Effect of repeated disinfections by microwave energy on the physical and mechanical properties of denture base acrylic resins

The present study evaluated the effect of repeated simulated microwave disinfection on physical and mechanical properties of Clássico, Onda-Cryl and QC-20 denture base acrylic resins. Aluminum patterns were included in metallic or plastic flasks with dental stone following the traditional packing method. The powder/liquid mixing ratio was established according to the manufacturer's instructions. After water-bath polymerization at 74ºC for 9 h, boiling water for 20 min or microwave energy at 900 W for 10 min, the specimens were deflasked after flask cooling and finished. Each specimen was immersed in 150 mL of distilled water and underwent 5 disinfection cycles in a microwave oven set at 650 W for 3 min. Non-disinfected and disinfected specimens were subjected to the following tets: Knoop hardness test was performed with 25 g load for 10 s, impact strength test was done using the Charpy system with 40 kpcm, and 3-point bending test (flexural strength) was performed at a crosshead speed of 0.5 mm/min until fracture. Data were analyzed statistically by ANOVA and Tukey's test (α= 0.05%). Repeated simulated microwave disinfections decreased the Knoop hardness of Clássico and Onda-Cryl resins and had no effect on the impact strength of QC-20. The flexural strength was similar for all tested resins.

Natural occurrence, biological activities and synthesis of eight-, nine-, and eleven-membered ring lactones

The natural occurrence, biological activities and synthetic approaches to natural eight-, nine-, and eleven-membered lactones is reviewed. These medium ring lactones are grouped according to ring size, and their syntheses are discussed. The structures of some natural products early identified as medium-ring lactones were revised after total synthesis.

Situação epidemiológica da brucelose bovina no Estado de Goiás

Realizou-se um estudo para caracterizar a situação epidemiológica da brucelose no Estado de Goiás. O Estado foi estratificado em três circuitos produtores. Em cada circuito foram amostradas aleatoriamente 300 propriedades e, dentro dessas, foi escolhido de forma aleatória um número pré-estabelecido de animais, dos quais foi obtida uma amostra de sangue. No total, foram amostrados 10.744 animais, provenientes de 900 propriedades. Em cada propriedade visitada aplicou-se um questionário epidemiológico para verificar o tipo de exploração e as práticas de criação e sanitárias que poderiam estar associadas ao risco de infecção pela doença. O protocolo de testes utilizado foi o da triagem com o teste do antígeno acidificado tamponado e a confirmação dos positivos com o teste do 2-mercaptoetanol. O rebanho foi considerado positivo quando pelo menos um animal foi reagente às duas provas sorológicas. No estrato 1, a prevalência foi de 7,7% [4,7-10,7%] para propriedades, e de 1,4% [0,99-1,7%] para animais. No estrato 2, foi de 19,5% [15,0-24,0%] para propriedades e de 2,6% [2,0-3,1%] para animais. No estrato 3, foi de 21,4% [16,7-26,1] para propriedades e 4,3% [3,7-5,0%] para animais. A prevalência obtida para o Estado foi de 17,5% [14,9-20,2%] para propriedades e de 3,0% [2,7-3,3%] para animais. Os fatores de risco (odds ratio, OR) associados à condição de foco, segundo a análise multivariada, foram: compra de reprodutores a comerciantes de gado (OR = 2,06 [1,12-3,52]), ocorrência de abortos nos últimos 12 meses (OR = 5,83 [3,86-8,8]) e prática de vacinação contra brucelose (OR = 2,07 [1,38-3,09]). Tanto a ocorrência de aborto quanto a vacinação são, neste caso, consequência da presença de brucelose no rebanho.

Fontes orgânicas e inorgânicas de zinco e cobre como melhoradores de desempenho em leitões desmamados

