Modular high-current generator for electromagnetic forming with energy recovery

A 10 kJ electromagnetic forming (EMF) modulator with energy recovery based on two resonant power modules, each containing a 4.5 kV/30-kA silicon controlled rectifier, a 1.11-mF capacitor bank and an energy recovery circuit, working in parallel to allow a maximum actuator discharge current amplitude and rate of 50 kA and 2 kA/mu s was successfully developed and tested. It can be plugged in standard single phase 230 V/16 A mains socket and the circuit is able to recover up to 32% of its initial energy, reducing the charging time of conventional EMF systems by up to 68%.

Multilevel high-voltage pulse generation based on a new modular solid-state switch

This paper describes a modular solid-state switching cell derived from the Marx generator concept to be used in topologies for generating multilevel unipolar and bipolar high-voltage (HV) pulses into resistive loads. The switching modular cell comprises two ON/OFF semiconductors, a diode, and a capacitor. This cell can be stacked, being the capacitors charged in series and their voltages balanced in parallel. To balance each capacitor voltage without needing any parameter measurement, a vector decision diode algorithm is used in each cell to drive the two switches. Simulation and experimental results, for generating multilevel unipolar and bipolar HV pulses into resistive loads are presented.

Sistema modular de gestão académica

A concretização do Processo de Bolonha a nível das instituições de ensino superior tornou premente a necessidade de processos de gestão académica envolvendo funcionalidades e formatos de dados heterogéneos. Este trabalho tem por objectivo contribuir para abordar esta necessidade no contexto do ISEL, através da implementação de uma plataforma de integração com características modulares ao nível da camada de negócio do portal académico, no sentido de permitir a integração de subsistemas heterogéneos, quer em termos funcionais, quer em termos de formatos de informação. O projecto Sistema Modular de Gestão Académica (SMGA) foi concretizado através de um protótipo de portal académico que assenta numa arquitectura orientada a serviços, onde é utilizado um modelo de comunicação baseado em mensagens no formato Agent Communication Language (ACL). Este protótipo disponibiliza funcionalidades relacionadas com a gestão académica aos seus utilizadores através de uma aplicação Web de Front Office.

Power Electronics Didactic Modules for Direct Current Machine Control

Several didactic modules for an electric machinery laboratory are presented. The modules are dedicated for DC machinery control and get their characteristic curves. The didactic modules have a front panel with power and signal connectors and can be configurable for any DC motor type. The three-phase bridge inverter proposed is one of the most popular topologies and is commercially available in power package modules. The control techniques and power drives were designed to satisfy static and dynamic performance of DC machines. Each power section is internally self-protected against misconnections and short-circuits. Isolated output signals of current and voltage measurements are also provided, adding versatility for use either in didactic or research applications. The implementation of such modules allowed experimental confirmation of the expected performance.

Grid Integration of Offshore Wind Farms Using Modular Marx Multilevel Converters

This paper proposes the use of a Modular Marx Multilevel Converter, as a solution for energy integration between an offshore Wind Farm and the power grid network. The Marx modular multilevel converter is based on the Marx generator, and solves two typical problems in this type of multilevel topologies: modularity and dc capacitor voltage balancing. This paper details the strategy for dc capacitor voltage equalization. The dynamic models of the converter and power grid are presented in order to design the converter ac output voltages and the dc capacitor voltage controller. The average current control is presented and used for power flow control, harmonics and reactive power compensation. Simulation results are presented in order to show the effectiveness of the proposed (MC)-C-3 topology.

A New Modular Marx Derived Multilevel Converter

A new Modular Marx Multilevel Converter, M(3)C, is presented. The M(3)C topology was developed based on the Marx Generator concept and can contribute to technological innovation for sustainability by enabling wind energy off-shore modular multilevel power switching converters with an arbitrary number of levels. This paper solves both the DC capacitor voltage balancing problem and modularity problems of multilevel converters, using a modified cell of a solid-state Marx modulator, previously developed by authors for high voltage pulsed power applications. The paper details the structure and operation of the M(3)C modules, and their assembling to obtain multilevel converters. Sliding mode control is applied to a M(3)C leg and the vector leading to automatic capacitor voltage equalization is chosen. Simulation results are presented to show the effectiveness of the proposed M(3)C topology.

Projecto, montagem e teste de uma unidade modular de detecção de radiação Geiger-Muller

Dissertação para obtenção do grau de Mestre em Engenharia Electrotécnica Ramo de Automação e Electrónica Industrial

BITalino: a novel hardware framework for physiological computing

Physical computing has spun a true global revolution in the way in which the digital interfaces with the real world. From bicycle jackets with turn signal lights to twitter-controlled christmas trees, the Do-it-Yourself (DiY) hardware movement has been driving endless innovations and stimulating an age of creative engineering. This ongoing (r)evolution has been led by popular electronics platforms such as the Arduino, the Lilypad, or the Raspberry Pi, however, these are not designed taking into account the specific requirements of biosignal acquisition. To date, the physiological computing community has been severely lacking a parallel to that found in the DiY electronics realm, especially in what concerns suitable hardware frameworks. In this paper, we build on previous work developed within our group, focusing on an all-in-one, low-cost, and modular biosignal acquisition hardware platform, that makes it quicker and easier to build biomedical devices. We describe the main design considerations, experimental evaluation and circuit characterization results, together with the results from a usability study performed with volunteers from multiple target user groups, namely health sciences and electrical, biomedical, and computer engineering. Copyright © 2014 SCITEPRESS - Science and Technology Publications. All rights reserved.

