Synthesis and characterization of COPPER(II) 4´-phenyl-terpyridine compounds and catalytic application for aerobic oxidation of benzylic alcohols

The reactions between 4'-phenyl-terpyridine (L) and nitrate, acetate or chloride Cu(II) salts led to the formation of [Cu(NO3)(2)L] (1), [Cu(OCOCH3)(2)L]center dot CH2Cl2 (2 center dot CH2Cl2)and [CuCl2L]center dot[Cu(Cl)(mu-Cl)L](2) (3), respectively. Upon dissolving 1 in mixtures of DMSO-MeOH or EtOH-DMF the compounds [Cu(H2O){OS(CH3)(2)}L]-(NO3)(2) (4) and [Cu(HO)(CH3CH2OH)L](NO3) (5) were obtained, in this order. Reaction of 3 with AgSO3CF3 led to [CuCl(OSO2CF3)L] (6). The compounds were characterized by ESI-MS, IR, elemental analysis, electrochemical techniques and, for 2-6, also by single crystal X-ray diffraction. They undergo, by cyclic voltammetry, two single-electron irreversible reductions assigned to Cu(II) -> Cu(I)and Cu(I) -> Cu(0) and, for those of the same structural type, the reduction potential appears to correlate with the summation of the values of the Lever electrochemical EL ligand parameter, which is reported for the first time for copper complexes. Complexes 1-6 in combination with TEMPO (2,2,6,6-tetramethylpiperidinyl-1-oxyl radical) can exhibit a high catalytic activity, under mild conditions and in alkaline aqueous solution, for the aerobic oxidation of benzylic alcohols. Molar yields up to 94% (based on the alcohol) with TON values up to 320 were achieved after 22 h.

InOx thin films deposited by plasma assisted evaporation: application in light shutters

An integration of undoped InOx and commercial ITO thin films into laboratory assembled light shutter devices is made. Accordingly, undoped transparent conductive InOx thin films, about 100 nm thick, are deposited by radiofrequency plasma enhanced reactive thermal evaporation (rf-PERTE) of indium teardrops with no intentional heating of the glass substrates. The process of deposition occurs at very low deposition rates (0.1-0.3 nm/s) to establish an optimized reaction between the oxygen plasma and the metal vapor. These films show the following main characteristics: transparency of 87% (wavelength, lambda = 632.8 nm) and sheet resistance of 52 Omega/sq; while on commercial ITO films the transparency was of 92% and sheet resistance of 83 Omega/sq. The InOx thin film surface characterized by AFM shows a uniform grain texture with a root mean square surface roughness of Rq similar to 2.276 nm. In contrast, commercial ITO topography is characterized by two regions: one smoother with Rq similar to 0.973 nm and one with big grains (Rq similar to 3.617 nm). For the shutters assembled using commercial ITO, the light transmission coefficient (Tr) reaches the highest value (Tr-max) of 89% and the lowest (Tr-min) of 1.3% [13], while for the InOx shutters these values are 80.1% and 3.2%, respectively. Regarding the electric field required to achieve 90% of the maximum transmission in the ON state (E-on), the one presented by the devices assembled with commercial ITO coated glasses is 2.41 V/mu m while the one presented by the devices assembled with InOx coated glasses is smaller, 1.77 V/mu m. These results corroborate the device quality that depends on the base materials and fabrication process used. (C) 2014 Elsevier Ltd. All rights reserved.