Foram conduzidos dois experimentos para avaliar fontes orgânicas e inorgânicas de zinco e cobre nas dietas e seus efeitos no desempenho de leitões desmamados aos 21 dias de idade. Em cada experimento, foram utilizados 90 leitões em delineamento experimental de blocos ao acaso, com cinco dietas, seis repetições e três animais por parcela. As dietas utilizadas nos experimentos 1 e 2 continham 120 ppm de zinco e 10 ppm de cobre na forma de sulfato. No experimento 1, foram suplementadas com 0, 300, 600 e 900 ppm de zinco na forma orgânica ou 2.400 ppm na forma de óxido (ZnO) e, no experimento 2, com 0, 50, 100 e 150 ppm de cobre na forma orgânica ou 240 ppm de cobre na forma de sulfato (CuSO4 H2O). No experimento 1, os níveis de zinco de fonte orgânica tiveram efeito linear no consumo de ração e no ganho de peso nos períodos de 0 a 15 dias e de 0 a 21 dias pós-desmame. O ganho de peso nas fases de 0 a 35 dias e de 0 a 42 dias pós-desmame e o consumo de ração dos leitões que receberam a dieta com 900 ppm de zinco de fonte orgânica não diferiram dos valores observados naqueles que receberam a dieta com 2.400 ppm de zinco na forma inorgânica. A suplementação da dieta com zinco na forma orgânica (900 ppm) ou inorgânica (2.400 ppm) aumentou o consumo de ração e o ganho de peso de leitões nas primeiras três semanas após o desmame. A suplementação da dieta com 2.400 ppm de zinco na forma inorgânica reduziu a incidência de diarreia nas primeiras três semanas pós-desmame. No experimento 2, os níveis de cobre de fonte orgânica tiveram efeito quadrático no consumo de ração dos leitões nos períodos de 0 a 31 e de 0 a 40 dias pós-desmame. A suplementação da dieta com cobre, tanto de fonte orgânica (90 ppm) como inorgânica (240 ppm), aumenta o consumo de ração e o ganho de peso de leitões nos primeiros 40 dias pós-desmame.

Lisina digestível e zinco orgânico para frangos de corte machos na fase de 22 a 42 dias de idade

Os efeitos dietéticos de lisina digestível e zinco quelato para frangos de corte machos entre 22 e 42 dias de idade foram avaliados em dois ensaios experimentais. Adotou-se o delineamento inteiramente casualizado em arranjo fatorial 5 × 2, com cinco níveis de lisina (0,841; 0,876; 0,997; 1,022 e 1,030%) e dois de zinco (43 e 243 ppm). No primeiro ensaio, utilizaram-se 900 aves com peso médio inicial de 957,4 g distribuídas em parcelas experimentais de 30 aves e três repetições e, no segundo ensaio, 180 frangos com peso médio inicial de 866,22 g, divididos em parcelas de três aves e seis repetições. As características avaliadas foram desempenho, rendimento de cortes e composição corporal (1º ensaio), balanço de nitrogênio e digestibilidade aparente das dietas (2º ensaio). Houve interação entre os níveis de lisina e zinco para o ganho de peso, a conversão alimentar, a matéria seca ingerida e o balanço energético. Os rendimentos de peito, coxa e sobrecoxa tiveram aumentos lineares em resposta ao acréscimo no nível de lisina digestível na dieta. O melhor desempenho foi obtido com o nível de 0,997% de lisina digestível (ou 1,134% lisina total) e de 43 ppm de zinco. Para maior rendimento dos cortes, o nível de lisina digestível recomendável deve ser no mínimo 1,002% (ou 1,139% de lisina total), independentemente dos níveis de zinco quelato. A maior inclusão de zinco em dietas para frangos de corte dos 22 aos 42 dias de idade não melhora a utilização da lisina na dieta e aumenta a deposição de gordura corporal.

Methodology to forecast the harvest date of banana bunches

Introduction. This method is used to forecast the harvest date of banana bunches from as early as the plant shooting stage. It facilitates the harvest of bunches with the same physiological age. The principle, key advantages, time required and expected results are presented. Materials and methods. Details of the four steps of the method ( installation of the temperature sensor, tagging bunches at the flowering stage, temperature sum calculation and estimation of bunch harvest date) are described. Possible problems are discussed. Results. The application of the method allows drawing a curve of the temperature sum accumulated by the bunches which have to be harvested at exactly 900 degree-days physiological age.

