In vitro study of the pulp chamber temperature rise during light-activated bleaching

This study evaluated in vitro the pulp chamber temperature rise induced by the light-activated dental bleaching technique using different light sources. The root portions of 78 extracted sound human mandibular incisors were sectioned approximately 2 mm below the cementoenamel junction. The root cavities of the crowns were enlarged to facilitate the correct placing of the sensor into the pulp chamber. Half of specimens (n=39) was assigned to receive a 35% hydrogen peroxide gel on the buccal surface and the other halt (n=39) not to receive the bleaching agent. Three groups (n=13) were formed for each condition (bleach or no bleach) according to the use of 3 light sources recommended for dental bleaching: a light-emitting diode (LED)laser system, a LED unit and a conventional halogen light. The light sources were positioned perpendicular to the buccal surface at a distance of 5 mm and activated during 30 s. The differences between the initial and the highest temperature readings for each specimen were obtained, and, from the temperature changes, the means for each specimen and each group were calculated. The values of temperature rise were compared using Kruskal-Wallis test at 1% significance level. Temperature rise varied significantly depending on the light-curing unit, with statistically significant differences (p<0.01) among the groups. When the bleaching agent was not applied, the halogen light induced the highest temperature rise (2.38±0.66ºC). The LED unit produced the lowest temperature increase (0.29±0.13ºC); but there was no significant difference between LED unit and LED-laser system (0.35±0.15ºC) (p>0.01). When the bleaching agent was applied, there were significant differences among groups (p<0.01): halogen light induced the highest temperature rise (1.41±0.64ºC), and LED-laser system the lowest (0.33±0.12ºC); however, there was no difference between LED-laser system and LED unit (0.44±0.11ºC). LED and LED-laser system did not differ significantly from each other regardless the temperature rise occurred with or without bleaching agent application. It may be concluded that during light-activated tooth bleaching, with or without the bleaching agent, halogen light promoted higher pulp chamber temperature rise than LED unit and LED-laser system. The tested light-curing units provided increases in the pulp chamber temperature that were compatible with pulpal health.

A retrospective study of Traumatic Dental Injuries in a Brazilian dental urgency service

Epidemiologic aspects of traumatic dental injuries (TDI) were evaluated in the permanent dentition in a sample of 847 patients treated at the Dental Urgency Service of the Dental School of the Federal University of Goiás, Brazil, between May 2000 and May 2008. The statistical treatment analyzed data from frequency distribution and chi-square test. The level of significance was set at 5% for all analyses. The results showed a higher incident among males (610; 72.01%) with mean age of 6-10 year-old. Uncomplicated crown fracture (without pulp exposure) (502; 26.95%), avulsion (341; 18.30%) and complicated crown fracture (with pulp exposure) (330; 17.71%) were the most prevalent TDI. The prevalence of trauma throughout the years showed proportionality, being observed a larger number of cases between July and September (249; 29.39%). The most affected teeth were the maxillary central incisors (65.65%), followed by the maxillary left lateral incisors (19.67%). In 311 participants (18.25%), only one tooth was involved, while in most patients (536; 81.75%), TDI occurred in more than one tooth. Significant proportion (82.27%) of traumatized teeth presented completely formed root apex. The main etiologic factors involved in TDI were falls (51.71%), traffic accidents (22.90%) and violence (5.67%). Based on the obtained data, it may be concluded that accurate policies of TDI prevention must be established, capable of stimulating the exposure of appropriate protocols for management of these lesions. The prevalence of TDI in Goiânia subpopulation is compared to the prevalence reported in epidemiological studies in others populations.

Analysis of TMJ vibration sounds before and after use of two types of occlusal splints

Temporomandibular joint (TMJ) sounds are important and common physical signs of temporomandibular disorders (TMD). The aim of this study was to evaluate the influence of the effect of the use of occlusal bite splints (stabilizing and repositioning) on the sounds produced in the TMJ, by means of the electrovibratography (EVG). Thirty-one patients with TMD from the Dental School of Ribeirão Preto, University of São Paulo, Brazil were selected for this study. Group 1 (n=23) wore stabilizing bite splints and Group 2 (n=8) used anterior repositioning splints. Before and after treatment with occlusal splints both groups were analyzed using the SonoPAK Q/S recording system (BioResearch System, Inc.). The treatments with stabilizing bite splints were satisfactory, since they reduced the total amount of the sound energies (p<0.05), but the use of anterior repositioning splints for no more than 4 weeks produced significantly better results (p<0.01). The total amount of vibration energy involved in the vibrating movements of the TMJ showed significant improvement using anterior repositioning splints.