Application of neural networks for pavement evaluation

As vias de comunicação são indispensáveis para o desenvolvimento de uma nação, económica e socialmente. Num mundo globalizado, onde tudo deve chegar ao seu destino no menor espaço de tempo, as vias de comunicação assumem um papel vital. Assim, torna-se essencial construir e manter uma rede de transportes eficiente. Apesar de não ser o método mais eficiente, o transporte rodoviário é muitas vezes o mais económico e possibilita o transporte porta-a-porta, sendo em muitos casos o único meio de transporte possível. Por estas razões, o modo rodoviário tem uma quota significativa no mercado dos transportes, seja de passageiros ou mercadorias, tornando-o extremamente importante na rede de transportes de um país. Os países europeus fizeram um grande investimento na criação de extensas redes de estradas, cobrindo quase todo o seu território. Neste momento, começa-se a atingir o ponto onde a principal preocu+ação das entidades gestoras de estradas deixa de ser a construção de novas vias, passando a focar-se na necessidade de manutenção e conservação das vias existentes. Os pavimentos rodoviários, como todas as outras construções, requerem manutenção de forma a garantir bons níveis de serviço com qualidade, conforto e segurança. Devido aos custos inerentes às operações de manutenção de pavimentos, estas devem rigorosamente e com base em critérios científicos bem definidos. Assim, pretende-se evitar intervenções desnecessárias, mas também impedir que os danos se tornem irreparáveis e economicamente prejudiciais, com repercussões na segurança dos utilizadores. Para se estimar a vida útil de um pavimento é essencial realizar primeiro a caracterização estrutural do mesmo. Para isso, torna-se necessário conhecer o tipo de estrutura de um pavimento, nomeadamente a espessura e o módulo de elasticidade constituintes. A utilização de métodos de ensaio não destrutivos é cada vez mais reconhecida como uma forma eficaz para obter informações sobre o comportamento estrutural de pavimentos. Para efectuar estes ensaios, existem vários equipamentos. No entanto, dois deles, o Deflectómetro de Impacto e o Radar de Prospecção, têm demonstrado ser particularmente eficientes para avaliação da capacidade de carga de um pavimento, sendo estes equipamentos utilizados no âmbito deste estudo. Assim, para realização de ensaios de carga em pavimentos, o equipamento Deflectómetro de Impacto tem sido utilizado com sucesso para medir as deflexões à superfície de um pavimento em pontos pré-determinados quando sujeito a uma carga normalizada de forma a simular o efeito da passagem da roda de um camião. Complementarmente, para a obtenção de informações contínuas sobre a estrutura de um pavimento, o equipamento Radar de Prospecção permite conhecer o número de camadas e as suas espessuras através da utilização de ondas electromagnéticas. Os dados proporcionam, quando usados em conjunto com a realização de sondagens à rotação e poços em alguns locais, permitem uma caracterização mais precisa da condição estrutural de um pavimento e o estabelecimento de modelos de resposta, no caso de pavimentos existentes. Por outro lado, o processamento dos dados obtidos durante os ensaios “in situ” revela-se uma tarefa morosa e complexa. Actualmente, utilizando as espessuras das camadas do pavimento, os módulos de elasticidade das camadas são calculados através da “retro-análise” da bacia de deflexões medida nos ensaios de carga. Este método é iterativo, sendo que um engenheiro experiente testa várias estruturas diferentes de pavimento, até se obter uma estrutura cuja resposta seja o mais próximo possível da obtida durante os ensaios “in Situ”. Esta tarefa revela-se muito dependente da experiência do engenheiro, uma vez que as estruturas de pavimento a serem testadas maioritariamente do seu raciocínio. Outra desvantagem deste método é o facto de apresentar soluções múltiplas, dado que diferentes estruturas podem apresentar modelos de resposta iguais. A solução aceite é, muitas vezes, a que se julga mais provável, baseando-se novamente no raciocínio e experiência do engenheiro. A solução para o problema da enorme quantidade de dados a processar e das múltiplas soluções possíveis poderá ser a utilização de Redes Neuronais Artificiais (RNA) para auxiliar esta tarefa. As redes neuronais são elementos computacionais virtuais, cujo funcionamento é inspirado na forma como os sistemas nervosos biológicos, como o cérebro, processam a informação. Estes elementos são compostos por uma série de camadas, que por sua vez são compostas por neurónios. Durante a transmissão da informação entre neurónios, esta é modificada pela aplicação de um coeficiente, denominado “peso”. As redes neuronais apresentam uma habilidade muito útil, uma vez que são capazes de mapear uma função sem conhecer a sua fórmula matemática. Esta habilidade é utilizada em vários campos científicos como o reconhecimento