Detection of high-velocity material from the wind-wind collision zone of Eta Carinae across the 2009.0 periastron passage

We report near-infrared spectroscopic observations of the Eta Carinae massive binary system during 2008-2009 using the CRIRES spectrograph mounted on the 8m UT 1 Very Large Telescope (VLT Antu). We detect a strong, broad absorption wing in He I lambda 10833 extending up to -1900 km s(-1) across the 2009.0 spectroscopic event. Analysis of archival Hubble Space Telescope/Space Telescope Imaging Spectrograph ultraviolet and optical data identifies a similar high-velocity absorption (up to -2100 km s(-1)) in the ultraviolet resonance lines of Si IV lambda lambda 1394, 1403 across the 2003.5 event. Ultraviolet resonance lines from low-ionization species, such as Si II lambda lambda 1527, 1533 and CII lambda lambda 1334, 1335, show absorption only up to -1200 km s(-1), indicating that the absorption with velocities -1200 to -2100 km s(-1) originates in a region markedly more rapidly moving and more ionized than the nominal wind of the primary star. Seeing-limited observations obtained at the 1.6m OPD/LNA telescope during the last four spectroscopic cycles of Eta Carinae (1989-2009) also show high-velocity absorption in He I lambda 10833 during periastron. Based on the large OPD/LNA dataset, we determine that material with velocities more negative than -900 km s(-1) is present in the phase range 0.976 <= phi <= 1.023 of the spectroscopic cycle, but absent in spectra taken at phi <= 0.947 and phi >= 1.049. Therefore, we constrain the duration of the high-velocity absorption to be 95 to 206 days (or 0.047 to 0.102 in phase). We propose that the high-velocity absorption component originates in shocked gas in the wind-wind collision zone, at distances of 15 to 45 AU in the line-of-sight to the primary star. With the aid of three-dimensional hydrodynamical simulations of the wind-wind collision zone, we find that the dense high-velocity gas is along the line-of-sight to the primary star only if the binary system is oriented in the sky such that the companion is behind the primary star during periastron, corresponding to a longitude of periastron of omega similar to 240 degrees-270 degrees. We study a possible tilt of the orbital plane relative to the Homunculus equatorial plane and conclude that our data are broadly consistent with orbital inclinations in the range i = 40 degrees-60 degrees.

Both accurate and precise gf-values for Fe II lines

We present a new set of oscillator strengths for 142 Fe II lines in the wavelength range 4000-8000 angstrom. Our gf-values are both accurate and precise, because each multiplet was globally normalized using laboratory data ( accuracy), while the relative gf-values of individual lines within a given multiplet were obtained from theoretical calculations ( precision). Our line list was tested with the Sun and high-resolution (R approximate to 10(5)), high-S/N (approximate to 700-900) Keck+HIRES spectra of the metal-poor stars HD 148816 and HD 140283, for which line-to-line scatter (sigma) in the iron abundances from Fe II lines as low as 0.03, 0.04, and 0.05 dex are found, respectively. For these three stars the standard error in the mean iron abundance from Fe II lines is negligible (sigma(mean) <= 0.01 dex). The mean solar iron abundance obtained using our gf-values and different model atmospheres is A(Fe) = 7.45(sigma = 0.02).

Espacialização da temperatura do ar anual no estado de Alagoas com diferentes modelos digitais de elevação e resoluções espaciais

The aim of this study was to establish a digital elevation model and its horizontal resolution to interpolate the annual air temperature for the Alagoas State by means of multiple linear regression models. A multiple linear regression model was adjusted to series (11 to 34 years) of annual air temperatures obtained from 28 weather stations in the states of Alagoas, Bahia, Pernambuco and Sergipe, in the Northeast of Brazil, in function of latitude, longitude and altitude. The elevation models SRTM and GTOPO30 were used in the analysis, with original resolutions of 90 and 900 m, respectively. The SRTM was resampled for horizontal resolutions of 125, 250, 500, 750 and 900 m. For spatializing the annual mean air temperature for the state of Alagoas, a multiple linear regression model was used for each elevation and spatial resolution on a grid of the latitude and longitude. In Alagoas, estimates based on SRTM data resulted in a standard error of estimate (0.57 degrees C) and dispersion (r(2) = 0.62) lower than those obtained from GTOPO30 (0.93 degrees C and 0.20). In terms of SRTM resolutions, no significant differences were observed between the standard error (0.55 degrees C; 750 m - 0.58 degrees C; 250m) and dispersion (0.60; 500 m - 0.65; 750 m) estimates. The spatialization of annual air temperature in Alagoas, via multiple regression models applied to SRTM data showed higher concordance than that obtained with the GTOPO30, independent of the spatial resolution.

