Fretting fatigue in overhead conductors: Rig design and failure analysis of a Grosbeak aluminium cable steel reinforced conductor

The performance optimisation of overhead conductors depends on the systematic investigation of the fretting fatigue mechanisms in the conductor/clamping system. As a consequence, a fretting fatigue rig was designed and a limited range of fatigue tests was carried out at the middle high cycle fatigue regime in order to access an exploratory S-N curve for a Grosbeak conductor, which was mounted on a mono-articulated aluminium clamping system. Subsequent to these preliminary fatigue tests, the components of the conductor/clamping system, such as ACSR conductor, upper and lower clamps, bolt and nuts, were subjected to a failure analysis procedure in order to investigate the metallurgical free variables interfering on the fatigue test results, aiming at the optimisation of the testing reproducibility. The results indicated that the rupture of the planar fracture surfaces observed in the external At strands of the conductor tested under lower bending amplitude (0.9 mm) occurred by fatigue cracking (I mm deep), followed by shear overload. The V-type fracture surfaces observed in some At strands of the conductor tested under higher bending amplitude (1.3 mm) were also produced by fatigue cracking (approximately 400 mu m deep), followed by shear overload. Shear overload fracture (45 degrees fracture surface) was also observed on the remaining At wires of the conductor tested under higher bending amplitude (1.3 mm). Additionally, the upper and lower Al-cast clamps presented microstructure-sensitive cracking, which was folowed by particle detachment and formation of abrasive debris on the clamp/conductor tribo-interface, promoting even further the fretting mechanism. The detrimental formation of abrasive debris might be inhibited by the selection of a more suitable class of as-cast At alloy for the production of clamps. Finally, the bolt/nut system showed intense degradation of the carbon steel nut (fabricated in ferritic-pearlitic carbon steel, featuring machined threads with 190 HV), with intense plastic deformation and loss of material. Proper selection of both the bolt and nut materials and the finishing processing might prevent the loss in the clamping pressure during the fretting testing. It is important to control the specification of these components (clamps, bolt and nuts) prior to the start of large scale fretting fatigue testing of the overhead conductors in order to increase the reproducibility of this assessment. (c) 2008 Elsevier Ltd. All rights reserved.

Development and characterization of microsatellite loci in the marsh deer (Blastocerus dichotomus Cervidae)

Marsh deer (Blastocerus dichotomus) is one of the most exposed large mammals in South America. To aid in the conservation management of the species, nine polymorphic microsatellite loci were isolated and tested on up to 50 animals, showing 3-12 alleles and expected heterozygosity values varying from 0.69 to 0.89. These markers should be of considerable utility in future population and ecological genetics studies of this species. The marsh deer (Blastocerus dichotomus) is the biggest South American species of deer. Originally distributed across a large part of South America, stretching from the south bank of the Amazon river to northern Argentina, significant wild populations are now restricted to the Pantanal, swamplands that cover about 40% of southwest Brazil. The marsh deer is listed as Vulnerable on the Red List of the IUCN. Three populations of the species from three areas in the Parana River basin (between the states of Sao Paulo and Mato Grosso do Sul) were recently studied by observing protein polymorphism at 17 loci (Oliveira et al. 2005). Now we are presenting data about isolation of microsatellite markers to improve the results regarding population structure.

Trade unions and the economic performance of brazilian establishments

Este artigo analisa, pela primeira vez na literatura, o impacto dos sindicatos de trabalhadores em vários indicadores de desempenho econômico de firmas industriais brasileiras. Realizou-se uma pesquisa retrospectiva sobre a densidade sindical de 1000 estabelecimentos industriais brasileiros e seus resultados foram combinados aos indicadores de desempenho econômico da Pesquisa Industrial Anual (PIA) de 1990 a 2000. Os resultados indicam que a relação entre a densidade sindical na firma e seus salários, emprego e produtividade, é não-linear, ou seja, um aumento no grau de sindicalização leva a um melhor desempenho, porém a taxas decrescentes. Observou-se, também, uma relação negativa entre sindicalização e rentabilidade. Finalmente, estabelecimentos que introduziram mecanismos de 'participação nos lucros' aumentaram sua produtividade e rentabilidade no período e pagaram maiores salários nas firmas onde o grau de sindicalização era maior.

Uso de álcool e drogas e contextos sociais da violência

Contextos de violência e de consumo de álcool e drogas são nesse texto tratados a partir dos conceitos de sociedade de risco e reflexividade social, são expostas e discutidas pesquisas empíricas que relacionaram as duas situações, destacando-se a necessidade de não se estabelecer determinações entre esses contextos. Conclui-se que há necessidade de aprofundar a discussão da redução de riscos sociais tanto em relação ao consumo como em relação à violência