de padrões, classificação ou compactação de dados. De forma a possibilitar o uso desta característica, a rede deverá ser devidamente “treinada” antes, processo realizado através da introdução de dois conjuntos de dados: os valores de entrada e os valores de saída pretendidos. Através de um processo cíclico de propagação da informação através das ligações entre neurónios, as redes ajustam-se gradualmente, apresentando melhores resultados. Apesar de existirem vários tipos de redes, as que aparentam ser as mais aptas para esta tarefa são as redes de retro-propagação. Estas possuem uma característica importante, nomeadamente o treino denominado “treino supervisionado”. Devido a este método de treino, as redes funcionam dentro da gama de variação dos dados fornecidos para o “treino” e, consequentemente, os resultados calculados também se encontram dentro da mesma gama, impedindo o aparecimento de soluções matemáticas com impossibilidade prática. De forma a tornar esta tarefa ainda mais simples, foi desenvolvido um programa de computador, NNPav, utilizando as RNA como parte integrante do seu processo de cálculo. O objectivo é tornar o processo de “retro-análise” totalmente automático e prevenir erros induzidos pela falta de experiência do utilizador. De forma a expandir ainda mais as funcionalidades do programa, foi implementado um processo de cálculo que realiza uma estimativa da capacidade de carga e da vida útil restante do pavimento, recorrendo a dois critérios de ruína. Estes critérios são normalmente utilizados no dimensionamento de pavimentos, de forma a prevenir o fendilhamento por fadiga e as deformações permanentes. Desta forma, o programa criado permite a estimativa da vida útil restante de um pavimento de forma eficiente, directamente a partir das deflexões e espessuras das camadas, medidas nos ensaios “in situ”. Todos os passos da caracterização estrutural do pavimento são efectuados pelo NNPav, seja recorrendo à utilização de redes neuronais ou a processos de cálculo matemático, incluindo a correcção do módulo de elasticidade da camada de misturas betuminosas para a temperatura de projecto e considerando as características de tráfego e taxas de crescimento do mesmo. Os testes efectuados às redes neuronais revelaram que foram alcançados resultados satisfatórios. Os níveis de erros na utilização de redes neuronais são semelhantes aos obtidos usando modelos de camadas linear-elásticas, excepto para o cálculo da vida útil com base num dos critérios, onde os erros obtidos foram mais altos. No entanto, este processo revela-se bastante mais rápido e possibilita o processamento dos dados por pessoal com menos experiência. Ao mesmo tempo, foi assegurado que nos ficheiros de resultados é possível analisar todos os dados calculados pelo programa, em várias fases de processamento de forma a permitir a análise detalhada dos mesmos. A possibilidade de estimar a capacidade de carga e a vida útil restante de um pavimento, contempladas no programa desenvolvido, representam também ferramentas importantes. Basicamente, o NNPav permite uma análise estrutural completa de um pavimento, estimando a sua vida útil com base nos ensaios de campo realizados pelo Deflectómetro de Impacto e pelo Radar de Prospecção, num único passo. Complementarmente, foi ainda desenvolvido e implementado no NNPav um módulo destinado ao dimensionamento de pavimentos novos. Este módulo permite que, dado um conjunto de estruturas de pavimento possíveis, seja estimada a capacidade de carga e a vida útil daquele pavimento. Este facto permite a análise de uma grande quantidade de estruturas de pavimento, e a fácil comparação dos resultados no ficheiro exportado. Apesar dos resultados obtidos neste trabalho serem bastante satisfatórios, os desenvolvimentos futuros na aplicação de Redes Neuronais na avaliação de pavimentos são ainda mais promissores. Uma vez que este trabalho foi limitado a uma moldura temporal inerente a um trabalho académico, a possibilidade de melhorar ainda mais a resposta das RNA fica em aberto. Apesar dos vários testes realizados às redes, de forma a obter as arquitecturas que apresentassem melhores resultados, as arquitecturas possíveis são virtualmente ilimitadas e pode ser uma área a aprofundar. As funcionalidades implementadas no programa foram as possíveis, dentro da moldura temporal referida, mas existem muitas funcionalidades a serem adicinadas ou expandidas, aumentando a funcionalidade do programa e a sua produtividade. Uma vez que esta é uma ferramenta que pode ser aplicada ao nível de gestão de redes rodoviárias, seria necessário estudar e desenvolver redes similares de forma a avaliar outros tipos de estruturas de pavimentos. Como conclusão final, apesar dos vários aspectos que podem, e devem ser melhorados, o programa desenvolvido provou ser uma ferramenta bastante útil e eficiente na avaliação estrutural de pavimentos com base em métodos de ensaio não destrutivos.