Synchrotron X-ray powder diffraction study of the tetragonal-cubic phase transition in nanostructured ZrO2-Sc2O3 solid solutions

The transition between tetragonal and cubic phases in nanostructured ZrO2-Sc2O3 solid solutions by high-temperature X-ray powder diffraction using synchrotron radiation is presented. ZrO2-8 and 11 mol% Sc2O3 nanopowders that exhibit the t'- and t ''-forms of the tetragonal phase, respectively, were synthesized by a stoichiometric nitrate-lysine gel-combustion route. The average crystallite size treated at 900 degrees C was about 25 nm for both compositions. Our results showed that t'-t '' and t ''-cubic transitions take place for the 8 and 11 mol% Sc2O3 samples, respectively. (C) 2008 International Centre for Diffraction Data.

Study of the optical and magnetic properties of pyrimidine in water combining PCM and QM/MM methodologies

The solvent effects on the low-lying absorption spectrum and on the (15)N chemical shielding of pyrimidine in water are calculated using the combined and sequential Monte Carlo simulation and quantum mechanical calculations. Special attention is devoted to the solute polarization. This is included by an iterative procedure previously developed where the solute is electrostatically equilibrated with the solvent. In addition, we verify the simple yet unexplored alternative of combining the polarizable continuum model (PCM) and the hybrid QM/MM method. We use PCM to obtain the average solute polarization and include this in the MM part of the sequential QM/MM methodology, PCM-MM/QM. These procedures are compared and further used in the discrete and the explicit solvent models. The use of the PCM polarization implemented in the MM part seems to generate a very good description of the average solute polarization leading to very good results for the n-pi* excitation energy and the (15)N nuclear chemical shield of pyrimidine in aqueous environment. The best results obtained here using the solute pyrimidine surrounded by 28 explicit water molecules embedded in the electrostatic field of the remaining 472 molecules give the statistically converged values for the low lying n-pi* absorption transition in water of 36 900 +/- 100 (PCM polarization) and 36 950 +/- 100 cm(-1) (iterative polarization), in excellent agreement among one another and with the experimental value observed with a band maximum at 36 900 cm(-1). For the nuclear shielding (15)N the corresponding gas-water chemical shift obtained using the solute pyrimidine surrounded by 9 explicit water molecules embedded in the electrostatic field of the remaining 491 molecules give the statistically converged values of 24.4 +/- 0.8 and 28.5 +/- 0.8 ppm, compared with the inferred experimental value of 19 +/- 2 ppm. Considering the simplicity of the PCM over the iterative polarization this is an important aspect and the computational savings point to the possibility of dealing with larger solute molecules. This PCM-MM/QM approach reconciles the simplicity of the PCM model with the reliability of the combined QM/MM approaches.

The role of quantum confinement and crystalline structure on excitonic lifetimes in silicon nanoclusters

The emission energy dependence of the photoluminescence (PL) decay rate at room temperature has been studied in Si nanoclusters (Si-ncl) embedded in Si oxide matrices obtained by thermal annealing of substoichiometric Si oxide layers Si(y)O(1-y), y=(0.36,0.39,0.42), at various annealing temperatures (T(a)) and gas atmospheres. Raman scattering measurements give evidence for the formation of amorphous Si-ncl at T(a)=900 degrees C and of crystalline Si-ncl for T(a)=1000 degrees C and 1100 degrees C. For T(a)=1100 degrees C, the energy dispersion of the PL decay rate does not depend on sample fabrication conditions and follows previously reported behavior. For lower T(a), the rate becomes dependent on fabrication conditions and less energy dispersive. The effects are attributed to exciton localization and decoherence leading to the suppression of quantum confinement and the enhancement of nonradiative recombination in disordered and amorphous Si-ncl. (C) 2010 American Institute of Physics. [doi: 10.1063/1.3457900]

