Understanding Wax Printing: A Simple Micropatterning Process for Paper-Based Microfluidics

This technical note describes a detailed study on wax printing, a simple and inexpensive method for fabricating microfluidic devices in paper using a commercially available printer and hot plate. The printer prints patterns of solid wax on the surface of the paper, and the hot plate melts the wax so that it penetrates the full thickness of the paper. This process creates complete hydrophobic barriers in paper that define hydrophilic channels, fluid reservoirs, and reaction zones. The design of each device was based on a simple equation that accounts for the spreading of molten wax in paper.

Open cluster survival within the solar circle: Teutsch 145 and Teutsch 146 star

Teutsch 145 and Teutsch 146 are shown to be open clusters (OCs) orbiting well inside the solar circle, a region where several dynamical processes combine to disrupt most OCs on a time-scale of a few 108 yr. BVI photometry from the GALILEO telescope is used to investigate the nature and derive the fundamental and structural parameters of the optically faint and poorly known OCs Teutsch 145 and 146. These parameters are computed by means of field-star-decontaminated colour-magnitude diagrams and stellar radial density profiles (RDPs). Cluster mass estimates are made based on the intrinsic mass functions (MFs). We derive the ages 200+100(-50) and 400 +/- 100 Myr, and the distances from the Sun d(circle dot) = 2.7 +/- 0.3 and 3.8 +/- 0.2 kpc, respectively, for Teutsch 145 and 146. Their integrated apparent and absolute magnitudes are m(V) approximate to 12.4 and 13.3 and M(V) approximate to -5.6 and -5.3. The MFs (detected for stars with m greater than or similar to 1 M(circle dot)) have slopes similar to Salpeter`s initial mass function. Extrapolated to the H-burning limit, the MFs would produce total stellar masses of similar to 1400 M(circle dot), typical of relatively massive OCs. Both OCs are located deep into the inner Galaxy and close to the Crux-Scutum arm. Since cluster-disruption processes are important, their primordial masses must have been higher than the present-day values. The conspicuous stellar density excess observed in the innermost bin of both RDPs might reflect the dynamical effects induced by a few 108 yr of external tidal stress.

Early Onset Obsessive-Compulsive Disorder With and Without Tics

Introduction: Research suggests that obsessive-compulsive disorder (OCD) is not a unitary entity, but rather a highly heterogeneous condition, with complex and variable clinical manifestations. Objective: The aims of this study were to compare clinical and demographic characteristics of OCD patients with early and late age of onset of obsessive-compulsive symptoms (OCS); and to compare the same features in early onset OCD with and without tics. The independent impact of age at onset and presence of tics on comorbidity patterns was investigated. Methods: Three hundred and thirty consecutive outpatients meeting Diagnostic and Statistical Manual of Mental Disorders, Fourth Edition criteria for OCD were evaluated: 160 patients belonged to the ""early onset"" group (EOG): before 11 years of age, 75 patients had an ""intermediate onset"" (IOG), and 95 patients were from the ""late onset"" group (LOG): after 18 years of age. From the 160 EOG, 60 had comorbidity with tic disorders. The diagnostic instruments used were: the Yale-Brown Obsessive Compulsive Scale and the Dimensional Yale-Brown Obsessive Compulsive Scale (DY-BOCS), Yale Global Tics Severity Scale; and Structured Clinical Interview for DSM-IV Axis I Disorders-patient edition. Statistical tests used were: Mann-Whitney, full Bayesian significance test, and logistic regression. Results: The EOG had a predominance of males, higher frequency of family history of OCS, higher mean scores on the ""aggression/violence"" and ""miscellaneous"" dimensions, and higher mean global DY-BOCS scores. Patients with EOG without tic disorders presented higher mean global DY-BOCS scores and higher mean scores in the ""contamination/cleaning"" dimension. Conclusion: The current results disentangle some of the clinical overlap between early onset OCD with and without tics. CNS Spectr. 2009; 14(7):362-370

Obsessive-compulsive disorder: Influence of age at onset on comorbidity patterns

Purpose. - This study investigates the influence of age at onset of OCS on psychiatric comorbidities, and tries to establish a cut-off point for age at onset. Methods. - Three hundred and thirty OCD patients were consecutively recruited and interviewed using the following structured interviews: Yale-Brown Obsessive Compulsive Scale; Yale Global Tic Severity Scale and the Structured Clinical Interview for DSM-IV. Data were analyzed with regression and cluster analysis. Results. - Lower age at onset was associated with a higher probability of having comorbidity with tic, anxiety, somatoform, eating and impulse-control disorders. Longer illness duration was associated with lower chance of having tics. Female gender was associated with anxiety, eating and impulse-control disorders. Tic disorders were associated with anxiety disorders and attention-deficit/hyperactivity disorder. No cutoff age at onset was found to clearly divide the sample in homogeneous subgroups. However, cluster analyses revealed that differences started to emerge at the age of 10 and were more pronounced at the age of 17, suggesting that these were the best cut-off points on this sample. Conclusions. - Age at onset is associated with specific comorbidity patterns in OCD patients. More prominent differences are obtained when analyzing age at onset as an absolute value. (C) 2008 Elsevier Masson SAS. All rights reserved.