Application of GIS-based multi-criteria analysis for site selection of aquifer recharge with reclaimed water

Reclaimed water from small wastewater treatment facilities in the rural areas of the Beira Interior region (Portugal) may constitute an alternative water source for aquifer recharge. A 21-month monitoring period in a constructed wetland treatment system has shown that 21,500 m(3) year(-1) of treated wastewater (reclaimed water) could be used for aquifer recharge. A GIS-based multi-criteria analysis was performed, combining ten thematic maps and economic, environmental and technical criteria, in order to produce a suitability map for the location of sites for reclaimed water infiltration. The areas chosen for aquifer recharge with infiltration basins are mainly composed of anthrosol with more than 1 m deep and fine sand texture, which allows an average infiltration velocity of up to 1 m d(-1). These characteristics will provide a final polishing treatment of the reclaimed water after infiltration (soil aquifer treatment (SAT)), suitable for the removal of the residual load (trace organics, nutrients, heavy metals and pathogens). The risk of groundwater contamination is low since the water table in the anthrosol areas ranges from 10 m to 50 m. Oil the other hand, these depths allow a guaranteed unsaturated area suitable for SAT. An area of 13,944 ha was selected for study, but only 1607 ha are suitable for reclaimed water infiltration. Approximately 1280 m(2) were considered enough to set up 4 infiltration basins to work in flooding and drying cycles.

A 3-phase model for VIS/NIR mu C-Si : H p-i-n detectors

The spectral response and the photocurrent delivered by entirely microcrystalline p-i-n-Si:H detectors an analysed under different applied bias and light illumination conditions. The spectral response and the internal collection depend not only on the energy range but also on the illumination side. Under [p]- and [n]-side irradiation, the internal collection characteristics have an atypical shape. It is high for applied bias and lower than the open circuit voltage, shows a steep decrease near the open circuit voltage (higher under [n]-side illumination) and levels off for higher voltages. Additionally, the numerical modeling of the VIS/NIR detector, based on the band discontinuities near the grain boundaries and interfaces, complements the study and gives insight into the internal physical process.

The US actuarial balance model for the pay-as-you-go system and its application to Spain

The aim of this paper is to formulate an approximation of the US actuarial balance model and apply it to the Spanish public retirement pension system under various scenarios in order to determine a consistent indicator of the system's financial state comparable to those used by the most advanced social security systems. This will enable us to answer the question as to whether there is any justification for reforming the pension system in Spain. This type of actuarial balance uses projections to show future challenges to the financial side of the pension system deriving basically from ageing, the projected increase in longevity and fluctuations in economic activity. If one is compiled periodically it can provide various indicators to help depoliticize the management of the pay-as-you-go system by bringing the planning horizons of politicians and the system itself closer together.

Genotoxicity biomarkers: application in histopathology laboratories

Most cancers results from man-made and natural environmental exposures (such as tobacco smoke; chemical pollutants in air, water, food, drugs; radon; and infectious agents) acting in concert with both genetic and acquired characteristics. It has been estimated that without these environmental factors, cancer incidence would be dramatically reduced, by as much as 80%-90%. The modulation of environmental factors by host susceptibility was rarely evaluated. However, within the past few years, the interaction between environmental factors and host susceptibility factors has become a very active area of research. Molecular biology as a tool for use in epidemiological studies has significant potential in strengthening the identification of cancers associated with environmental exposures related to lifestyle, occupation, or ambient pollution. In molecular epidemiology, laboratory methods are employed to document the molecular basis and preclinical effects of environmental carcinogenesis. Molecular epidemiology has become a major field of research and considerable progress has been made in validation and application of biomarkers and its greatest contribution has been the insights provided into interindividual variation in human cancer risk and the complex interactions between environmental factors and host susceptibility factors, both inherited and acquired, in the multistage process of carcinogenesis.

