Modelling the Mechanical Behavior of Polymer-Based Nanocomposites

Molecular dynamics simulations were employed to analyze the mechanical properties of polymer-based nanocomposites with varying nanofiber network parameters. The study was focused on nanofiber aspect ratio, concentration and initial orientation. The reinforcing phase affects the behavior of the polymeric nanocomposite. Simulations have shown that the fiber concentration has a significant effect on the properties, with higher loadings resulting in higher stress levels and higher stiffness, matching the general behavior from experimental knowledge in this field. The results also indicate that, within the studied range, the observed effect of the aspect ratio and initial orientation is smaller than that of the concentration, and that these two parameters are interrelated.

Estimating Local Part Thickness in Midplane Meshes for Finite Element Analysis

Within the development of motor vehicles, crash safety (e.g. occupant protection, pedestrian protection, low speed damageability), is one of the most important attributes. In order to be able to fulfill the increased requirements in the framework of shorter cycle times and rising pressure to reduce costs, car manufacturers keep intensifying the use of virtual development tools such as those in the domain of Computer Aided Engineering (CAE). For crash simulations, the explicit finite element method (FEM) is applied. The accuracy of the simulation process is highly dependent on the accuracy of the simulation model, including the midplane mesh. One of the roughest approximations typically made is the actual part thickness which, in reality, can vary locally. However, almost always a constant thickness value is defined throughout the entire part due to complexity reasons. On the other hand, for precise fracture analysis within FEM, the correct thickness consideration is one key enabler. Thus, availability of per element thickness information, which does not exist explicitly in the FEM model, can significantly contribute to an improved crash simulation quality, especially regarding fracture prediction. Even though the thickness is not explicitly available from the FEM model, it can be inferred from the original CAD geometric model through geometric calculations. This paper proposes and compares two thickness estimation algorithms based on ray tracing and nearest neighbour 3D range searches. A systematic quantitative analysis of the accuracy of both algorithms is presented, as well as a thorough identification of particular geometric arrangements under which their accuracy can be compared. These results enable the identification of each technique’s weaknesses and hint towards a new, integrated, approach to the problem that linearly combines the estimates produced by each algorithm.

Exploring the interdisciplinary process in design education

The work presented herein follows an ongoing research that aims to analyze methodological practices to be applied in Design Education. A reflection about methodological strategies in Design Education and the function of drawing in Design represents the beginning of this study. Then, we developed an interdisciplinary pedagogical experience with the Graphic Design 1st grade students from our institution (IPCA). In the current academic year, 2013/2014, we continue to evolve this project, introducing changes in the initial proposal. Major alterations focused on the aspects that could be strengthened in terms of interdisciplinarity. In this article, the authors describe those changes and discuss the outcomes of the novel proposal. As we have already reported, this investigation follows a reflection about working methods to be adopted in Design Education. This is in accordance with other previously published works that purpose the enlargement of Design into new knowledge fields such as Experience or Service Design, changing not only the role of the graphic designer, but also the skills required to be a professional designer (Alain Findelli, 2001), (Brian Lawson, 2006), (Ciampa-Brewer, 2010). Furthermore, concepts such as cooperation or multidisciplinary design, amongst others, have been frequently debated as design teaching strategies (Heller and Talarico, 2011, pp. 82-85). These educational approaches also have an impact on our research. The analysis of all these authors’ contributions together with a reflection on our teaching practice allowed us to propose an improved interdisciplinary intervention.

The strategic management of creation process and of change: a theoretical contribute from the perspective of tourism

The entrepreneurship and innovation have been gradually gaining ground in the academic community as a field of study. However, the interpretations surrounding fragmented, without a univocal definition. In last decades, tourism has received greater attention from researchers in various sciences, varying only by the different emphases considered: economic, social, cultural and environmental. As other emerging sectors in a modern economy, tourism is a dynamic and ever-changing industry. The study has as purpose to provide a better understanding regarding the essence of entrepreneurship: theoretical and practical implications from the perspective of tourism. Regarding the methodology used here, this is a conceptual paper with a literature review that brings together the major components of entrepreneurship and its implications tourist perspective and conceptual model of the dynamic nature of the Triggering Process and innovation (e.g. iTravey, Interactive Stores, Tourist Transportable Tower).

Artificial neural networks for automatic modelling of the pectus excavatum corrective prosthesis

Pectus excavatum is the most common deformity of the thorax and usually comprises Computed Tomography (CT) examination for pre-operative diagnosis. Aiming at the elimination of the high amounts of CT radiation exposure, this work presents a new methodology for the replacement of CT by a laser scanner (radiation-free) in the treatment of pectus excavatum using personally modeled prosthesis. The complete elimination of CT involves the determination of ribs external outline, at the maximum sternum depression point for prosthesis placement, based on chest wall skin surface information, acquired by a laser scanner. The developed solution resorts to artificial neural networks trained with data vectors from 165 patients. Scaled Conjugate Gradient, Levenberg-Marquardt, Resilient Back propagation and One Step Secant gradient learning algorithms were used. The training procedure was performed using the soft tissue thicknesses, determined using image processing techniques that automatically segment the skin and rib cage. The developed solution was then used to determine the ribs outline in data from 20 patient scanners. Tests revealed that ribs position can be estimated with an average error of about 6.82±5.7 mm for the left and right side of the patient. Such an error range is well below current prosthesis manual modeling (11.7±4.01 mm) even without CT imagiology, indicating a considerable step forward towards CT replacement by a 3D scanner for prosthesis personalization.

The international harmonization process of public accounting in Portugal: the perspective of different stakeholders

This paper investigates the reform of public accounting in Portugal through the IPSAS adoption highlighting the perception of different stakeholders. Two competing theories (NPM and the institutional theory) are used to understand public accounting changes within the Portuguese context. In general, different stakeholders agree with the favorable moment and the context of the reform. The context of financial crises and the great external pressures to cut public deficits and to improve the quality of financial information seem to be the most important factors to stimulate changes in public accounting. In addition, stakeholders recommend the use of different strategies to ensure success.

The internationally standardized process of public accounting: the perspective of different stakeholders in Portugal

New Public Management (NPM) led to great pressures for to introduce and adapt businesslike accounting in the public sector (Hood, 1995; Lapsley, 2008; Lapsley et al., 2009), specially the transition from cash basis to accrual-based accounting. In consequence, since the last 20 years we assist to a movement towards internationally standardized of public sector accounting that led to the publication of 32 International Public Sector Accounting Standards (IPSAS) for all public sector entities from national central governments to local governments (IFAC, 2008). These standards are accrual-basis and they emphasize the balance sheet approach, the fair value measurement and the revenue-expense approach (Hints, 2007). The main innovations are associated with the use of the balance sheet approach and the fair value measurement because, traditionally, public accounting systems are mainly focused on the revenue-expense approach and on historical cost valuation (Oulasvirta, 2014).