Multifunctional controller architecture for sold-state marx modulator based on FPGA

This paper proposes a multifunctional architecture to implement field-programmable gate array (FPGA) controllers for power converters and presents a prototype for a pulsed power generator based on a solid-state Marx topology. The massively parallel nature of reconfigurable hardware platforms provides very high processing power and fast response times allowing the implementation of many subsystems in the same device. The prototype includes the controller, a failure detection system, an interface with a safety/emergency subsystem, a graphical user interface, and a virtual oscilloscope to visualize the generated pulse waveforms, using a single FPGA. The proposed architecture employs a modular design that can be easily adapted to other power converter topologies.

25 kV bipolar solid-state Marx generator for industrial food applications

The preliminary results from a bipolar industrial solidstate based Marx generator, developed for the food industry, capable of delivering 25 kV/250 A positive and negative pulses with 12 kW average power, are presented and discussed. This modular topology uses only four controlled switches per cell, 27 cells in total that can be charged up to 1000V each, the two extra cells are used for droop compensation. The triggering signals for all the switches are generated by a FPGA. Considering that biomaterials are similar to resistive type loads, experimental results from this new bipolar 25 kV modulator into resistive loads are presented and discussed.

High-level Petri nets modules for embedded controllers design

Modular design is crucial to manage large-scale systems and to support the divide-and-conquer development approach. It allows hierarchical representations and, therefore, one can have a system overview, as well as observe component details. Petri nets are suitable to model concurrent systems, but lack on structuring mechanisms to support abstractions and the composition of sub-models, in particular when considering applications to embedded controllers design. In this paper we present a module construct, and an underlying high-level Petri net type, to model embedded controllers. Multiple interfaces can be declared in a module, thus, different instances of the same module can be used in different situations. The interface is a subset of the module nodes, through which the communication with the environment is made. Module places can be annotated with a generic type, overridden with a concrete type at instance level, and constants declared in a module may have a new value in each instance.

Medir e modular

A necessidade de construir que se manifesta em todos os sectores, desde o da habitação, em que o homem recupera da fadiga física e intelectual, consequência da sua actividade diária, até àquele em que exerce a sua actividade de produção ou onde realiza as suas ocupações sociais dos tempos livres, obriga a procurar soluções, para a limitação de espaços - cada vez mais económicos em tempo, dinheiro, materiais e mão de obra. Este objectivo levou ao desenvolvimento de técnicas de pré-fabricação,e bem assim a industrializar a construção, por elementos cada vez maiores - de acordo com os meios mecânicos de que se pode dispor na zona industrial, nos transportes e no estaleiro. Assim, conforme os elementos de construção a colocar em obra são manuseáveis ou, pelas suas dimensões e peso, careçam de meios mecânicos para poderem ser utilizados, a pré fabricação está diferenciada em: a) Pré fabricação ligeira b) Pré fabricação pesada Por outro lado, os diversos materiais que se utilizam na construção permitem a pré fabricação industrial de elementos de construção: metálicos, de madeira, de betão, de pedra, de argila cozida, de vidro, etc.

Integração de informação geográfica

A integração de informação geográfica disponível em diferentes formatos levanta a necessidade de criar mecanismos de resolução de incompatibilidades, tendo em vista facilitar a partilha e reutilização de informação. No âmbito desta dissertação, propõe-se uma arquitectura que efectue a integração de informação geográfica. A arquitectura processa diferentes fontes de informação geográfica com diferentes formatos. A informação geográfica apresentada nas entradas é transformada atendendo a um formato de representação interno e, após ser realizada a sua integração, é disponibilizada em múltiplos formatos de saída. A arquitectura proposta é modular e inclui o módulo de leitura das entradas, o módulo que associa as fontes de informação aos respectivos formatos, o módulo de conversão dos dados de entrada no formato de representação interno e o módulo de integração que gera os dados nos diferentes formatos de saída. Com o objectivo de avaliar experimentalmente a arquitectura, foi desenvolvido um protótipo. Foram processados exemplos de informação geográfica relativos a cenários de integração que cobrem as funcionalidades da arquitectura, nomeadamente a inclusão de novos formatos de informação geográfica e a integração de fontes de informação homogéneas ou heterogéneas. Os resultados obtidos confirmam que a arquitectura proposta é adequada à integração de fontes de informação geográfica e que é uma contribuição válida para a resolução de problemas de interoperabilidade em sistemas de informação geográfica.

Photo-induced instability of nanocrystalline silicon TFTs

We examine the instability behavior of nanocrystalline silicon (nc-Si) thin-film transistors (TFTs) in the presence of electrical and optical stress. The change in threshold voltage and sub-threshold slope is more significant under combined bias-and-light stress when compared to bias stress alone. The threshold voltage shift (Delta V-T) after 6 h of bias stress is about 7 times larger in the case with illumination than in the dark. Under bias stress alone, the primary instability mechanism is charge trapping at the semiconductor/insulator interface. In contrast, under combined bias-and-light stress, the prevailing mechanism appears to be the creation of defect states in the channel, and believed to take place in the amorphous phase, where the increase in the electron density induced by electrical bias enhances the non-radiative recombination of photo-excited electron-hole pairs. The results reported here are consistent with observations of photo-induced efficiency degradation in solar cells.

Using Modern Tools to Explain the Use of the Smith Chart

The concept of explaining the use of an old tool like the Smith chart, using modern tools like MATLAB [1] scripts in combination with e-learning facilities, is exemplified by two MATLAB scripts. These display, step by step, the graphical procedure that must be used to solve the double-stub impedance-matching problem. These two scripts correspond to two different possible ways to analyze this matching problem, and they are important for students to learn by themselves.