A DC-DC Step-Up mu-Power Converter for Energy Harvesting Applications, Using Maximum Power PointTracking, Based on Fractional Open Circuit Voltage

A DC-DC step-up micro power converter for solar energy harvesting applications is presented. The circuit is based on a switched-capacitorvoltage tripler architecture with MOSFET capacitors, which results in an, area approximately eight times smaller than using MiM capacitors for the 0.131mu m CMOS technology. In order to compensate for the loss of efficiency, due to the larger parasitic capacitances, a charge reutilization scheme is employed. The circuit is self-clocked, using a phase controller designed specifically to work with an amorphous silicon solar cell, in order to obtain themaximum available power from the cell. This will be done by tracking its maximum power point (MPPT) using the fractional open circuit voltage method. Electrical simulations of the circuit, together with an equivalent electrical model of an amorphous silicon solar cell, show that the circuit can deliver apower of 1132 mu W to the load, corresponding to a maximum efficiency of 66.81%.

A Step-up mu-Power Converter for Solar Energy Harvesting Applications, using Hill Climbing Maximum Power Point Tracking

This paper presents a step-up micro-power converter for solar energy harvesting applications. The circuit uses a SC voltage tripler architecture, controlled by an MPPT circuit based on the Hill Climbing algorithm. This circuit was designed in a 0.13 mu m CMOS technology in order to work with an a-Si PV cell. The circuit has a local power supply voltage, created using a scaled down SC voltage tripler, controlled by the same MPPT circuit, to make the circuit robust to load and illumination variations. The SC circuits use a combination of PMOS and NMOS transistors to reduce the occupied area. A charge re-use scheme is used to compensate the large parasitic capacitors associated to the MOS transistors. The simulation results show that the circuit can deliver a power of 1266 mu W to the load using 1712 mu W of power from the PV cell, corresponding to an efficiency as high as 73.91%. The simulations also show that the circuit is capable of starting up with only 19% of the maximum illumination level.

Application of adaptive neuro-fuzzy inference for wind power short-term forecasting

The increased integration of wind power into the electric grid, as nowadays occurs in Portugal, poses new challenges due to its intermittency and volatility. Hence, good forecasting tools play a key role in tackling these challenges. In this paper, an adaptive neuro-fuzzy inference approach is proposed for short-term wind power forecasting. Results from a real-world case study are presented. A thorough comparison is carried out, taking into account the results obtained with other approaches. Numerical results are presented and conclusions are duly drawn. (C) 2011 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.

Copper Bis(oxazoline) Encapsulated in Zeolites and Its Application as Heterogeneous Catalysts for the Cyclopropanation of Styrene

A copper C(2)-symmetric bis(oxazoline), CuBox, was introduced in two forms of commercial Y zeolite: a sodium form (NaY) and an ultrastable form (NaUSY). CuBox was introduced by first partially exchanging the sodium cations of both zeolites for copper and then by refluxing the obtained materials with a solution of bis(oxazoline) (Box). Two different loadings were prepared for each form of zeolite. The materials were characterized by copper ICP-AES, elemental analysis, XPS, FTIR, TG, and nitrogen adsorption isotherms at -196 degrees C. Evidence for Box ligand location in the supercages of NaY and NaUSY zeolites and its coordination to the exchanged copper(II) was obtained by the several techniques used. The materials were all active in the cyclopropanation of styrene with ethyldiazoacetate at room temperature and diastereoselective toward trans cydopropanes. Although the materials containing Box showed low enantioselectivities, their catalytic activities were higher than the parent copper exchanged zeolites, and did not decrease with reuse, at least during three consecutive cycles.

Size distribution of polycyclic aromatic hydrocarbons in a roadway tunnel in Lisbon, Portugal