Flow injection analysis of ethyl xanthate by gas diffusion and UV detection as CS(2) for process monitoring of sulfide ore flotation

A sensitive and robust analytical method for spectrophotometric determination of ethyl xanthate, CH(3)CH(2)OCS(2)(-) at trace concentrations in pulp solutions from froth flotation process is proposed. The analytical method is based on the decomposition of ethyl xanthate. EtX(-), with 2.0 mol L(-1) HCl generating ethanol and carbon disulfide. CS(2). A gas diffusion cell assures that only the volatile compounds diffuse through a PTFE membrane towards an acceptor stream of deionized water, thus avoiding the interferences of non-volatile compounds and suspended particles. The CS(2) is selectively detected by UV absorbance at 206 nm (epsilon = 65,000 L mol(-1) cm(-1)). The measured absorbance is directly proportional to EtX(-) concentration present in the sample solutions. The Beer`s law is obeyed in a 1 x 10(-6) to 2 x 10(-4) mol L(-1) concentration range of ethyl xanthate in the pulp with an excellent correlation coefficient (r = 0.999) and a detection limit of 3.1 x 10(-7) mol L(-1), corresponding to 38 mu g L. At flow rates of 200 mu L min(-1) of the donor stream and 100 mu L min(-1) of the acceptor channel a sampling rate of 15 injections per hour could be achieved with RSD < 2.3% (n = 10, 300 mu L injections of 1 x 10(-5) mol L(-1) EtX(-)). Two practical applications demonstrate the versatility of the FIA method: (i) evaluation the free EtX(-) concentration during a laboratory study of the EtX(-) adsorption capacity on pulverized sulfide ore (pyrite) and (ii) monitoring of EtX(-) at different stages (from starting load to washing effluents) of a flotation pilot plant processing a Cu-Zn sulfide ore. (C) 2010 Elsevier By. All rights reserved.

Fabrication and integration of planar electrodes for contactless conductivity detection on polyester-toner electrophoresis microchips

In this report, we describe the microfabrication and integration of planar electrodes for contactless conductivity detection on polyester-toner (PT) electrophoresis microchips using toner masks. Planar electrodes were fabricated by three simple steps: (i) drawing and laser-printing the electrode geometry on polyester films, (ii) sputtering deposition onto substrates, and (iii) removal of toner layer by a lift-off process. The polyester film with anchored electrodes was integrated to PT electrophoresis microchannels by lamination at 120 degrees C in less than 1 min. The electrodes were designed in an antiparallel configuration with 750 mu m width and 750 gm gap between them. The best results were recorded with a frequency of 400 kHz and 10 V-PP using a sinusoidal wave. The analytical performance of the proposed microchip was evaluated by electrophoretic separation of potassium, sodium and lithium in 150 mu m wide x 6 mu m deep microchannels. Under an electric field of 250 V/cm the analytes were successfully separated in less than 90 s with efficiencies ranging from 7000 to 13 000 plates. The detection limits (S/N = 3) found for K+, Na+, and Li+ were 3.1, 4.3, and 7.2 mu mol/L, respectively. Besides the low-cost and instrumental simplicity, the integrated PT chip eliminates the problem of manual alignment and gluing of the electrodes, permitting more robustness and better reproducibility, therefore, more suitable for mass production of electrophoresis microchips.

Dynamic Solid Phase DNA Extraction and PCR Amplification in Polyester-Toner Based Microchip

A variety of substrates have been used for fabrication of microchips for DNA extraction, PCR amplification, and DNA fragment separation, including the more conventional glass and silicon as well as alternative polymer-based materials. Polyester represents one such polymer, and the laser-printing of toner onto polyester films has been shown to be effective for generating polyester-toner (PeT) microfluidic devices with channel depths on the order of tens of micrometers. Here, we describe a novel and simple process that allows for the production of multilayer, high aspect-ratio PeT microdevices with substantially larger channel depths. This innovative process utilizes a CO(2) laser to create the microchannel in polyester sheets containing a uniform layer of printed toner, and multilayer devices can easily be constructed by sandwiching the channel layer between uncoated cover sheets of polyester containing precut access holes. The process allows the fabrication of deep channels, with similar to 270 mu m, and we demonstrate the effectiveness of multilayer PeT microchips for dynamic solid phase extraction (dSPE) and PCR amplification. With the former, we found that (i) more than 65% of DNA from 0.6 mu L of blood was recovered, (ii) the resultant DNA was concentrated to greater than 3 ng/mu L., (which was better than other chip-based extraction methods), and (iii) the DNA recovered was compatible with downstream microchip-based PCR amplification. Illustrative of the compatibility of PeT microchips with the PCR process, the successful amplification of a 520 bp fragment of lambda-phage DNA in a conventional thermocycler is shown. The ability to handle the diverse chemistries associated with DNA purification and extraction is a testimony to the potential utility of PeT microchips beyond separations and presents a promising new disposable platform for genetic analysis that is low cost and easy to fabricate.

Comparison of the analytical performance of electrophoresis microchannels fabricated in PDMS, glass, and polyester-toner

This paper compares the analytical performance of microchannels fabricated in PDMS, glass, and polyester-toner for electrophoretic separations. Glass and PDMS chips were fabricated using well-established photolithographic and replica-molding procedures, respectively. PDMS channels were sealed against three different types of materials: native PDMS, plasma-oxidized PDMS, and glass. Polyester-toner chips were micromachined by a direct-printing process using an office laser printer. All microchannels were fabricated with similar dimensions according to the limitations of the direct-printing process (width/depth 150 mu m/12 mu m). LIF was employed for detection to rule out any losses in separation efficiency due to the detector configuration. Two fluorescent dyes, coumarin and fluorescein, were used as model analytes. Devices were evaluated for the following parameters related to electrophoretic separations: EOF, heat dissipation, injection reproducibility, separation efficiency, and adsorption to channel wall.