Níveis de concentrado e sais de cálcio de ácidos graxos para novilhos terminados em confinamento

Objetivou-se avaliar o efeito do nível de concentrado e dos sais de cálcio de ácidos graxos (SCAG) sobre o desempenho e qualidade da carne de novilhos terminados em confinamento. Sessenta novilhos Nelore e cruza Nelore foram divididos em quatro grupos e confinados por um período de 85 dias com as seguintes dietas: (BC) 46,7% de concentrado; (BC-SCAG) dieta BC acrescida de 3% de SCAG; (AC) dieta contendo 76,6% de concentrado e (AC-SCAG) dieta AC com 3% de SCAG. O nível de concentrado não influenciou o ganho médio diário, a espessura de gordura subcutânea e a área de olho de lombo, mas as dietas AC aumentaram o peso (P=0,0011) e o rendimento (P<0,0001) de carcaça, além da força de cisalhamento (P=0,0438). Animais alimentados com as dietas AC apresentaram maior peso (P=0,0011) e rendimento (P<0,0001) de carcaça em relação aos animais do tratamento BC. Os SCAG aumentaram o ganho de peso em dietas de AC (P=0,0311), mas sem efeito nas dietas BC. Animais tratados com as dietas contendo SCAG apresentaram maior peso (P=0,0133) e rendimento de carcaça (P=0,0160), mas sem diferenças na espessura de gordura subcutânea, área de olho de lombo e força de cisalhamento. Dietas de alto concentrado e os SCAG melhoraram as características quantitativas (peso e rendimento) das carcaças de bovinos na fase de terminação e podem ser utilizadas pelos produtores como alternativa para melhorar a eficiência do sistema de produção.

Avaliação da cicatrização de feridas em dorso de ratos tratados com mitomicina C tópica e posterior reforço com injetável

Estudo experimental em animais. A mitomicina C vem sendo usada como inibidor de fibroblastos, acarretando, com isso, diminuição do processo cicatricial em feridas cirúrgicas. OBJETIVO: Este trabalho visa avaliar o uso de Mitomicina C para diminuir o processo cicatricial, através de seu uso tópico com reforços posteriores injetáveis. MATERIAL E MÉTODOS: Foi usado um modelo de feridas em dorso de ratos, com retirada circular da pele e cicatrização por segunda intenção. Foram usados 18 ratos, divididos em três grupos: controle; com uso tópico; e com reforço de mitomicina C injetável, mensalmente e por 2 meses. Após 3 meses os animais foram sacrificados e as cicatrizes retiradas cirurgicamente e submetidas a estudo histológico. RESULTADOS: Notou-se sob vários critérios que a cicatrização com o uso tópico é menos intensa, mas ao se usar o reforço injetável os parâmetros voltam a ser comparados ao do grupo controle. DISCUSSÃO: Acreditamos que a administração injetável de mitomicina C nas cicatrizes, pela sua elevada característica tóxica, acarreta destruição tecidual e neoformação cicatricial. CONCLUSÕES: A mitomicina C diminui o processo cicatricial quando usada topicamente, mas acarreta aumento da cicatrização quando nestas feridas são feitos reforços injetáveis.

Distúrbios no perfil lipídico são altamente prevalentes em população nipo-brasileira

Alta prevalência de diabetes em população nipo-brasileira de Bauru/SP foi previamente relatada. Visando a complementar a avaliação do risco cardiometabólico, este estudo analisou distúrbios no perfil lipídico de 1.330 nipo-brasileiros (46% homens) > 30 anos. Definiu-se hipercolesterolemia por níveis de colesterol total > 240 mg/dL; hipertrigliceridemia por valores > 150 mg/dL e HDL-colesterol baixo por valores < 40 mg/dL e < 50 mg/dL para homens e mulheres, respectivamente. A prevalência desses distúrbios foi comparada pelo qui-quadrado, estratificando-se por sexos e categorias glicêmicas. As médias dos lipídeos e lipoproteínas foram comparadas entre sexos pelo teste t de Student. A prevalência de hipertrigliceridemia foi de 66,0% (IC95%:63,5 - 68,5%), sendo mais comum em homens e aumentando com a piora da categoria glicêmica; a trigliceridemia média foi 235,7 ± 196,3 mg/dL. A prevalência de hipercolesterolemia foi 24,4% (IC95%:22,1 - 26,7%); HDL-C baixo foi observado em 43,0% (IC95%:39,4 - 46,6%] das mulheres e 17,5% (IC95%:14,5 - 20,5%) dos homens, porém a razão colesterol total/HDL-C foi menor em mulheres (4,23 ± 0,68 vs. 4,40 ± 0,73; p < 0,001). Em nipo-brasileiros, a hipertrigliceridemia é a anormalidade lipídica mais comum, em concordância com a elevada prevalência de diabetes. Os homens apresentaram pior perfil lipídico que as mulheres. Sugere-se que hábitos de vida ocidental possam estar deteriorando a saúde desses indivíduos.