Atmospheric aerosols of four aerodynamic size ranges were collected using high volume cascade impactors in an extremely busy roadway tunnel in Lisbon (Portugal). Dust deposited on the tunnel walls and guardrails was also collected. Average particle mass concentrations in the tunnel atmosphere were more than 30 times higher than in the outside urban background air, revealing its origins almost exclusively from fresh vehicle emissions. Most of the aerosol mass was concentrated in submicrometer fractions (65%), and polycyclic aromatic hydrocarbons (PAH) were even more concentrated in the finer particles with an average of 84% of total PAH present in sizes smaller than 0.49 mu m. The most abundant PAH were methylated phenanthrenes, fluoranthene and pyrene. About 46% of the total PAH mass was attributed to lower molecular weight compounds (two and three rings), suggesting a strong influence of diesel vehicle emissions on the production of local particulate PAH. The application of diagnostic ratios confirmed the relevance of this source of PAH in the tunnel ambient air. Deposited dust presented PAH profiles similar to the coarser aerosol size range, in agreement with the predominant origin of coarser aerosol particles from soil dust resuspension and vehicle wear products. (c) 201 1 Elsevier Ltd. All rights reserved.

Synthesis and structural characterization of iron complexes with 2,2,2-tris(1-pyrazolyl)ethanol ligands: Application in the peroxidative oxidation of cyclohexane under mild conditions

The reactions of FeCl2 center dot 2H(2)O and 2,2,2-tris(1-pyrazolyl) ethanol HOCH2C(pz)(3) (1) (pz = pyrazolyl) afford [Fe{HOCH2C(pz)(3)}(2)][FeCl4]Cl (2), [Fe{HOCH2C(pz)(3)}(2)](2)[Fe2OCl6](Cl)(2)center dot 4H(2)O (3 center dot 4H(2)O), [Fe{HOCH2C(pz)(3)}(2)] [FeCl{HOCH2C(pz)(3)}(H2O)(2)](2)(Cl)(4) (4) or [Fe{HOCH2C(pz)(3)}(2)]Cl-2 (5), depending on the experimental conditions. Compounds 1-5 were isolated as air-stable crystalline solids and fully characterized, including (1-4) by single-crystal X-ray diffraction analyses. The latter technique revealed strong intermolecular H-bonds involving the OH group of the scorpionate 2 and 3 giving rise to 1D chains which, in 3, are further expanded to a 2D network with intercalated infinite and almost plane chains of H-interacting water molecules. In 4, intermolecular pi center dot center dot center dot pi interactions involving the pyrazolyl rings are relevant. Complexes 2-5 display a high solubility in water (S-25 degrees C ca. 10-12 mg mL(-1)), a favourable feature towards their application as catalysts (or catalyst precursors) for the peroxidative oxidation of cyclo-hexane to cyclohexanol and cyclohexanone, with aqueous H2O2/MeCN, at room temperature (TON values up to ca. 385). (C) 2011 Elsevier B. V. All rights reserved.

Two-way MANCOVA: an application to public health

The aim of this work is to use the MANCOVA model to study the influence of the phenotype of an enzyme - Acid phosphatase - and a genetic factor - Haptoglobin genotype - on two dependent variables - Activity of Acid Phosphatase (ACP1) and the Body Mass Index (BMI). Therefore it's used a general linear model, namely a multivariate analysis of covariance (Two-way MANCOVA). The covariate is the age of the subject. This covariate works as control variable for the independent factors, serving to reduce the error term in the model. The main results showed that only the ACP1 phenotype has a significant effect on the activity of ACP1 and the covariate has a significant effect in both dependent variables. The univariate analysis showed that ACP1 phenotype accounts for about 12.5% of the variability in the activity of ACP1. In respect to this covariate it can be seen that accounts for about 4.6% of the variability in the activity of ACP1 and 37.3% in the BMI.

The electric vehicle integration into the power system: an application to the portuguese case

Electric vehicles (EV) offer a great potential to address the integration of renewable energy sources (RES) in the power grid, and thus reduce the dependence on oil as well as the greenhouse gases (GHG) emissions. The high share of wind energy in the Portuguese energy mix expected for 2020 can led to eventual curtailment, especially during the winter when high levels of hydro generation occur. In this paper a methodology based on a unit commitment and economic dispatch is implemented, and a hydro-thermal dispatch is performed in order to evaluate the impact of the EVs integration into the grid. Results show that the considered 10 % penetration of EVs in the Portuguese fleet would increase load in 3 % and would not integrate a significant amount of wind energy because curtailment is already reduced in the absence of EVs. According to the results, the EV is charged mostly with thermal generation and the associated emissions are much higher than if they were calculated based on the generation mix.