Ash deposition during the co-firing of bituminous coal with pine sawdust and olive stones in a laboratory furnace

This article describes an experimental study on ash deposition during the co-firing of bituminous coal with pine sawdust and olive stones in a laboratory furnace. The main objective of this study was to relate the ash deposit rates with the type of biomass burned and its thermal percentage in the blend. The thermal percentage of biomass in the blend was varied between 10% and 50% for both sawdust and olive stones. For comparison purposes, tests have also been performed using only coal or only biomass. During the tests, deposits were collected with the aid of an air-cooled deposition probe placed far from the flame region, where the mean gas temperature was around 640 degrees C. A number of deposit samples were subsequently analyzed on a scanning electron microscope equipped with an energy dispersive X-ray detector. Results indicate that blending sawdust with coal decreases the deposition rate as compared with the firing of unblended coal due to both the sawdust low ash content and its low alkalis content. The co-firing of coal and sawdust yields deposits with high levels of silicon and aluminium which indicates the presence of ashes with high fusion temperature and, thus, with less capacity to adhere to the surfaces. In contrast, in the co-firing of coal with olive stones the deposition rate increases as compared with the firing of unblended coal and the deposits produced present high levels of potassium, which tend to increase their stickiness.

Simulação interactiva do mercado de energia eléctrica

A área de comercialização de energia eléctrica conheceu uma profunda mudança após a liberalização do sector eléctrico, que levou à criação de algumas entidades, as quais gerem os mercados de electricidade europeus. Relativamente a Portugal e Espanha, durante esse processo de liberalização, deu-se também um acordo que os levou à criação de um mercado conjunto, um mercado Ibérico (MIBEL). Dentro deste mercado estão contemplados dois operadores, sendo que um deles representa o pólo Português (OMIP) e o outro representa o pólo Espanhol (OMEL). O OMIP contempla os mercados a prazo, ou futuros, normalmente apresenta contratos de energia comercializada com durabilidade de semanas, meses, trimestres, semestres ou mesmo anos. Diariamente estes contratos poderão vencer no OMEL, que engloba os mercados, diário e intradiário. Este, ao contrário do OMIP negoceia para o dia seguinte (mercado diário) ou para uma determinada altura do dia (mercado intra diário). O mercado diário será o exemplo usado para a criação do simulador interactivo do mercado de energia eléctrica. Este será composto por diversos utilizadores (jogadores), que através de uma plataforma HTML irão investir em centrais de energia eléctrica, negociar licitações e analisar o funcionamento e resultados deste mercado. Este jogo subdividir-se-á então em 3 fases: 1. Fase de investimento; 2. Fase de venda (licitações); 3. Fase de mercado. Na fase do investimento, o jogador terá a possibilidade de adquirir unidades de geração de energia eléctrica de seis tipos de tecnologia: 1. Central a Carvão; 2. Central de Ciclo Combinado; 3. Central Hídrica; 4. Central Eólica; 5. Central Solar; 6. Central Nuclear. Com o decorrer das jogadas o jogador poderá aumentar a sua capacidade de investimento, com a venda de energia, sendo o vencedor aquele que mais saldo tiver no fim do número de jogadas previamente definidos, ou aquele que mais depressa atingir o saldo definido como limite pelo administrador do jogo. A nível pedagógico este simulador é muito interessante pois para além de o utilizador ficar a conhecer as tecnologias em causa e as vantagens e desvantagens das centrais de energia renovável e das centrais a combustíveis fósseis, este ganha igualmente uma sensibilidade para questões de nível ambiental, tais como o aumento dos gases de estufa e o degelo resultante do aquecimento global provocado por esses gases. Para além do conhecimento adquirido na parte de energia eléctrica este jogo dará a conhecer ao utilizador o funcionamento do mercado da energia eléctrica, bem como as tácticas que este poderá usar a seu favor neste tipo de mercado.