Prevalência de sobrepeso e obesidade em nipo-brasileiros: comparação entre sexos e geração

OBJETIVO: Descrever a prevalência de sobrepeso, obesidade e obesidade abdominal em nipo-brasileiros residentes na cidade de Bauru (SP), Brasil. MÉTODOS: Os dados foram obtidos a partir de um estudo transversal com 1 330 nipo-brasileiros de 1ª e 2ª geração, de ambos os sexos, com idade >30 anos. Os critérios para sobrepeso e obesidade foram índice de massa corporal entre 25-29,9kg/m² e >30kg/m², respectivamente. A obesidade abdominal foi classificada com valores de circunferência da cintura >90cm, para homens, e >80cm para mulheres. Foram calculadas as prevalências de sobrepeso, obesidade e obesidade abdominal por ponto e por intervalo, com 95% de confiança. RESULTADOS: Verificou-se que a prevalência de sobrepeso em nipo-brasileiros foi de 26,1% e 27,9% na primeira geração e de 44,8% e 32,5% na segunda geração, respectivamente, para homens e mulheres. Em relação à obesidade, a prevalência entre homens foi de 3,7% e 12%, e nas mulheres de 6,6% e 9,9% respectivamente na primeira e na segunda geração. Observou-se aumento na prevalência de sobrepeso e obesidade nos homens entre as gerações, apesar de as diferenças não serem estatisticamente significantes. A obesidade abdominal nos homens de primeira e segunda geração foi de 32,1% e 45,3%, e nas mulheres estes valores foram de 49,2% e 48,5%, respectivamente. No período de estudo não foram observados aumentos nas prevalências de sobrepeso e obesidade estatisticamente significantes (p<0,05). CONCLUSÃO: O aumento percentual na prevalência de sobrepeso e obesidade abdominal em nipo-brasileiros pode ser, em parte, explicado pelo processo da ocidentalização, reforçando a necessidade de medidas preventivas, visando a minimizar as conseqüências metabólicas da obesidade nos nipo-brasileiros.

EXISTENCE RESULTS FOR NEUTRAL INTEGRO-DIFFERENTIAL EQUATIONS WITH UNBOUNDED DELAY

In this paper we discuss the existence of mild, strict and classical solutions for a class of abstract integro-differential equations in Banach spaces. Some applications to ordinary and partial integro-differential equations are considered.

First stars XII. Abundances in extremely metal-poor turnoff stars, and comparison with the giants

Context. The detailed chemical abundances of extremely metal-poor (EMP) stars are key guides to understanding the early chemical evolution of the Galaxy. Most existing data, however, treat giant stars that may have experienced internal mixing later. Aims. We aim to compare the results for giants with new, accurate abundances for all observable elements in 18 EMP turno. stars. Methods. VLT/UVES spectra at R similar to 45 000 and S/N similar to 130 per pixel (lambda lambda 330-1000 nm) are analysed with OSMARCS model atmospheres and the TURBOSPECTRUM code to derive abundances for C, Mg, Si, Ca, Sc, Ti, Cr, Mn, Co, Ni, Zn, Sr, and Ba. Results. For Ca, Ni, Sr, and Ba, we find excellent consistency with our earlier sample of EMP giants, at all metallicities. However, our abundances of C, Sc, Ti, Cr, Mn and Co are similar to 0.2 dex larger than in giants of similar metallicity. Mg and Si abundances are similar to 0.2 dex lower (the giant [Mg/Fe] values are slightly revised), while Zn is again similar to 0.4 dex higher than in giants of similar [Fe/H] (6 stars only). Conclusions. For C, the dwarf/giant discrepancy could possibly have an astrophysical cause, but for the other elements it must arise from shortcomings in the analysis. Approximate computations of granulation (3D) effects yield smaller corrections for giants than for dwarfs, but suggest that this is an unlikely explanation, except perhaps for C, Cr, and Mn. NLTE computations for Na and Al provide consistent abundances between dwarfs and giants, unlike the LTE results, and would be highly desirable for the other discrepant elements as well. Meanwhile, we recommend using the giant abundances as reference data for Galactic chemical evolution models.

