. The coarse aggregates were natural gravels. Three criteria were established to design the concrete mixes' composition: keep the same particle size distribution curves, adjust the water/cement ratio to obtain a similar slump and no pre-saturation of the FRCA. All mixes had the same cement and SP content. The results show that the incorporation of FRCA significantly increased the shrinkage and creep deformation. The FRCA's effect was influenced by the curing age. The reference concrete made with natural sand stabilizes the creep deformation faster than the mixes made with FRCA. The incorporation of superplasticizer increased the shrinkage at early ages and decreased the shrinkage at 91 days of age. The regular superplasticizer did not improve the creep deformation while the high-performance superplasticizer highly improved this property. The incorporation of FRCA jeopardized the SP's effectiveness. This study demonstrated that to use FRCA and superplasticizer for concrete production it is necessary to take into account the different rheological behaviour of these mixes. (C) 2015 Elsevier Ltd. All rights reserved.

Body composition, muscle strength, functional capacity, and physical disability risk in liver transplanted familial amyloidotic polyneuropathy patients

Abstract: Background: Familial amyloidotic polyneuropathy (FAP) is a neurodegenerative disease leading to sensory and motor polyneuropathies, and functional limitations. Liver transplantation is the only treatment for FAP, requiring medication that negatively affects bone and muscle metabolism. The aim of this study was to compare body composition, levels of specific strength, level of physical disability risk, and functional capacity of transplanted FAP patients (FAPTx) with a group of healthy individuals (CON). Methods: A group of patients with 48 FAPTx (28 men, 20 women) was compared with 24 CON individuals (14 men, 10 women). Body composition was assessed by dual-energy X-ray absorptiometry, and total skeletal muscle mass (TBSMM) and skeletal muscle index (SMI) were calculated. Handgrip strength was measured for both hands as was isometric strength of quadriceps. Muscle quality (MQ) was ascertained by the ratio of strength to muscle mass. Functional capacity was assessed by the six-minute walk test. Results: Patients with FAPTx had significantly lower functional capacity, weight, body mass index, total fat mass, TBSMM, SMI, lean mass, muscle strength, MQ, and bone mineral density. Conclusion: Patients with FAPTx appear to be at particularly high risk of functional disability, suggesting an important role for an early and appropriately designed rehabilitation program.

Effects of a randomized trial of exercise on body composition of liver transplanted patients

Liver transplantation is used as a only therapy so far, that stop the progression of some aspects of familial amyloidotic polyneuropathy disease (FAP) an autossomic neurodegenerative disease. FAP often results in severe functional limitations. Transplantation requires aggressive medication which impairs bone and muscle metabolism. Malnutrition plus weight loss is already one feature of FAP patients. All this may produce negative consequences on body composition. The effect of exercise training in FAP patients after a liver transplant (FAPTX) is currently unknown. The purpose of this study is to evaluate the effects of a six months exercise training program on body composition in FAPTX patients.

Templated synthesis of carbon materials mediated by porous clay heterostructures

Mesoporous carbon materials were prepared through template method approach using porous clay heterostructures (PCHs) as matrix and furfuryl alcohol as carbon precursor. Three PCHs prepared using amines with 8, 10 and 12 carbon atoms were used. The effect of several impregnation-polymerization cycles of the carbon precursor, the carbonization temperature and the need of a previous surface alumination were evaluated. The presence of two porosity domains was identified in all the carbon materials. These two domains comprise pores resulting from the carbonization of the polymer film formed in the inner structure of the PCH (domain I) and larger pores created by the clay particles aggregation (domain II). The predominance of the porosity associated to domain I or II can be achieved by choosing a specific amine to prepare the PCH matrix. Carbonization at 700 C led to the highest development of pores of domain I. In general, the second impregnation-polymerization cycle of furfuryl alcohol resulted in a small decrease of both types of porosity domains. Furthermore the previous acidification of the surface to create acidic sites proved to be unnecessary. The results showed the potential of PCHs as matrices to tailor the textural properties of carbons prepared by template mediated synthesis.

