Thermomechanical environment characterisation in injection moulding and its relation to the mechanical properties of talc-filled polypropylene

This study is focused on the establishment of relationships between the injection moulding processing conditions, the applied thermomechanical environment (TME) and the tensile properties of talc-filled polypropylene,adopting a new extended concept of thermomechanical indices (TMI). In this approach, TMI are calculated from computational simulations of the moulding process that characterise the TME during processing, which are then related to the mechanical properties of the mouldings. In this study, this concept is extended to both the filling and the packing phases, with new TMI defined related to the morphology developed during these phases. A design of experiments approach based on Taguchi orthogonal arrays was adopted to vary the injection moulding parameters (injection flow rate, injection temperature, mould wall temperature and holding pressure), and thus, the TME. Results from analysis of variance for injection-moulded tensile specimens have shown that among the considered processing conditions, the flow rate is the most significant parameter for the Young’s modulus; the flow rate and melt temperature are the most significant for the strain at break; and the holding pressure and flow rate are the most significant for the stress at yield. The yield stress and Young’s modulus were found to be governed mostly by the thermostress index (TSI, related to the orientation of the skin layer), whilst the strain at break depends on both the TSI and the cooling index (CI, associated to the crystallinity degree of the core region). The proposed TMI approach provides predictive capabilities of the mechanical response of injection-moulded components, which is a valuable input during their design stage.

Effect of the Impact Conditions on the Mechanical Properties of Injection-Molded Parts

This work focused on the study of the impact event on molded parts in the framework of automotive components. The influence of the impact conditions and processing parameters on the mechanical behavior of talc-filled polypropylene specimens was analyzed. The specimens were lateral-gate discs produced by injection molding, and the mechanical characterization was performed through instrumented falling weight impact tests concomitantly assisted with high-speed videography. Results analyzed using the analysis of variance (ANOVA) method have shown that from the considered parameters, only the dart diameter and test temperature have significant influence on the falling weight impact properties. Higher dart diameter leads to higher peak force and peak energy results. Conversely, higher levels of test temperatures lead to lower values of peak force and peak energy. By means of high-speed videography, a more brittle fracture was observed for experiments with higher levels of test velocity and dart diameter and lower levels of test temperature. The injection-molding process conditions assessed in this study have an influence on the impact response of moldings, mainly on the deformation capabilities of the moldings.

Variations of the soft tissue thicknesses external to the ribs in Pectus Excavatum patients

Background: Surgical repair of pectus excavatum (PE) has become more popular due to improvements in the minimally invasive Nuss procedure. The pre-surgical assessment of PE patients requires Computerized Tomography (CT), as the malformation characteristics vary from patient to patient. Objective: This work aims to characterize soft tissue thickness (STT) external to the ribs among PE patients. It also presents a comparative analysis between the anterior chest wall surface before and after surgical correction. Methods: Through surrounding tissue segmentation in CT data, STT values were calculated at different lines along the thoracic wall, with a reference point in the intersection of coronal and median planes. The comparative analysis between the two 3D anterior chest surfaces sets a surgical correction influence area (SCIA) and a volume of interest (VOI) based on image processing algorithms, 3D surface algorithms, and registration methods. Results: There are always variations between left and right side STTs (2.54±2.05 mm and 2.95±2.97 mm for female and male patients, respectively). STTs are dependent on age, sex, and body mass index of each patient. On female patients, breast tissue induces additional errors in bar manual

Anotação, numa perspectiva de Direito Penal e de Criminologia, ao Acórdão do Supremo Tribunal de Justiça (português), de 13 de Abril de 2009 [Juiz Conselheiro Rodrigues da COSTA (Relator), Juiz Conselheiro Arménio SOTTOMAYOR (vencido nos termos da declaração junta) e Juiz Conselheiro Mota MIRANDA] - são o «lenocínio» e a prostituição, entre adultos livres, crimes? «Roxanne, you don't have to put on the red light»

Resumo: 1 – Sumário do Acórdão do Supremo Tribunal de Justiça, de 13 de Abril de 2011; 2 – Texto completo do Acórdão do Supremo Tribunal de Justiça, de 13 de Abril de 2009, Juiz Conselheiro Rodrigues da COSTA (Relator), Juiz Conselheiro Arménio SOTTOMAYOR (vencido nos termos da declaração junta) e Juiz Conselheiro Mota MIRANDA: cfr. http://www.dgsi.pt , 26 de Abril de 2011; 3 – Anotação; 3.1 – Introdução à anotação; 3.2 – A questão do suposto «bem jurídico» que seria tutelado pelo crime de «lenocínio» p.p.p.p.p. 169.º do código penal português; 3.2.1 – Ainda a questão do suposto «bem jurídico» que seria tutelado pelo crime de «lenocínio» p.p.p.p.p. 169.º do código penal português: uma maior procura e concretização jurídica e científica; 4 – Conclusões; § Abstract: 1 - Summary of the Sentence of the Supreme Court of Justice, 13 of April of 2011; 2 - Complete text of the Sentence of the Supreme Court of Justice, 13 of April of 2009, Advising Judge Rodrigues da COSTA (Reporter), Advising Judge Arménio SOTTOMAYOR (looser in the terms of the together declaration) and Advising Judge Mota MIRANDA: cfr. http://www.dgsi.pt , 26 of April of 2011; 3 - Notation; 3.1 - Introduction to the notation; 3.2 - The question of the presumption «legally protected interest» that would be tutored person for the crime of «pimpery (“pimping”)» p.p.p.p.p. 169.º of the Portuguese criminal code; 3.2.1 - Still the question of the presumption «legally protected interest» that would be tutored person for the crime of «pimpery» («pimping») p.p.p.p.p. 169.º of the Portuguese criminal code: a bigger search and legal and scientific concretion; 4 - Conclusions;

Variations of the soft tissue thicknesses external to the ribs in pectus excavatum patients

Background: Surgical repair of pectus excavatum (PE) has become more popular due to improvements in the minimally invasive Nuss procedure. The pre-surgical assessment of PE patients requires Computerized Tomography (CT), as the malformation characteristics vary from patient to patient. Objective: This work aims to characterize soft tissue thickness (STT) external to the ribs among PE patients. It also presents a comparative analysis between the anterior chest wall surface before and after surgical correction. Methods: Through surrounding tissue segmentation in CT data, STT values were calculated at different lines along the thoracic wall, with a reference point in the intersection of coronal and median planes. The comparative analysis between the two 3D anterior chest surfaces sets a surgical correction influence area (SCIA) and a volume of interest (VOI) based on image processing algorithms, 3D surface algorithms, and registration methods. Results: There are always variations between left and right side STTs (2.54±2.05 mm and 2.95±2.97 mm for female and male patients, respectively). STTs are dependent on age, sex, and body mass index of each patient. On female patients, breast tissue induces additional errors in bar manual