Genome-wide SNP genotyping highlights the role of natural selection in Plasmodium falciparum population divergence

Background: The malaria parasite Plasmodium falciparum exhibits abundant genetic diversity, and this diversity is key to its success as a pathogen. Previous efforts to study genetic diversity in P. falciparum have begun to elucidate the demographic history of the species, as well as patterns of population structure and patterns of linkage disequilibrium within its genome. Such studies will be greatly enhanced by new genomic tools and recent large-scale efforts to map genomic variation. To that end, we have developed a high throughput single nucleotide polymorphism (SNP) genotyping platform for P. falciparum. Results: Using an Affymetrix 3,000 SNP assay array, we found roughly half the assays (1,638) yielded high quality, 100% accurate genotyping calls for both major and minor SNP alleles. Genotype data from 76 global isolates confirm significant genetic differentiation among continental populations and varying levels of SNP diversity and linkage disequilibrium according to geographic location and local epidemiological factors. We further discovered that nonsynonymous and silent (synonymous or noncoding) SNPs differ with respect to within-population diversity, interpopulation differentiation, and the degree to which allele frequencies are correlated between populations. Conclusions: The distinct population profile of nonsynonymous variants indicates that natural selection has a significant influence on genomic diversity in P. falciparum, and that many of these changes may reflect functional variants deserving of follow-up study. Our analysis demonstrates the potential for new high-throughput genotyping technologies to enhance studies of population structure, natural selection, and ultimately enable genome-wide association studies in P. falciparum to find genes underlying key phenotypic traits.

Acute and chronic effects of exercise on inflammatory markers and B-type natriuretic peptide in patients with coronary artery disease

Few studies have prospectively addressed the effects of exercise in the inflammatory activity of patients with coronary artery disease (CAD). We sought to evaluate the consequences of an acute bout of exercise on inflammatory markers and BNP in untrained CAD patients before and after randomization to a training program. 34 CAD patients underwent a 50-min acute exercise session on a cycle-ergometer at 65% peak oxygen uptake before and after blood sampling. They were then randomized to a 4-month chronic exercise program (15 patients) or general lifestyle recommendations (19 patients), undergoing a new acute session of exercise after that. In the overall population, acute exercise caused a significant increase in C-reactive protein [CRP; 1.79 (4.49) vs. 1.94 (4.89) mg/L, P < 0.001], monokine induced by interferon-gamma [Mig; 351 (324) vs. 373 (330) pg/mL, P = 0.027] and vascular adhesion molecule-1 [VCAM-1; 226 (82) vs. 252 (110) pg/mL, P = 0.02]. After 4-months, in exercise-trained patients, there was a significant decrease in the inflammatory response provoked by the acute exercise compared to patients in the control group reflected by a significant decrease in the differences between rest and post-exercise levels of CRP [-0.29 (0.84) mg/L vs. -0.11 (0.21) mg/L, P = 0.05]. Resting BNP was also significantly lower in exercise-trained patients when compared to untrained controls [15.6 (16.2) vs. 9.7 (11.4) pg/mL, P = 0.04 and 19.2 (27.8) vs. 23.2 (27.5) pg/mL, P = 0.76; respectively]. Chronic exercise training might partially reverse the inflammatory response caused by acute exercise in CAD patients. These results suggest that regular exercise is an important nonpharmacological strategy to the improvement in inflammation in CAD patients.

Manipulation of rest period length induces different causes of fatigue in vertical jumping

The aim of this study was to directly compare the causes of fatigue after a short- and a long-rest interval between consecutive stretch-shortening cycle exercises. Eleven healthy males jumped with different resting period lengths (short = 6.1 +/- 1 s, long = 8.6 +/- 0.9 s), performing countermovement jumps at 95% of their maximal jump height until they were unable to sustain the target height. After short- and long-rest, the maximal voluntary isometric contraction knee extension torque decreased (-7%; p = 0.04), comparing to values obtained before exercise protocols. No change was seen from pre- to post-exercise, for either short- or long-rest, in biceps femoris coactivation (-1%; p = 0.95), peak-to-peak amplitude (1%; p = 0.95) and duration (-8%; p = 0.92) of the compound muscle action potential of the vastus lateralis. Evoked peak twitch torque reduced after both exercise protocols (short = -26%, long = -32%; p = 0.003) indicating peripheral fatigue. However, central fatigue occurred only after short-rest evidenced by a reduction in voluntary activation of the quadriceps muscle (-14%; p = 0.013) measured using the interpolated twitch technique. In conclusion, after Stretch-shortening cycle exercise using short rest period length, the cause of fatigue was central and peripheral, while after using long rest period length, the cause of fatigue was peripheral.