Composition and antioxidant activity of thymus vulgaris volatiles: comparison between supercritical fluid extraction and hydrodistillation

Supercritical fluid extraction (SEE) of the volatile oil from Thymus vulgaris L. aerial flowering parts was performed under different conditions of pressure, temperature, mean particle size and CO2 flow rate and the correspondent yield and composition were compared with those of the essential oil isolated by hydrodistillation (HD). Both the oils were analyzed by GC and GC-MS and 52 components were identified. The main volatile components obtained were p-cymene (10.0-42.6% for SFE and 28.9-34.8% for HD), gamma-terpinene (0.8-6.9% for SFE and 5.1-7.0% for HD), linalool (2.3-5.3% for SFE and 2.8-3.1% for HD), thymol (19.5-40.8% for SFE and 35.4-41.6% for HD), and carvacrol (1.4-3.1% for SFE and 2.6-3.1% for HD). The main difference was found to be the relative percentage of thymoquinone (not found in the essential oil) and carvacryl methyl ether (1.0-1.2% for HD versus t-0.4 for SFE) which can explain the higher antioxidant activity, assessed by Rancimat test, of the SFE volatiles when compared with HD. Thymoquinone is considered a strong antioxidant compound.

Essential oils of Origanum vulgare L. subsp glandulosum (Desf.) letswaart from Tunisia: chemical composition and antioxidant activity

BACKGROUND: Characterisation of the essential oils from O. glandulosum collected in three locations of Tunisia, chemical composition and the evaluation of their antioxidant activities were carried out. RESULTS: The essential oils from Origanum vulgare L. subsp. glandulosum (Desf.) letswaart collected from three localities of north Tunisia - Krib, Bargou and Nefza - were obtained in yields of 2.5, 3.0 and 4.6% (v/w), respectively. The essential oils were analysed by GC and GC/MS and assayed for their total phenolics content, by the Folin-Ciocalteu method, and antioxidant effectiveness, using the 2,2-diphenyl-1-picrylhydrazil (DPPH) radical scavenging assay. The main components of these essential oils, from Nefza, Bargou and Krib, were p-cymene (36%, 40% and 46%), thymol (32%, 39% and 18%), gamma-terpinene (24%, 12% and 16%) and carvacrol (2%, 2% and 15%), respectively). The ability to scavenge the DPPH radicals, expressed by IC50, ranged from 59 to 80 mg L-1. The total phenolic content, expressed in gallic acid equivalent (GAE) g kg(-1) dry weight, varied from 9.37 to 17.70 g kg(-1) dw. CONCLUSIONS: A correlation was identified between the total phenolic content of the essential oils and DPPH radical scavenger capacity. The occurrence of a p-cymene chemotype of O. glandulosum in the northern region of Tunisia is demonstrated.