Regional scale analysis of landform configuration with base-level (isobase) maps

Base-level maps (or ""isobase maps"", as originally defined by Filosofov, 1960), express a relationship between valley order and topography. The base-level map can be seen as a ""simplified"" version of the original topographic surface, from which the ""noise"" of the low-order stream erosion was removed. This method is able to identify areas with possible tectonic influence even within lithologically uniform domains. Base-level maps have been recently applied in semi-detail scale (e.g., 1:50 000 or larger) morphotectonic analysis. In this paper, we present an evaluation of the method's applicability in regional-scale analysis (e.g., 1:250 000 or smaller). A test area was selected in northern Brazil, at the lower course of the Araguaia and Tocantins rivers. The drainage network extracted from SRTM30_PLUS DEMs with spatial resolution of approximately 900 m was visually compared with available topographic maps and considered to be compatible with a 1:1,000 000 scale. Regarding the interpretation of regional-scale morphostructures, the map constructed with 2nd and 3rd-order valleys was considered to present the best results. Some of the interpreted base-level anomalies correspond to important shear zones and geological contacts present in the 1:5 000 000 Geological Map of South America. Others have no correspondence with mapped Precambrian structures and are considered to represent younger, probably neotectonic, features. A strong E-W orientation of the base-level lines over the inflexion of the Araguaia and Tocantins rivers, suggest a major drainage capture. A N-S topographic swath profile over the Tocantins and Araguaia rivers reveals a topographic pattern which, allied with seismic data showing a roughly N-S direction of extension in the area, lead us to interpret this lineament as an E-W, southward-dipping normal fault. There is also a good visual correspondence between the base-level lineaments and geophysical anomalies. A NW-SE lineament in the southeast of the study area partially corresponds to the northern border of the Mosquito lava field, of Jurassic age, and a NW-SE lineament traced in the northeastern sector of the study area can be interpreted as the Picos-Santa Ines lineament, identifiable in geophysical maps but with little expression in hypsometric or topographic maps.

Characterizing suspended sediments from the Piracicaba River Basin by means of k(0)-INAA

The inorganic chemical characterization of suspended sediments is of utmost relevance for the knowledge of the dynamics and movement of chemical elements in the aquatic and wet ecosystems. Despite the complexity of the effective design for studying this ecological compartment, this work has tested a procedure for analyzing suspended sediments by instrumental neutron activation analysis, k(0) method (k(0)-INAA). The chemical elements As, Ba, Br, Ca, Ce, Co, Cr, Cs, Eu, Fe, Hf, Fig, K, La, Mo, Na, Ni, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, Yb and Zn were quantified in the suspended sediment compartment by means of k(0)-INAA. When compared with World Average for rivers, high mass fractions of Fe (222,900 mg/kg), Ba (4990 mg/kg), Zn (1350 mg/kg), Cr (646 mg/kg), Co (74.5 mg/kg), Br (113 mg/kg) and Mo (31.9 mg/kg) were quantified in suspended sediments from the Piracicaba River, the Piracicamirim Stream and the Marins Stream. Results of the principal component analysis for standardized chemical element mass fractions indicated an intricate correlation among chemical elements evaluated, as a response of the contribution of natural and anthropogenic sources of chemical elements for ecosystems. (C) 2010 Elsevier B.V. All rights reserved.

Emissions from the premixed combustion of gasified polyethylene

An investigation was conducted on pollutants emitted from steady-state, steady-flow gasification and combustion of polyethylene (PE) in a two-stage furnace. The polymer, in pulverized form, was first pyrolyzed at 1000 degrees C, and subsequently, its gaseous pyrolyzates were burned, upon mixing with air at high temperatures (900-1100 degrees C). The motivation for this indirect type of burning PE was to attain nominally premixed combustion of the pyrolyzate gases with air, thereby achieving lower pollutant emissions than those emanating from the direct burning of the solid PE polymer. This work assessed the effluents of the two-stage furnace and examined the effects of the combustion temperature, as well as the polymer feed rate and the associated fuel/air equivalence ratio (0.3 < phi < 1.4). It was found that, whereas the yield of pyrolysis gas decreased with an increasing polymer feed rate, its composition was nearly independent of the feed rate. CO2 emissions peaked at an equivalence ratio near unity, while the CO emissions increased with an increasing equivalence ratio. The total light volatile hydrocarbon and semivolatile polycyclic aromatic hydrocarbon (PAH) emissions of combustion increased with an increasing equivalence ratio. The generated particulates were mostly submicrometer in size. Overall, PAH and soot emissions from this indirect burning of PE were an order of magnitude lower than corresponding emissions from the direct burning of the solid polymer, obtained previously in this laboratory using identical sampling and analytical techniques. Because pyrolysis of this polymer requires a nominal heat input that amounts to only a diminutive fraction of the heat released during its combustion, implementation of this technique is deemed advantageous.