New Steel Alloys for the Design of Heat Recovery Steam Generator Components of Combined Cycle Gas Plants

Demand for power is growing every day, mainly due to emerging economies in countries such as China, Russia, India, and Brazil. During the last 50 years steam pressure and temperature in power plants have been continuously raised to improve thermal efficiency. Recent efforts to improve efficiency leads to the development of a new generation of heat recovery steam generator, where the Benson once-through technology is applied to improve the thermal efficiency. The main purpose of this paper is to analyze the mechanical behavior of a high pressure superheater manifold by applying finite element modeling and a finite element analysis with the objective of analyzing stress propagation, leading to the study of damage mechanism, e.g., uniaxial fatigue, uniaxial creep for life prediction. The objective of this paper is also to analyze the mechanical properties of the new high temperature resistant materials in the market such as 2Cr Bainitic steels (T/P23 and T/P24) and also the 9-12Cr Martensitic steels (T/P91, T/P92, E911, and P/T122). For this study the design rules for construction of power boilers to define the geometry of the HPSH manifold were applied.

Characterization of airborne particles generated from metal active gas welding process

This study is focused on the characterization of particles emitted in the metal active gas welding of carbon steel using mixture of Ar + CO2, and intends to analyze which are the main process parameters that influence the emission itself. It was found that the amount of emitted particles (measured by particle number and alveolar deposited surface area) are clearly dependent on the distance to the welding front and also on the main welding parameters, namely the current intensity and heat input in the welding process. The emission of airborne fine particles seems to increase with the current intensity as fume-formation rate does. When comparing the tested gas mixtures, higher emissions are observed for more oxidant mixtures, that is, mixtures with higher CO2 content, which result in higher arc stability. These mixtures originate higher concentrations of fine particles (as measured by number of particles by cm 3 of air) and higher values of alveolar deposited surface area of particles, thus resulting in a more severe worker's exposure.

The effect of metal transfer modes and shielding gas composition on the emission of ultraafine particles in MAG steel welding

The present study aims to characterize ultrafine particles emitted during gas metal arc welding of mild steel and stainless steel, using different shielding gas mixtures, and to evaluate the effect of metal transfer modes, controlled by both processing parameters and shielding gas composition, on the quantity and morphology of the ultrafine particles. It was found that the amount of emitted ultrafine particles (measured by particle number and alveolar deposited surface area) are clearly dependent from the main welding parameters, namely the current intensity and the heat input of the Welding process. The emission of airborne ultrafine particles increases with the current intensity as fume formation rate does. When comparing the shielding gas mixtures, higher emissions were observed for more oxidizing mixtures, that is, with higher CO2 content, which means that these mixtures originate higher concentrations of ultrafine particles (as measured by number of particles. by cubic centimeter of air) and higher values of alveolar deposited surface area of particles, thus resulting in a more hazardous condition regarding welders exposure.

Análise do efeito de implementação de armazenamento térmico em banco de gelo e armazenamento elétrico em baterias Sódio-Enxofre (NaS) sobre o custo de exploração de edifícios de serviços

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica

Preliminary study of synthesis gas production from water electrolysis, using the ELECTROFUEL (R) concept

This paper describes preliminary work on the generation of synthesis gas from water electrolysis using graphite electrodes without the separation of the generated gases. This is an innovative process, that has no similar work been done earlier. Preliminary tests allowed to establish correlations between the applied current to the electrolyser and flow rate and composition of the generated syngas, as well as a characterisation of generated carbon nanoparticles. The obtained syngas can further be used to produce synthetic liquid fuels, for example, methane, methanol or DME (dimethyl ether) in a catalytic reactor, in further stages of a present ongoing project, using the ELECTROFUEL® concept. The main competitive advantage of this project lies in the built-in of an innovative technology product, from RE (renewable energy) power in remote locations, for example, islands, villages in mountains as an alternative for energy storage for mobility constraints.