Influence of LPG composition on straw applied one componente PU winter foam

O principal objectivo desta tese é obter uma relação directa entre a composição dos gases liquefeitos de petróleo (GLP), propano, n-butano e isobutano, usados como aerossóis propulsores numa lata de poliuretano de um componente, com as propriedades das espumas produzidas por spray. As espumas obtidas, terão de ter como requisito principal, um bom desempenho a temperaturas baixas, -10ºC, sendo por isso designadas por espumas de Inverno. Uma espuma é considerada como tendo um bom desempenho se não apresentar a -10/-10ºC (temperatura lata/ spray) glass bubbles, base holes e cell collapse. As espumas deverão ainda ter densidades do spray no molde a +23/+23ºC abaixo dos 30 g/L, um rendimento superior a 30 L, boa estabilidade dimensional e um caudal de espuma a +5/+5ºC superior a 5 g/s. Os ensaios experimentais foram realizados a +23/+23ºC, +5/+5ºC e a -10/-10ºC. A cada temperatura, as espumas desenvolvidas, foram submetidas a testes que permitiram determinar a sua qualidade. Testes esses que incluem os designados por Quick Tests (QT): o spray no papel e no molde das espumas nas referidas temperaturas. As amostras do papel e no molde são especialmente analisadas, quanto, às glass bubbles, cell collapse, base holes, cell structur e, cutting shrinkage, para além de outras propriedades. Os QT também incluem a análise da densidade no molde (ODM) e o estudo do caudal de espumas. Além dos QT foram realizados os testes da estabilidade dimensional das espumas, testes físicos de compressão e adesão, testes de expansão das espumas após spray e do rendimento por lata de espuma. Em todos os ensaios foi utilizado um tubo adaptador colocado na válvula da lata como método de spray e ainda mantida constante a proporção das matérias-primas (excepto os gases, em estudo). As experiências iniciaram-se com o estudo de GLPs presentes no mercado de aerossóis. Estes resultaram que o GLP: propano/ n-butano/ isobutano: (30/ 0/ 70 w/w%), produz as melhores espumas de inverno a -10/-10ºC, reduzindo desta forma as glass bubbles, base holes e o cell collapse produzido pelos restantes GLP usados como aerossóis nas latas de poliuretano. Testes posteriores tiveram como objectivo estudar a influência directa de cada gás, propano, n-butano e isobutano nas espumas. Para tal, foram usadas duas referências do estudo com GLP comercializáveis, 7396 (30 /0 /70 w/w %) e 7442 (0/ 0/ 100 w/w %). Com estes resultados concluí-se que o n-butano produz más propriedades nas espumas a -10/- 10ºC, formando grandes quantidades de glass bubbles, base holes e cell collapse. Contudo, o uso de propano reduz essas glass bubbles, mas em contrapartida, forma cell collapse.Isobutano, porém diminui o cell collapse mas não as glass bubbles. Dos resultados experimentais podemos constatar que o caudal a +5/+5ºC e densidade das espumas a +23/+23ºC, são influenciados pela composição do GLP. O propano e n-butano aumentam o caudal de espuma das latas e a sua densidade, ao contrário com o que acontece com o isobutano. Todavia, pelos resultados obtidos, o isobutano proporciona os melhores rendimentos de espumas por lata. Podemos concluir que os GLPs que contivessem cerca de 30 w/w % de propano (bons caudais a +5/+5ºC e menos glass bubbles a -10/-10ºC), e cerca 70 w/w % de isobutano (bons rendimentos de espumas, bem como menos cell collapse a -10/-10ºC) produziam as melhores espumas. Também foram desenvolvidos testes sobre a influência da quantidade de gás GLP presente numa lata. A análise do volume de GLP usado, foi realizada com base na melhor espuma obtida nos estudos anteriores, 7396, com um GLP (30 / 0/ 70 w/w%), e foram feitas alterações ao seu volume gás GLP presente no pré-polímero. O estudo concluiu, que o aumento do volume pode diminuir a densidade das espumas, e o seu decréscimo, um aumento da densidade. Também indico u que um mau ajuste do volume poderá causar más propriedades nas espumas. A análise económica, concluiu que o custo das espumas com mais GLP nas suas formulações, reduz-se em cerca de 3%, a quando de um aumento do volume de GLP no pré-polímero de cerca de 8 %. Esta diminuição de custos deveu-se ao facto, de um aumento de volume de gás, implicar uma diminuição na quantidade das restantes matérias-primas, com custos superiores, já que o volume útil total da lata terá de ser sempre mantido nos 750 mL. Com o objectivo de melhorar a qualidade da espuma 7396 (30/0/70 w/w %) obtida nos ensaios anteriores adicionou-se à formulação 7396 o HFC-152a (1,1-di fluoroetano). Os resultados demonstram que se formam espumas com más propriedades, especialmente a -10/-10ºC, contudo proporcionou excelentes shaking rate da lata. Através de uma pequena análise de custos não é aconselhável o seu uso pelos resultados obtidos, não proporcionando um balanço custo/benefício favorável. As três melhores espumas obtidas de todos os estudos foram comparadas com uma espuma de inverno presente no mercado. 7396 e 7638 com um volume de 27 % no prépolímero e uma composição de GLP (30/ 0 / 70 w/w%) e (13,7/ 0/ 86,3 w/w%), respectivamente, e 7690, com 37 % de volume no pré-polímero e GLP (30/ 0 / 70 w/w%), apresentaram em geral melhores resultados, comparando com a espuma benchmark . Contudo, os seus shaking rate a -10/-10ºC, de cada espuma, apresentaram valores bastante inferiores à composição benchmarking.