Profiles of xylose reductase, xylitol dehydrogenase and xylitol production under different oxygen transfer volumetric coefficient values

BACKGROUND: Xylitol is a sugar alcohol (polyalcohol) with many interesting properties for pharmaceutical and food products. It is currently produced by a chemical process, which has some disadvantages such as high energy requirement. Therefore microbiological production of xylitol has been studied as an alternative, but its viability is dependent on optimisation of the fermentation variables. Among these, aeration is fundamental, because xylitol is produced only under adequate oxygen availability. In most experiments with xylitol-producing yeasts, low oxygen transfer volumetric coefficient (K(L)a) values are used to maintain microaerobic conditions. However, in the present study the use of relatively high K(L)a values resulted in high xylitol production. The effect of aeration was also evaluated via the profiles of xylose reductase (XR) and xylitol clehydrogenase (XD) activities during the experiments. RESULTS: The highest XR specific activity (1.45 +/- 0.21 U mg(protein)(-1)) was achieved during the experiment with the lowest K(L)a value (12 h(-1)), while the highest XD specific activity (0.19 +/- 0.03 U mg(protein)(-1)) was observed with a K(L)a value of 25 h(-1). Xylitol production was enhanced when K(L)a was increased from 12 to 50 h(-1), which resulted in the best condition observed, corresponding to a xylitol volumetric productivity of 1.50 +/- 0.08 g(xylitol) L(-1) h(-1) and an efficiency of 71 +/- 6.0%. CONCLUSION: The results showed that the enzyme activities during xylitol bioproduction depend greatly on the initial KLa value (oxygen availability). This finding supplies important information for further studies in molecular biology and genetic engineering aimed at improving xylitol bioproduction. (C) 2008 Society of Chemical Industry

A novel electrocatalyst support with proton conductive properties for polymer electrolyte membrane fuel cell applications

The objective of this study is to graft the Surface of carbon black, by chemically introducing polymeric chains (Nafion (R) like) with proton-conducting properties. This procedure aims for a better interaction of the proton-conducting phase with the metallic catalyst particles, as well as hinders posterior support particle agglomeration. Also loss of active surface call be prevented. The proton conduction between the active electrocatalyst site and the Nafion (R) ionomer membrane should be enhanced, thus diminishing the ohmic drop ill the polymer electrolyte membrane fuel cell (PEMFC). PtRu nanoparticles were supported on different carbon materials by the impregnation method and direct reduction with ethylene glycol and characterized using amongst others FTIR, XRD and TEM. The screen printing technique was used to produce membrane electrode assemblies (MEA) for single cell tests in H(2)/air(PEMFC) and methanol operation (DMFC). In the PEMFC experiments, PtRu supported on grafted carbon shows 550 mW cm(-2) gmetal(-1) power density, which represents at least 78% improvement in performance, compared to the power density of commercial PtRu/C ETEK. The DMFC results of the grafted electrocatalyst achieve around 100% improvement. The polarization Curves results clearly show that the main Cause of the observed effect is the reduction in ohmic drop, caused by the grafted polymer. (C) 2009 Elsevier B.V. All rights reserved.

Modeling and analysis of laminate composite plates with embedded active-passive piezoelectric networks

The objective of this work is to present the finite element modeling of laminate composite plates with embedded piezoelectric patches or layers that are then connected to active-passive resonant shunt circuits, composed of resistance, inductance and voltage source. Applications to passive vibration control and active control authority enhancement are also presented and discussed. The finite element model is based on an equivalent single layer theory combined with a third-order shear deformation theory. A stress-voltage electromechanical model is considered for the piezoelectric materials fully coupled to the electrical circuits. To this end, the electrical circuit equations are also included in the variational formulation. Hence, conservation of charge and full electromechanical coupling are guaranteed. The formulation results in a coupled finite element model with mechanical (displacements) and electrical (charges at electrodes) degrees of freedom. For a Graphite-Epoxy (Carbon-Fibre Reinforced) laminate composite plate, a parametric analysis is performed to evaluate optimal locations along the plate plane (xy) and thickness (z) that maximize the effective modal electromechanical coupling coefficient. Then, the passive vibration control performance is evaluated for a network of optimally located shunted piezoelectric patches embedded in the plate, through the design of resistance and inductance values of each circuit, to reduce the vibration amplitude of the first four vibration modes. A vibration amplitude reduction of at least 10 dB for all vibration modes was observed. Then, an analysis of the control authority enhancement due to the resonant shunt circuit, when the piezoelectric patches are used as actuators, is performed. It is shown that the control authority can indeed be improved near a selected resonance even with multiple pairs of piezoelectric patches and active-passive circuits acting simultaneously. (C) 2010 Elsevier Ltd. All rights reserved.