3 resultados para FIBROUS SHEATH
em Repositório Científico do Instituto Politécnico de Lisboa - Portugal
Resumo:
O presente relatório visa apresentar o trabalho desenvolvido pelo estagiário na empresa Freyssinet – Terra Armada, S.A. (FTA). O relatório traduz o acompanhamento do estagiário na construção e aplicação da tecnologia Terra Armada em duas passagens inferiores, bem como o acompanhamento dos trabalhos efectuados pela empresa FTA no que diz respeito à aplicação da tecnologia Freyssinet na ponte sobre o rio Antuã, estando ambas as obras abordadas inseridas no Lote 8 – “A32/IC2 Oliveira de Azeméis/IP1 (S. Lourenço) trecho 2 e 3 – a cargo da empresa Alves Ribeiro S.A.. Com a construção dos trechos 2 e 3 da A32 surgiu a necessidade de se restabelecerem algumas ligações, o que fez com que após estudadas as soluções passíveis de serem utilizadas, se tivesse optado pela construção de túneis a céu aberto na execução dos restabelecimentos. Descreve-se neste documento a metodologia utilizada e as tecnologias patenteadas pela empresa Terra Armada, sendo estas compostas pelos Arcos “Techspan” e muros de ala executados com recurso à tecnologia “Terra Armada”. Em relação à ponte sobre o rio Antuã inserida no trecho 2 da empreitada de construção da A32, foi construída com recurso a cimbre auto-lançável e betonada in situ, havendo a necessidade de aplicação de tecnologias patenteadas pela Freyssinet no que diz respeito às actividades de pré-esforço, aparelhos de apoio nas ligações entre o tabuleiro e os pilares e juntas de dilatação na ligação do tabuleiro aos encontros. Apresentam-se os procedimentos de montagem e aplicação das tecnologias anteriormente referidas. No presente relatório estão descritos e explicados detalhadamente os trabalhos executados pela FTA, nomeadamente a aplicação da tecnologia “Terra Armada” no que diz respeito à construção das passagens inferiores, e a aplicação da tecnologia “Freyssinet” aplicada aquando da construção da ponte sobre o rio Antuã.
Resumo:
This paper deals with the coupled effect of temperature and silica fume addition on rheological, mechanical behaviour and porosity of grouts based on CEMI 42.5R, proportioned with a polycarboxylate-based high range water reducer. Preliminary tests were conducted to focus on the grout best able to fill a fibrous network since the goal of this study was to develop an optimized grout able to be injected in a mat of steel fibers for concrete strengthening. The grout composition was developed based on criteria for fresh state and hardened state properties. For a CEMI 42.5R based grout different high range water reducer dosages (0%, 0.2%, 0.4%, 0.5%, 0.7%) and silica fume (SF) dosages (0%, 2%, 4%) were tested (as replacement of cement by mass). Rheological measurements were used to investigate the effect of polycarboxylates (PCEs) and SF dosage on grout properties, particularly its workability loss, as the mix was to be injected in a matrix of steel fibers for concrete jacketing. The workability behaviour was characterized by the rheological parameters yield stress and plastic viscosity (for different grout temperatures and resting times), as well as the procedures of mini slump cone and funnel flow time. Then, further development focused only on the best grout compositions. The cement substitution by 2% of SF exhibited the best overall behaviour and was considered as the most promising compared to the others compositions tested. Concerning the fresh state analysis, a significant workability loss was detected if grout temperature increased above 35 degrees C. Below this temperature the grout presented a self-levelling behaviour and a life time equal to 45 min. In the hardened state, silica fumes increased not only the grout's porosity but also the grout's compressive strength at later ages, since the pozzolanic contribution to the compressive strength does not occur until 28 d and beyond. (C) 2012 Elsevier Ltd. All rights reserved.
Resumo:
The erosion depth profile of planar targets in balanced and unbalanced magnetron cathodes with cylindrical symmetry is measured along the target radius. The magnetic fields have rotational symmetry. The horizontal and vertical components of the magnetic field B are measured at points above the cathode target with z = 2 x 10(-3) m. The experimental data reveal that the target erosion depth profile is a function of the angle. made by B with a horizontal line defined by z = 2 x 10(-3) m. To explain this dependence a simplified model of the discharge is developed. In the scope of the model, the pathway lengths of the secondary electrons in the pre-sheath region are calculated by analytical integration of the Lorentz differential equations. Weighting these lengths by using the distribution law of the mean free path of the secondary electrons, we estimate the densities of the ionizing events over the cathode and the relative flux of the sputtered atoms. The expression so deduced correlates for the first time the erosion depth profile of the target with the angle theta. The model shows reasonably good fittings to the experimental target erosion depth profiles confirming that ionization occurs mainly in the pre-sheath zone.