Production of surfactants from bio-materials

Este trabalho foi desenvolvido no âmbito de um projecto europeu, BIOPRODUCTION, tendo em vista o desenvolvimento de dois tipos de biomaterias funcionais: ésteres de açúcares com ácidos gordos (SFAE) e metacrilatos funcionais. A síntese laboratorial do biosurfactante SFAE foi efectuada utilizando como matérias-primas diferentes sacáridos, nomeadamente sacarose, glucose e melaço de cana-de-açúcar (mistura de polissacáridos), e ésteres metílicos de ácidos gordos (FAME) de óleos vegetais, tais como colza e coco. Esta síntese é constituída por dois passos: acilação dos açúcares com anidrido acético, e transesterificação do açúcar acilado com FAME, utilizando triflatos de lantanídeos como catalisador. Diferentes estequiometrias foram testadas, bem como diferentes processos de modo a evitar a degradação dos açúcares. Foram efectuados testes preliminares de emulsão e calculou-se, empiricamente, o respectivo HLB. Procedeu-se à caracterização do produto através de FTIR e RMN e também à optimização iterativa do processo de síntese. A modificação, à escala laboratorial, de metacrilatos de metilo (MMA) realizou-se recorrendo à sua transesterificação com polióis convencionais. Efectuaram-se testes de reticulação do produto com diferentes catalisadores e iniciadores para posterior aplicação em revestimentos de borracha. Por fim, para ambos os produtos serão necessários estudos adicionais de caracterização, nomeadamente tensão superficial para os biosurfactantes e propriedades mecânicas para polímeros modificados com MMA.

CVD of CrO2 thin films: Influence of the deposition parameters on their structural and magnetic properties

This work reports on the synthesis of CrO2 thin films by atmospheric pressure CVD using chromium trioxide (CrO3) and oxygen. Highly oriented (100) CrO2 films containing highly oriented (0001) Cr2O3 were grown onto Al2O3(0001) substrates. Films display a sharp magnetic transition at 375 K and a saturation magnetization of 1.92 mu(B)/f.u., close to the bulk value of 2 mu(B)/f.u. for the CrO2.

KrF pulsed laser deposition of chromium oxide thin films from Cr8O21 targets

Chromium oxides, CrxOy, are of great interest due to the wide variety of their technological applications. Among them, CrO2 has been extensively investigated in recent years because it is an attractive compound for use in spintronic heterostructures. However, its synthesis at low temperatures has been a difficult task due to the metastable nature of this oxide. This is indeed essential to ensure interface quality and the ability to coat thermal-sensitive materials such as those envisaged in spintronic devices. Pulsed Laser Deposition (PLD) is a technique that has the potential to meet the requirements stated above. In this work, we describe our efforts to grow chromium oxide thin films by PLD from Cr8O21 targets, using a KrF excimer laser. The as-deposited films were investigated by X-ray diffraction and Rutherford backscattering spectrometry. Structural and chemical composition studies showed that the films consist of a mixture of amorphous chromium oxides exhibiting different stoichiometries depending on the processing parameters, where nanocrystals of mainly Cr2O3 are dispersed. The analyses do not exclude the possibility of co-deposition of Cr2O3 and a low fraction of CrO2.

Fabrication of Three-Dimensional Dendritic Ni-Co Films By Electrodeposition on Stainless Steel Substrates

Co-deposition of nickel and cobalt was carried out on austenitic stainless steel (AISI 304) substrates by imposing a square waveform current in the cathodic region. The innovative procedure applied in this work allows creating a stable, fully developed, and open porous three-dimensional (3D) dendritic structure, which can be used as electrode for redox supercapacitors. This study investigates in detail the influence of the applied current density on the morphology, mass, and chemical composition of the deposited Ni-Co films and the resulting 3D porous network dendritic structure. The morphology and the physicochemical composition were studied by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and X-ray diffraction (W). The electrochemical behavior of the materials was evaluated by cyclic voltammetry (CV). The results highlight the mechanism involved in the coelectrodeposition process and how the lower limit current density tailors the film composition and morphology, as well as its electrochemical activity.

A new control strategy with saturation effect compensation for an autonomous induction generator drivenby wide speed range turbines

This paper presents a variable speed autonomous squirrel cage generator excited by a current-controlled voltage source inverter to be used in stand-alone micro-hydro power plants. The paper proposes a system control strategy aiming to properly excite the machine as well as to achieve the load voltage control. A feed-forward control sets the appropriate generator flux by taking into account the actual speed and the desired load voltage. A load voltage control loop is used to adjust the generated active power in order to sustain the load voltage at a reference value. The control system is based on a rotor flux oriented vector control technique which takes into account the machine saturation effect. The proposed control strategy and the adopted system models were validated both by numerical simulation and by experimental results obtained from a laboratory prototype. Results covering the prototype start-up, as well as its steady-state and dynamical behavior are presented. (C) 2011 Elsevier Ltd. All rights reserved.