Biochemical characterization of serine transport in Leishmania (Leishmania) amazonensis

In addition to its role as a protein component in Leishmania, serine is also a precursor for the synthesis of both phosphatidylserine, which is a membrane molecule involved in parasite invasion and inactivation of macrophages, and sphingolipids, which are necessary for Leishmania to differentiate into its infective forms. We have characterized serine uptake in both promastigote and amastigote forms of Leishmania (Leishmania) amazonensis. In promastigotes, kinetic data show a single, saturable transport system, with a Km of 0.253 +/- 0.01 mM and a maximum velocity of 0.246 +/- 0.04 nmol/min per 107 cells. Serine transport increased linearly with temperature in the range from 20 degrees C to 45 degrees C, allowing the calculation of an activation energy of 7.09 kJ/mol. Alanine, cysteine, glycine, threonine, valine and ethanolamine competed with the substrate at a ten-fold excess concentration. Serine uptake was dependent on pH, with an optimum activity at pH 7.5. The characterization of the serine transport process in amastigotes revealed a transport system with a similar Km, energy of activation and pH response to that found in promastigotes, suggesting that the same transport system is active in both insect vector and mammalian host Leishmania stages. This could constitute an evolutionary mechanism that guarantees the provision of such an essential molecule during host change events, such as differentiation into amastigotes and macrophage invasion, as well as to ensure that the parasite maintains the infection in the mammalian host. (C) 2008 Elsevier B.V. All rights reserved.

Sample stacking in CZE using dynamic thermal junctions I. Analytes with low dpK(a)/dT crossing a single thermally induced pH junction in a BGE with high dpH/dT

The possibility to compress analyte bands at the beginning of CE runs has many advantages. Analytes at low concentration can be analyzed with high signal-to-noise ratios by using the so-called sample stacking methods. Moreover, sample injections with very narrow initial band widths (small initial standard deviations) are sometimes useful, especially if high resolutions among the bands are required in the shortest run time. In the present work, a method of sample stacking is proposed and demonstrated. It is based on BGEs with high thermal sensitive pHs (high dpH/dT) and analytes with low dpK(a)/dT. High thermal sensitivity means that the working pK(a) of the BGE has a high dpK(a)/dT in modulus. For instance, Tris and Ethanolamine have dpH/dT = -0.028/degrees C and -0.029/degrees C, respectively, whereas carboxylic acids have low dpK(a)/dT values, i.e. in the -0.002/degrees C to+0.002/degrees C range. The action of cooling and heating sections along the capillary during the runs affects also the local viscosity, conductivity, and electric field strength. The effect of these variables on electrophoretic velocity and band compression is theoretically calculated using a simple model. Finally, this stacking method was demonstrated for amino acids derivatized with naphthalene-2,3-dicarboxaldehyde and fluorescamine using a temperature difference of 70 degrees C between two neighbor sections and Tris as separation buffer. In this case, the BGE has a high pH thermal coefficient whereas the carboxylic groups of the analytes have low pK(a) thermal coefficients. The application of these dynamic thermal gradients increased peak height by a factor of two (and decreased the standard deviations of peaks by a factor of two) of aspartic acid and glutamic acid derivatized with naphthalene-2,3-dicarboxaldehyde and serine derivatized with fluorescamine. The effect of thermal compression of bands was not observed when runs were accomplished using phosphate buffer at pH 7 (negative control). Phosphate has a low dpH/dT in this pH range, similar to the dK(a)/dT of analytes. It is shown that vertical bar dK(a)/dT-dpH/dT vertical bar >> 0 is one determinant factor to have significant stacking produced by dynamic thermal junctions.